Changing the kitchen layout or simply wanting to optimize space often requires moving refrigeration equipment. Models Nord Frost are designed taking into account the possibility of re-hanging the doors, which makes the process accessible even to an inexperienced user. However, despite its apparent simplicity, the procedure requires strict adherence to the sequence of actions and an understanding of the design of the loop mechanism loop mechanism.
Incorrect installation can lead to leakage, skew of the blade and, as a result, failure of the compressor due to constant operation. In this article, we will look in detail at how to hang the door on a refrigerator Nord Frost, what tools will be required and what nuances owners of models with the system should pay special attention to No Frost.
Before starting work, it is strongly recommended to clear the working space around the unit. You will need access to the equipment from all sides, since manipulations will be carried out from above, below, and from the sides of the case. Make sure the floor is level and there is nothing lying under your feet.
Necessary tools and workplace preparation
Quality preparation is half the success. To work with refrigerator fasteners Nord Frost you will need a basic DIY kit. In most cases, a standard a Phillips screwdriver wrench is sufficient, but the design of some models may require hexagons.
It is important to prepare a soft substrate, such as cardboard or thick fabric, in order to place the removed door on the floor and not damage the decorative coating or sealing rubber. It would also be a good idea to have a plastic spatula or a flat spatula wrapped in a rag on hand to carefully remove decorative plugs.
- 🔧 Phillips and flathead screwdrivers (preferably with magnetic tips).
- 🔩 A wrench or a set of sockets (most often the size is 8 or 10 mm).
- 🛠️ Hex key (depending on the model Nord Frost).
- 🧤 Gloves to protect your hands from sharp edges and grease.
⚠️ Attention: Before starting any work, be sure to disconnect the refrigerator from the electrical network! This is a basic rule electrical safety, ignoring which is unacceptable.
Remove all products and removable shelves from the refrigerator and freezer compartments. This will significantly reduce the weight of the structure and protect the glass elements from falling during dismantling. boxes, it is also better to remove them in advance.
Algorithm for dismantling the upper door of the refrigerator compartment
The process of removing the door leaf begins from the top of the case. On refrigerators Nord Frost the upper hinge is often hidden under a decorative plug, which must be carefully pryed off with a flat object. so as not to break the plastic clips.
After removing the plug, access to the mounting bolts will open. Before completely unscrewing the top hinge, you must fix the door in the open position or ask an assistant to hold it. The weight of the door leaf can be significant, and the risk of dropping it on your feet or damaging the floor is high.
Unscrew the bolts securing the top hinge counterclockwise. Do not rush to remove the hinge itself right away - on some models there may be a wire connected to it door open indicator or backlight control. If there are wires, carefully disconnect the connector, remembering its position.
Wiring nuances in Nord Frost models
In some In modifications of refrigerators, the wiring runs inside the door hinge. When removing the top hinge, the wires may become strained. Do not pull the hinge up sharply and disconnect the connectors. If the polarity is reversed during assembly, the indicator may not work correctly.
Now you can carefully lift the door up, removing it from the bottom hinge, and set it aside on the prepared surface. condition of the lower bushing or the pin on which the door rotated - it will also need to be rearranged.
Removing the lower door of the freezer
The lower door in refrigerators Nord Frost usually attached to one or two hinges located at the bottom. The principle of operation is similar to the upper one, but there are some peculiarities. Often the lower hinge is closed by a plinth or decorative strip.
Remove the protective panel at the bottom of the case. To do this, you may need to unscrew a few screws or simply pull the panel towards you, if it is held on by latches. After gaining access to the mechanism, unscrew the fastening bolts of the lower one. hinges.
As in the case of the upper door, hold the door when removing the fasteners. Remove the door from the support pin. If your model has an intermediate partition between the chambers, it may also need to be dismantled or rearranged, if the design Nord Frost implies this.
- ❄️ Remove all drawers and shelves to lighten the weight.
- 🔩 Unscrew the bottom hinge bolts using the appropriate wrench.
- 🚪 Carefully remove the freezer door from the support.
- 🧹 Clean the door ends from dust before installation.
⚠️ Attention: When removing the lower door, be careful not to damage capillary tube or other elements of the cooling system if they pass near the hinges. Mechanical damage to the circuit will lead to freon leakage.
After. After dismantling both doors, you will have a complete set of elements ready for rearrangement. Carefully inspect the removed parts for chips or corrosion. If defects are found, it is better to eliminate them before assembly.
