Rearranging furniture or changing the layout of the kitchen often dictates its conditions for the location of household appliances. Refrigerator owners Leran often face the need to change the opening direction of the door to ensure convenient access to products and ergonomic use of space. This process does not require calling a specialist, but it does imply the presence of basic tools and strict adherence to the sequence of actions. Rehanging doors is an operation that is quite possible to perform independently if you carefully study the design of the hinges and prepare the workplace.
It is worth considering that refrigerator models Leran, like any other equipment have their own design features for fastening. An incorrect dismantling sequence can lead to damage facade panel or deformation of the sealing rubber. Before starting work, it is strongly recommended to empty the refrigerator of food and completely defrost it if the model has a drip system or manual moisture removal.
In this article we will analyze in detail the algorithm of actions for various modifications, pay attention to the nuances of rearranging the handles and adjusting the magnetic latches. It is important to understand that manufacturer’s warranty can be saved only in the absence of mechanical damage received during independent intervention. Therefore, every movement must be balanced, and the tool used must be in good working order.
Necessary tools and preparation of the workplace
High-quality preparation is the key to successful completion of the work without scratches on the floor or chips on the body of the equipment. To rehang refrigerator doors Leran you will need a standard DIY kit, which can be found in the garage or toolbox of most men. The main requirement is the presence of a set hex keys and Phillips screwdrivers, since this is the fastener most often used by the manufacturer.
Be sure to prepare a soft substrate, for example, a thick blanket or a piece of cardboard, on which you will lay the removed doors. This will prevent dents from appearing on the metal surface and protect the inner shelf from accidental impact. It would also be a good idea to have masking tape on hand, which can be used to secure the moving elements while unscrewing the bolts.
- 🛠️ A set of screwdrivers (phillips and flat) of different sizes for working with screws of different diameters.
- 🔧 A set of hex keys (imbus), often a size of 4 mm or 5 is required mm.
- 🧤 Work gloves to protect your hands from sharp metal edges and contamination.
- 📏 A level or tape measure to control the horizontalness of the installation after completion of work.
Pay special attention to organizing the space around the refrigerator. You will need free access to the equipment from all sides, so it is best to move the unit away from the wall at a distance of at least a meter. This will ensure good ventilation and allow you to move freely without the risk of tripping over wires or furniture legs.
Removing the top panel and top door
The process begins with removing the top cover of the refrigerator, if it is structurally provided for in your model Leran. In some modifications, the top panel is decorative and is secured with latches; in others, it is necessary to unscrew the screws from the back. Carefully move the panel back or up to gain access to the upper fasteners door hinges.
Next we move on to the very top door. If you have a two-chamber refrigerator, then dismantling begins with it. First you need to remove the handle if it is not integrated into the profile, or simply gain access to the top hinge mounting bolts. In models with a display on the door, you must first disconnect the cable cablegoing to the control panel.
⚠️ Attention: Before disconnecting any electrical connectors, be sure to turn off the power to the refrigerator by unplugging the plug from the socket. Working with live electrical wiring is strictly prohibited and can lead to failure of the electronics.
After you have unscrewed the bolts holding the top hinge, you must hold the door with your other hand so that it does not fall. The weight of the door can be significant, especially if glass shelves are installed inside. Smoothly remove the door from the lower pin of the hinge (if it is composite) or completely dismantle it along with the hinge, depending on the design.
Requires special attention sealing rubber band. When removing the door, try not to catch it with the sharp corners of the tools, since damage to the integrity of the seal will lead to loss of tightness and poor cooling. If a shelf for bottles or eggs is installed on the door, it is better to remove it in advance to reduce the weight and dimensions of the structure.
☑️ Preparation for dismantling
Removing the middle hinge and main chamber
After the top door is removed and put aside in a safe place, access to the middle hinge, which holds the main chamber of the refrigerator, opens. Depending on the model Leran, this hinge can be combined with the upper door mount or be a separate unit. Unscrew the mounting bolts that hold the mechanism in the housing.
The main door of the refrigerator is usually heavier than the freezer, so the help of a second person is especially important here. One person holds the door, the second unscrews the bolts and removes the hinge. Do not try to hold a massive structure with one hand, this can lead to a back injury or falling of the equipment.
At this stage, they often open mounting holes on the opposite side of the case, which are closed with decorative plugs. They must be carefully removed. Usually the plugs fit tightly, and to remove them you can use a thin knife blade or a flat screwdriver wrapped in a cloth so as not to scratch the metal.
- ❄️ Save the removed plugs; they will be needed for installation on the free side after rehanging.
- 🔩 Place all screws and bolts in a separate container so that they do not get lost during work.
- 🧹 Wipe the freed holes from dust and possible factory grease before installing new elements.
It is important to note that in some models Leran the design of the middle hinges assumes the presence pin, which is inserted into the door body. When dismantling, you need to ensure that this pin does not fall or get lost, since it is a critical element for centering the door.
