Re-hanging the doors on a Siemens refrigerator: steps, tools and common mistakes

Hanging refrigerator doors Siemens is a task that owners face when moving, renovating a kitchen, or simply wanting to optimize space. The procedure seems simple, but requires care: improper installation can lead to distortion of hinges, tightness violation or even damage to the case. In this article we will analyze the process from A to Z - from preparing tools to final adjustment, taking into account the features of popular models Siemens (for example, series KG39, KG36 or KA92).

The main rule: not all refrigerators support double-sided hinges.. If your model has hinges installed on only one side from the factory, it will not be possible to rehang the door without replacing parts. Check this before starting work - the information is usually indicated in operating instructions or on the sticker inside the chamber.

In the article you will find:

• 🔧 Step-by-step instructions with photo analogues of the stages
• 📋 List of necessary tools and consumables
• ⚠️ Typical mistakes and how to avoid them
• 🔄 Features for models with freezer at the bottom/top
• 📊 Hinge compatibility table for different series Siemens

1. Preparation: tools and conditions

Before to begin dismantling, make sure that you have everything you need. Minimum set of tools:

• 🔨 Phillips and flathead screwdrivers (size depends on the hinge screws)
• 🔧 10 mm wrench or socket (for some models)
• 📏 Tape measure or ruler (to check gaps)
• 🧲 Magnet or tape (to temporarily fix the door)
• 🧴 Silicone grease (for hinges after installation)

Also prepare a working space:

• 🚪 Clear access to the refrigerator from all sides - at least 1 m of free space.
• 🧊 Unplug the appliance from the outlet and defrost (if you plan to work with the freezer).
• 📦 Remove all food and shelves from the door - they may fall when removal.
• 🧹 Place a soft cloth or cardboard under the door to avoid scratching the floor.

⚠️ Attention: If your refrigerator Siemens with a system NoFrost, after rehanging the doors it may be necessary restarting the fan. by holding the button SuperCool for 5 seconds (check the manual for the model).

On some models (for example, Siemens KG39NVI30) the hinges of the upper and lower doors differ in design. If you are reversing both doors (refrigerator and freezer), the hinges should not be mixed up - this will lead to uneven fit and cold leakage.

2. Dismantling the old door: a step-by-step process

Start with the top hinge - it usually fixes the main load. Algorithm of actions:

1. Open the refrigerator door 90°. Support it from below with a wooden block or ask an assistant to hold it.

2. Remove the decorative plug from the top hinge (pry it off with a flat-head screwdriver. The mounting screws are hidden under it.

3. Unscrew the screws with a Phillips screwdriver. In some models (for example, KG36NXA30) are used internal hexagon - prepare the appropriate key.

4. Carefully remove the door from the top hinge and lay it down onto the prepared surface. Do not pull it towards you - the hinge may catch on the body.

For the lower hinge:

• 🔩 Unscrew the screws securing the hinge to the body.
• 🚪 Remove the door completely, holding it by the bottom edge.
• 🔄 If the freezer is separate, repeat the process for its door.

Disconnected from the network

All products and shelves have been removed

A place has been prepared for the door

There is an assistant (for heavy models). data-i="116">Attention:

The places where the hinges are attached are photographed -->

⚠️ Attention: On models with electronic display (For example, Siemens iQ700) Removing the door may cut off power to the control panel. After re-hanging, you will have to reset the temperature settings - write down the current values ​​in advance.

3. Transferring loops to the other side

Now you need to move the loops to the opposite side:

For the top. hinges:

• 🔧 Move the mounting plates (if they are removable) to the other side using the existing holes.
• 📏 Check the symmetry: the distance from the edge of the case to the hinge should match the original (usually 2-3 cm).
• 🔩 Tighten the screws, but not all the way - leave some play for adjustment.

For the lower loop:

• 🔧 On some models (KG39FBI30) the lower loop has adjusting bolt for height alignment. Don't lose it!
• 🔄 If there are no holes on the other side, use a template (usually included with the refrigerator). If there is no template, measure and transfer the markings manually.