Rearranging the hinges and fittings to the opposite side
The most important step is transferring the fasteners to the body. refrigerator Nord Frost there should already be technological holes on the opposite side, closed with plastic plugs. Remove these plugs and install them in the places where the hinges were previously attached.
Move the upper and lower hinges to new places. It is important to use exactly those holes that are intended for your side of installation. Often there are markings or diagrams on the case indicating which holes are active for the left one. or right-hand linkage.
☑️ Check before installation
Pay special attention to rearranging the support pins (bushings) on which the door is placed. They must be tightly fixed in the new sockets. If the pin has a thread, screw it in until it stops, but without excessive force, so as not to break the thread. in the body.
If your model is equipped with handles integrated into the door body, they may also need to be rearranged. To do this, remove the handles on one side and install the plugs, and on the opposite side, remove the plugs and mount the handles using standard fasteners.
Installing doors on the new side: step-by-step assembly
Assembly is carried out in the reverse order of dismantling. Start by installing the bottom door of the freezer. Place the panel on the bottom support pin and align it. Holding the door, install the bottom hinge in place and tighten the bolts by hand.
Do not immediately tighten the bolts “all the way”. and without distortions. After preliminary fixing the lower part, you can proceed to installing the upper door.
Install the upper door leaf, aligning the holes with the upper hinge. If the model has a system No Frost, carefully pull the wires through the holes in the hinge and connect the connectors. Make sure that the wires are not pinched or pinched. tense.
| Stage | Action | Key point |
|---|---|---|
| 1 | Installing the bottom door | Hit the support pin |
| 2 | Fixing the lower hinge | Do not tighten completely |
| 3 | Installing the upper door | Connecting the wiring (if any) |
| 4 | Final adjustment | Tightening all bolts |
After installing both blades, check for ease of movement. The doors should open freely, but when released, close on their own (if the opening angle is small) or remain in the specified position. Make sure that magnetic seal adjacent to the body along the entire perimeter.
Adjusting the position of the doors and checking the tightness
The final stage is adjustment. If the door is skewed and does not fit tightly, loosen the hinge mounting bolts (but do not unscrew them completely) and slightly move the door leaf in the desired direction. Once you have achieved a perfect fit, tighten the bolts tightly.
Checking the tightness is a critical point. Take a sheet of A4 paper, clamp it with the refrigerator door and try to pull it out. The paper should come out with noticeable force. If the sheet falls out freely or is pulled out too easily, it means that seal it does not fit tightly.
In some cases, it may be necessary to adjust the height of the refrigerator legs. If the unit is not level, the doors may open on their own or, conversely, not close completely. Use the leveling feet at the bottom of the housing for alignment.
⚠️ Attention: The design and location of the mounting holes may vary depending on the specific series Nord Frost. Always check the technical documentation of your model if the standard scheme is not suitable.
After completing all work, turn on the refrigerator. Let it run for 15-20 minutes, then check the temperature inside the chambers. If the cold accumulates normally and the doors close tightly, the procedure can be considered successfully completed.
Frequently asked questions (FAQ)
Is it necessary to defrost the refrigerator before re-hanging the doors?
Full defrosting is not necessary if you work quickly. However, if there is a lot of ice in the freezer, the weight of the ice may make removing the door difficult. It is recommended to remove all products, which will naturally lead to partial defrosting during operation.
What to do if the hinge holes on the new side are closed?
In 99% of cases, refrigerators Nord Frost have a symmetrical design. The holes are already drilled and covered with plastic plugs. If you do not find any holes, carefully inspect the end of the case - the plugs may be painted in the color of the case and are invisible at first glance. You cannot drill new holes!
Is it possible to hang the door alone?
Technically this is possible, especially for narrow models. However, refrigerator doors are heavy and bulky. The risk of dropping the unit, damaging the floor or causing injury is high. It is better to involve a second person to secure and support the canvas.
Why does the door not close completely after rehanging?
Most likely, the installation geometry is broken. Check if the refrigerator is level (use a level). Make sure that when you move the hinges you don't lose any washers or spacers that might be under the old hinge. Also check if anything inside (shelf, packaging) is in the way.
Does re-hanging the doors affect the warranty?
According to the law and rules of most service centers, re-hanging the doors yourself is not grounds for voiding the warranty if the unit components (hinges, housing, wiring) were not damaged in the process. However, keep all the removed parts in case you call for service.