Flipping the doors and rearranging the fittings
The most critical stage is the physical rearrangement of the door leaves to the other side. To do this, you need to turn the removed doors over. Please note that along with the door you need to rearrange and handlesif they are not symmetrical. In most cases, the handles are attached to screws on the inside of the door, which makes it easy to move them to the opposite end.
When moving handles, make sure that you use the holes designed specifically for your model. Manufacturers often drill universal holes for different configurations, closing the extra ones with plastic plugs. If the holes do not match, you may need to use fasteners from a special set, which sometimes comes with the refrigerator.
Nuances with magnetic latches
In some models of Leran refrigerators, the magnetic latch (mating part) is built into the body and does not require rearrangement, since the magnets in the door work on both sides. However, if you have a mechanical latch, you must move it to the new side, otherwise the door will not close tightly.
Don't forget about stops and opening limiters. If your model has a plastic stop that prevents the door from swinging open more than 90 degrees, it will also need to be repositioned. Ignoring this step may result in the door opening too wide and damaging nearby furniture or resting against the wall.
After rearranging all the hardware on the door, you can begin installing the hinges on the new side. It is important here not to confuse the upper and lower loops if they have different designs. They are usually marked or have differences in shape that cannot be ignored upon close inspection.
Assembling the structure and adjusting the gaps
Assembly is carried out in the reverse order of dismantling. First, the main door of the refrigerator compartment is installed. Align the holes in the door with the holes in the body, insert the bottom pin (if there is one) and secure the hinge with bolts. Do not tighten the bolts “all the way” right away, leave a small gap for later adjustment.
Then the upper door (freezer) is installed. Align it with the bottom so that the gap between the doors is uniform along the entire length. After this, you can finally tighten all fasteners. The uniformity of the gap is a key indicator of correct installation.
| Adjustment element | Tool | Purpose of adjustment | Sign of correct installation |
|---|---|---|---|
| Legs refrigerator | Adjustable wrench | Horizon leveling | The refrigerator does not wobble, the level bubble is in the center |
| Upper hinge | Hexagon | Gap between doors | Uniform gap across the entire width (2-3 mm) |
| Bottom hinge | Open-end wrench | Tightness | The door closes itself with a slight push |
Pay special attention adjusting the height of the legs. If the refrigerator is tilted, the doors may open spontaneously or, conversely, not close completely. The ideal position is when the refrigerator is slightly tilted back (about 2 degrees), which ensures natural closing under the influence of gravity.
After tightening all the bolts, check the operation of the doors. They should open and close smoothly, without squeaks or jams. The seal must be in contact with the housing along its entire perimeter. If you notice a loose fit in one of the corners, you may need to fine-tune the position of the hinge.
Typical errors and troubleshooting
Even if you carefully follow the instructions, you may encounter difficulties. One of the most common mistakes is mixing up the sides of the hinges. Study the design carefully: often the left and right sides have different geometry of holes or stops. If the hinge does not snap into place without effort, then you are trying to install it incorrectly.
Another common problem is the door being skewed after assembly. This occurs if the bolts have been tightened without first being aligned. In this case, you will have to loosen the fasteners, align the door and tighten the bolts again. Also, the cause of the misalignment may be an adjusting screw in the lower hinge that is not fully screwed in.
⚠️ Attention: If after rehanging the door does not close tightly and there is blowing from the refrigerator, check the condition of the rubber seal. When dismantling it is easy to damage or move. Insert the elastic into the groove all the way around.
If you encounter a situation where the holes on the new side do not line up with the holes on the door, do not try to drill new holes in the metal. This may damage the thermal insulation and lead to corrosion. Most likely, your model Leran provides an alternative method of fastening or requires the use of adapter bushings.
Frequently asked questions (FAQ)
Do I need to call a technician to rehang the doors on a Leran refrigerator?
No, it is not necessary to call a technician. Manufacturers design refrigerators with the ability to be re-weighed independently. However, if you are not confident in your abilities or you do not have the necessary tools, it is better to turn to professionals to avoid damage to expensive equipment.
Will the warranty remain valid after re-hanging the doors yourself?
The warranty remains valid if during the work you did not cause mechanical damage to the housing, hinges or seal, and also did not break the seals on the compressor (which re-hanging the doors is difficult). The main thing is to act carefully and according to the instructions.
What to do if, after rehanging, the door does not fit well?
Check the adjustment of the legs of the refrigerator - it should be slightly tilted back. Also inspect the rubber seal for any creases. If the problem persists, try loosening the hinges, pressing the door tightly against the body and tightening the bolts again.
Is it possible to rehang the door if the refrigerator has a display?
Yes, it is possible, but it requires more caution. It is necessary to carefully disconnect the cable cable, move it to the other side (if the length allows) or reconnect it to the appropriate connector if the design provides for versatility. In some models, you don’t need to change the length of the wire, you just need to throw a loop.