Reversing the doors of a Liebherr refrigerator: instructions with photos and expert advice

Rehanging refrigerator doors Liebherr is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Unlike budget models, premium-segment appliances (for example, series Premium NoFrost or BioFresh) require care: here it is important not only to remove the hinges correctly, but also to maintain the tightness of the seal, avoid skewing the door and not damage the system SmartDevice (if there is one).

This article contains a step-by-step guide taking into account the features of different lines Liebherr, including models with two-chamber system and built-in refrigerators. We'll look at what tools you'll need, how to avoid common mistakes (for example, damage to hinges due to uneven load distribution), and give tips on adjusting the door after installation. And if your model is equipped with a display or touch buttons, we will separately dwell on the nuances of working with electronics.

Spoiler: the process will take from 1 to 3 hours depending on experience, but with our instructions you will save on calling a specialist (the average cost of the service is from 3,500 to 7,000 rubles). The main thing is to take your time and follow the algorithm, especially if you have a model with automatic door opening (for example, Liebherr ICBN 3366).

Preparation: tools and conditions

Before hanging the door, make sure that you have everything you need. Liebherr supplies with most models a special key for adjusting the hinges (usually a 5 or 6 mm hexagon), but if it is not there, a standard set will do. Here is the complete list:

• 🔧 Hex keys (5 mm, 6 mm) - for fastening the hinges.
• 🔨 Phillips screwdriver (PH2) and flat - for dismantling decorative panels.
• 📏 Level (preferably laser) - to avoid door skewing.
• 🧲 Magnet or telescopic gripper - for removing fallen bolts.
• 🧴 Silicone grease (for example, WD-40 Specialist) - for processing hinges after installation.
• 🧊 Hair dryer (optional) - if the seal is “stuck” to the body.

Important: if you have a model with display on the door (for example, Liebherr SBSes 7256), additionally prepare:

• 🔌 A screwdriver with an insulated handle - for working with the display power contacts.
• 📱 Smartphone - to photograph the wiring diagram (if you have to disconnect them).

Work in a well-lit room, having first disconnected the refrigerator from the mains. If the model is with NoFrost system, wait for complete defrosting (at least 12 hours) - this will make it easier to dismantle the seal. For models Liebherr with function SuperCool After disconnecting from the network, residual voltage may remain in the capacitors - wait 10-15 minutes before working.

Step 1: Dismantling the old door

Start with the top hinge - it usually fixes the main load. In most models Liebherr (for example, CNes 4315) the hinges are closed with decorative caps. To remove them:

1. Pry the cap from the side (not). from above, so as not to damage the plastic).
2. Unscrew the bolts with a hexagon counterclockwise. In some models, the bolts may have a Phillips screwdriver - check in advance.
3. Hold the door when you remove the last bolt - it is heavier than it seems (the weight of the door with shelves can reach 15-20 kg).

After removing the upper hinge, carefully lift the door up to free it from the lower hinge. If the door is “jammed”, do not pull by force - check if the seal or magnetic lock is in the way (for models with system SmartDevice).

⚠️ Attention: For models Liebherr with automatic ice dispenser (for example, SBSes 8665) there are water supply hoses at the bottom of the door. Do not pull the door up until you disconnect them! two sides at the same time.

Step 2: Transferring the hinges to the other side

The hinges on the refrigerator body are attached symmetrically, but the holes for them can be closed with plugs. Remove the plugs. with a flat screwdriver - they are usually held on by latches. If there are no holes (as in some models), you will have to drill new ones. To do this: BioFresh), you will have to drill new ones. To do this:

• 📏 Measure the distance from the edge of the case to the center of the holes on the old side.
• 🔍 Transfer the markings to the other side. side using a level.
• 🔨 Drill holes with a metal drill (diameter is 0.5 mm less than the diameter of the bolts).

When transferring hinges, keep in mind that models with two-chamber system (for example, Liebherr CBNes 5155) have upper and the lower hinges may differ in design. Do not confuse them! The hinges usually have markings: TOP (upper) and BOTTOM (lower).

⚠️ Attention: For built-in models (for example, Liebherr CUag), the hinges can be attached to the furniture facade, and not to the refrigerator body. In this case, you will have to rehang the entire facade, which is more difficult - you may need the help of a carpenter.

Step 3: Installing the door on the new side

Before installing the door, check that:

• 🔄 The hinges are fixed in a mirror image with respect to the original position.
• 🧲 The seal is clean and not deformed (if necessary, wash it with warm water and soap).
• 🔌 The display wires (if any) are not twisted or strained.

Installation occurs in the reverse order:

1. Place the door onto the lower hinge, holding it at an angle of 45°.
2. Lower the door down, aligning the top hinge with the holes.
3. Tighten the bolts, starting from the top hinge (but not all the way!).
4. Adjust the door position to the level, then finally tighten the fasteners.

For models with touch control (for example, Liebherr SBS 86I2) after installing the door, you may need to reset the display settings. To do this:

Press and hold the "SuperCool" + "SuperFrost" buttons for 10 seconds.