For models with hidden hinges (for example, Siemens StyleCollection) the process is more complicated:

Features of hidden hinges

Hidden hinges are attached inside the body and door. To remove them you will need:

1. Dismantle the decorative panel on the door. (snap off the clips).

2. Unscrew the screws holding the inside of the hinge.

3. Move the fastenings to the other side, maintaining symmetry.

Attention: without experience, it is better not to take risks - a mistake will lead to irreversible damage to the panel.

4. Installing the door on the new side

This is the most critical step:

1. Put the door on. on lower hingealigned in the center. Make sure that the hinge pin fits into the groove.

2. Lift the door and place the upper part on the upper hinge. You will need an assistant or fix it with a magnet.

3. Tighten it. screws of the top hinge, but do not tighten completely.

4. Check gaps along the perimeter of the door - they should be the same (2–4 mm).

For models with freezer compartment at the bottom (for example, KG39NVI30):

• 🔄 First, the freezer door is installed, then the refrigerator door.
• 🔧 There should be a gap of 5-7 mm between the doors for free movement.

After preliminary installation:

• 📏 Measure the diagonals of the door (from corner to corner) - they should match. If the difference is more than 5 mm, adjustment is required.
• 🔧 Tighten the screws, starting with the top hinge, then the bottom.
• 🧴 Apply silicone grease to the hinge axes for smooth operation.

5. Adjusting and checking tightness

Even a perfectly installed door may require final adjustment. Check:

• 🔍 Seal fit: place a strip of paper between the door and the body. If it falls out or is pulled out too tightly, adjustment is needed.
• 📉 Door level: use a bubble level. A misalignment of more than 2 mm will lead to spontaneous opening.
• 🔊 Sound when closing: the cotton should be uniform. A dull knock or creaking indicates a problem.

For adjustment:

• 🔧 Top hinge: responsible for the tilt of the door. Loosen the screws and move the door in the desired direction.
• 🔩 Bottom hinge: adjusts the height. Tighten the bolt clockwise to lift, counterclockwise to lower.

If the seal is deformed or torn during dismantling, it will have to be replaced. For Siemens original elastic bands with article numbers are suitable: 00602356 (for models 60 cm wide) or 00602357 (for 70 cm).

6. Typical mistakes and how to avoid them

Errors when hanging doors Siemens can result in serious problems. Let's look at the most common ones:

• 🔧 Overtightened hinge screws → door deformation or thread breakage.

  Solution: Tighten the fasteners gradually, checking the door movement after each turn of the screwdriver.

• 🚪 Mismatch of holes on a new one side.

  Solution: Use the template from the kit or drill new holes according to the markings (drill diameter - 4–5 mm).

• 🔄 Confusion loops upper and lower doors.

  Solution: The hinges are marked - there is usually a mark on the top TOP or UP.

• 🧲 Ignoring the magnetic seal.

  Solution: After installation, warm the seal with a hairdryer (temperature 50–60°C) to restore elasticity.

Another common problem is creaking hinges after overhanging. Reasons:

• Lack of lubrication on the axles.
• Door misalignment.
• Debris getting into the mechanism.

To eliminate:

1. Remove the door and clean the hinges from dust.
2. Apply silicone grease (do not use WD-40 - it is aggressive for plastic!).
3. Adjust the position of the door.

⚠️ Attention: If after rehanging the refrigerator Siemens became make more noisecheck:

• Are the transport bolts secured (on models with a compressor Inverter).
• Does the door touch internal shelves when closing.
• Are the compressor fastenings loose (vibration can be transmitted to the housing).