Adjusting and checking the tightness

After installing the door, it needs to be adjusted to avoid distortion and ensure a tight fit. fit of the seal. For this, adjusting bolts are provided on the hinges: Liebherr For this purpose, adjusting bolts are provided on the hinges:

• 🔧 Vertical position: adjustable by the upper bolt on the top hinge (turning clockwise raises the door, counter-clockwise lowers it).
• 🔄 Horizontal position: adjustable side bolts on both hinges.
• 📉 Sealant fit: checked with a sheet of paper - it should be pressed tightly around the entire perimeter.

If the seal allows air to pass through, try:

• 🧼 Wipe it with a solution of vinegar (1:1 with water) - this will restore elasticity.
• 🔥 Heat the problem areas with a hair dryer (no higher than 60°C) and shape it with your hands.
• 🛠️ As a last resort, replace the seal (original for Liebherr can be ordered by model code).

For models with system BioFresh (for example, Liebherr CBNes 5767after adjusting the door, check the temperature in the freshness zone - it must correspond to the factory settings (+1°C for DrySafe i 0°C for HydroSafe). If the temperature has changed, perform calibration through the menu:

Settings → Temperature → Calibration → BioFresh

Common mistakes and how to avoid them

Even with careful work, you can make mistakes that will lead to problems. Here are the most common ones:

• 🚫 Tightening the bolts: this deforms the hinges and leads to the door being skewed. Tighten the bolts with a force of no more than 2–3 Nm (use a torque wrench, if available).
• 🔌 Damage to the display wiring: for models with SmartDevice the wires may fray if handled carelessly. Always secure them with zip ties.
• 🧲 Ignoring the magnetic seal: if it is not cleaned of dirt, the door will not be airtight and the compressor will overload.
• 🔧 Use of unsuitable bolts: c complete with Liebherr come bolts with a special coating - do not replace them with regular ones to avoid corrosion.

Pay special attention to models with automatic door opening (for example, Liebherr ICBN 3366). After rehanging, you may need to reconfigure the opening mechanism through the service menu:

Press "Light" + "SuperCool" + "SuperFrost" at the same time, then select the "Door Adjustment" item.

⚠️ Attention: If, after rehanging the door, the refrigerator becomes louder, check that the seal does not touch the inner walls. Vibration can be transmitted to the chassis, increasing the noise. The solution is to bend the seal or adjust the hinges.

Features for different Liebherr series

The design of hinges and doors may vary depending on the series. Here are the key nuances:

For models with two-chamber system (for example, Liebherr SBSes 7256), re-hanging the upper and lower doors is done separately. Start with the upper chamber (freezer), since its door is usually carried out separately. easier.

What to do if the door does not close after rehanging?

Check if anything is in the way inside the refrigerator (shelves, containers). Also, the cause may be a deformed seal or incorrectly adjusted hinges. Try loosening the bolts and adjusting the door. again.

FAQ: Answers to frequently asked questions

Is it possible to hang the door of a Liebherr refrigerator yourself if you have no experience?

Yes, but start with simple models without electronics (for example, Liebherr CN 4315If you have a model with a display or). system SmartDevice, it is better to invite an assistant or a technician - errors when working with the wiring can damage the electronic unit.

How much does it cost to rehang a door at a Liebherr service center?

The cost depends on the model and region: On average:

• Simple models. (for example, Liebherr CNes 4315) - 3,500–4,500 rubles.
• Models with a display (for example, Liebherr SBSes 7256) - 5,000–7,000 rubles.
• Built-in models - from 7 000 rubles (work with a furniture facade is required).

Prices are valid for Moscow and St. Petersburg. In the regions they may differ by 15–20%.

Do you need to defrost the refrigerator before hanging the door?

Required if you have a model with system. NoFrost Drip system door level.. Even if there is no ice, defrosting will relieve stress from the seal and facilitate dismantling. For models with drip system (for example, Liebherr CUag 3311), defrosting is not necessary, but is recommended for convenience.

What should I do if the Liebherr refrigerator door does not close after rehanging?

The reasons may be different:

• 🔧 The hinges are not adjusted correctly - loosen the bolts and level the door.
• 🧲 The seal is dirty or deformed - clean it or heat it with a hair dryer.
• 🏠 The refrigerator is not level - adjust the legs.
• 🔌 Problems with the magnetic lock (for models with SmartDevice) - reset the settings.

If the problem is not solved, check whether the door body was bent during dismantling.

Is it possible to rehang the door on a Liebherr refrigerator with a display?

Yes, but it is more difficult. You will need:

1. Disconnect the display wires (memorize or take a photo of the connection diagram!).
2. Move the hinges and shock absorbers (if any).
3. Connect the wires back, making sure they are not strained.
4. Reset the display settings (usually holding the buttons SuperCool + SuperFrost).

If you are not sure, contact the service center. Errors when working with electronics can lead to failure of the control module.