7. Features for refrigerators with a display

Models Siemens with electronic control (series iQ500, iQ700) require additional manipulations:

• 📱 Moving the control panel: on some models the display is attached to the door. It must be carefully removed, disconnect the cable and fasten it to the new side.
• 🔌 Reset errors: after re-hanging, the indicator may light up E1 or E2 (tightness failure). Reset them by holding the button On/Off 10 seconds.
• 🔄 Sensor calibration: in the service settings menu (access via SuperCool + SuperFreeze) select item Door Calibration.

For models with touch screen (Siemens Home Connect):

• 📱 Before removing the door, turn off the power and wait until the display turns off completely (30–60 seconds).
• 🔧 The display cable is fixed with a latch - do not pull it by the wires!
• 🔄 After installation, reset to factory settings (Settings → Reset).

How to reset E1 error on Siemens iQ700

1. Press and hold the button SuperCool 5 seconds.

2. Using the buttons +/– select the menu item d 01.

3. Press OK and wait for the reboot. (about 1 minute).

If the error remains, check the tightness of the seal with a test with a paper strip.

8. When is it better to contact a specialist

Not all situations can be solved independently. Contact the service center Siemensif:

• 🔧 There are no symmetrical holes for hinges on the body or doors.
• 🚪 The door opens on its own after rehanging data-i="260">🔌 Appeared (balancing problem).
• 🔌 Appeared electrical faults (the display does not work, the indicators are blinking).
• 🔊 The compressor noise has increased or vibration has appeared.
• 🧊 Refrigerator stopped maintain the temperature (freon may leak if the tubes are damaged).

Cost of professional door hanging in service centers Siemens (in Moscow and regions for 2026):

If you decided to act on your own, but something went wrong so do not try to “finish” the work - the risk of damaging the refrigerator is higher than saving. For example, breaking the thread in the hinge will entail replacing the entire door (and this is 15-30 thousand rubles for models Siemens).

⚠️ Attention: Warranty for refrigerators Siemens does not apply to damage caused by self-repair. If the device is under warranty, it is better to call a technician from an authorized service center.

FAQ: Frequently asked questions about re-hanging doors

Is it possible to re-hang the door on a Siemens refrigerator without assistant?

Theoretically, yes, but this is risky. The doors weigh 10–20 kg (depending on the model), and it is difficult to hold them with one hand during installation. For models with a freezer at the bottom (KG39), an assistant is required - the lower door is heavier than the upper one.

If there is no assistant, use adjustable stops or magnetic latchesto temporarily secure the door in the desired position.

What to do if, after rehanging, the door does not close tightly?

Causes and solutions:

• 🔧 Distortion of the hinges → Adjust the height and tilt of the door.
• 🧲 Deformation of the seal → Warm it with a hairdryer or replace it.
• 🚪 Debris getting into the hinges → Clean and lubricate the mechanism.
• 🔄 Magnet mismatch → Check the polarity (there are marks on the seal N/S).

If the problem persists, check body geometry —maybe the refrigerator is not level.

Do you need to defrost the refrigerator before rehanging?

Required if:

• You are working with freezer compartment (risk of damage to the tubes during dismantling).
• Refrigerator NoFrost, but there is ice on the seal (it interferes with accurate installation).

For models with drip system (for example, KG36NXA30) defrosting is not necessary if you do not touch the freezer.

Is it possible to hang the door on a Siemens refrigerator with an integrated handle?

Yes, but the process is more complicated:

1. Remove the handle (usually it is secured with latches or screws under the decorative panel).
2. Move the handle fastenings to the other side (the holes must match).
3. Install the door and secure the handle in the new one position.

On models StyleCollection the handle may be asymmetrical - in this case it will have to be replaced (the part number is indicated in the instructions).

How often can you rehang the doors without damaging the refrigerator?

Technically — 2-3 times without consequences if:

• Original hinges and seal are used.
• The holes are not loose (do not increase with each dismantling).
• Not applicable excessive force when tightening the screws.

Frequent overweighting leads to:

• 🔧 Wear of the threads in the hinges.
• 🧲 Loss of elasticity of the seal.
• 🚪 Door deformation (especially for models with thin metal).