Modern kitchens often dictate their own rules of ergonomics, forcing home appliance owners to look for ways to optimize space. Refrigerators Beko are initially designed with the ability to change the opening side, which makes them a flexible solution for any layout. However, the rehanging process requires care, since door hinges and the closing mechanism are units subject to high mechanical load.
Before starting work, you must clearly understand the design of your unit. In most models Beko re-hanging is carried out without completely disassembling the body, but requires removing decorative plugs and rearranging fasteners. In two-chamber models, the upper and lower doors often have different hinge designs, which requires care when rearranging them. Incorrect installation can lead to misalignment and loss of tightness.
You should not ignore the preparatory stage, since the success of the entire operation depends on it. You will need free space around the refrigerator and a stable base. If this is your first time encountering such a task, take your time and carefully study the sequence of actions to avoid damage to seals or plastic elements.
Necessary tools and preparation of the workplace
High-quality work is impossible without the appropriate tools. The basic set usually consists of items that are found in every home, but some models Beko may require specific keys. Prepare everything you need in advance so as not to interrupt the search process.
Pay special attention to the choice of screwdrivers. Screw slots in household appliances are often soft, and the use of low-quality tools can lead to licking the caps. In this case, it will be extremely difficult to remove the fasteners without drilling.
- 🔧 Medium-sized Phillips screwdriver (PH2) for the main screws.
- 🔧 Slotted screwdriver for removing decorative panels.
- 🔧 8 mm open-end or socket wrench (often required for hinges).
- 🔧 Construction level for checking horizontal position.
- 🔧 Spatula or plastic spatula for carefully removing plugs.
⚠️ Attention: Before starting any work, be sure to disconnect the refrigerator from the power supply! This is critical for safety as you will be working with metal in close proximity to electrical components and wiring.
Dismantling the top door and removing decorative elements
The process begins from the top of the refrigerator. First you need to free access to fasteners hidden by decorative plugs. They can be located at the end of the door or on the top panel of the case, depending on the specific series Beko.
Carefully pry up the plastic covers with a slotted screwdriver. Do not use excessive force to avoid breaking the fasteners. Underneath the caps you will find screws holding the top hinge in place. They need to be unscrewed, but not removed completely yet, if the door is not yet secured by an assistant.
To remove the door, it is best to call a second person who will hold the heavy structure. After unscrewing the fasteners, the top hinge is removed and the door is carefully set aside. At this stage, it is important not to damage capillary tubeif it passes through the hinge, although in modern models Beko it is often hidden inside the case.
Rearranging hinges and fittings
The most important stage is the transfer of metal elements to the opposite side. The design of refrigerator hinges Beko is symmetrical, but requires correct orientation. Carefully inspect the removed parts: they are often marked "Top" (top) and "Bottom" (bottom) or directional arrows.
First move the hinge pin on the bottom of the door. This may require removing the plastic stop. Then install the top hinge in its new location using the same holes but on the other side. Make sure that the rotation axis fits neatly into the slot intended for it.
- 🛠️ Remove the plugs from the holes on the opposite side of the case.
- 🛠️ Move the stoppers and bushings to new places according to the diagram.
- 🛠️ Install the hinges, making sure that they fit tightly to the body.
- 🛠️ Fix the fasteners, but do not tighten them all the way yet.
⚠️ Attention: Do not confuse the length of the screws! The design of the refrigerator can use fasteners of different lengths for the upper and lower units. Using a long screw in a short hole may cause damage to the cooling system. damage to the internal chamber. What to do if the holes do not line up? or cooling systems.
What to do if the holes don't match?
Some Beko models require rearranging the plastic bushings inside the housing holes to re-hang them. If the screw does not fit, check whether the internal plastic part is in the way, which needs to be turned over or moved to the other side.
Installing doors and adjusting gaps
After preparing the hinges, you can begin hanging the doors. The lower door is installed first, then the upper one. It is important to ensure that the hinge axes fit exactly into the mating parts on the doors. Skewing at this stage is unacceptable.
Secure the doors with screws. At this stage it is recommended to use building levelto check the verticality of the installation. If the refrigerator is not level, adjust the height of the front legs of the case by unscrewing or tightening them.
| Element | Action | Control parameter |
|---|---|---|
| Bottom hinge | Axle fixation | No backlash |
| Upper hinge | Attachment to the body | Parallel to the roof |
| Seal | Checking fit | Uniform gap |
| Refrigerator legs | Height adjustment | Horizon level |
Closing density is a key indicator of successful reweighing. The door should close on its own when opened at an angle of about 45 degrees, thanks to the magnetic lock and the slight tilt of the body back. If the door slams or, conversely, does not reach the end, additional adjustment is required.
☑️ Checking the installation quality
Nuances for models with the No Frost system
Refrigerators Beko s systems No Frost have a more complex design of air ducts. When rehanging doors in such models, it is often necessary to rearrange plastic flaps or air ducts, which can be attached to the inside of the door.
Carefully inspect the inside door panel. If you see holes or fasteners on the opposite side, this means that the elements of the air circulation system need to be rearranged. Ignoring this step will result in malfunction of the defrost system and improper distribution of cold.
In some cases, it is necessary to remove the inner plastic door panel to gain access to hidden fasteners or channels. Do this carefully, as plastic becomes brittle at low temperatures. Allow the refrigerator to reach room temperature before removing the panels.
⚠️ Attention: In models with a display on the door, additional steps may be required to transfer cables or rearrange the control module. If you are not confident in your abilities, it is better to contact a service center so as not to damage electronics.
Final check and testing
After completion of installation and visual inspection, it is necessary to conduct testing. Plug in the refrigerator and let it run idle for at least 2-3 hours. During this time, you will be able to evaluate the quality of work and the absence of extraneous noise.
Check the tightness of the seal around the entire perimeter. To do this, you can use a simple test with a sheet of paper: hold the sheet with a door and try to pull it out. It should be removed with noticeable resistance along its entire length.
- 👀 Visually inspect the gaps between the door and the body.
- 👀 Make sure that the shelves do not touch the door when closing.
- 👀 Check the operation of the magnetic lock at different points perimeter.
- 👀 Make sure that the decorative elements are installed smoothly.
If you notice that the door does not fit tightly in one of the corners, you may need to fine-tuning the position of the refrigerator by tightening the adjustable legs. Small distortions of the floor can significantly affect the closing geometry of heavy doors.
Why does the door not close completely?
A common reason is a protruding edge of a shelf or a bottle that prevents it from closing tightly. Also check that the opening limiters at the end of the door are installed correctly.
Frequently asked questions (FAQ)
Do you need to defrost the refrigerator before hanging the doors?
Full defrosting is not necessary if you work quickly. However, if you plan to remove interior panels or air ducts (in No Frost models), it is better to first turn off the refrigerator and let the ice melt so that moisture does not get on the electrical contacts.
Is it possible to hang the doors alone, without an assistant?
Technically this is possible, but it is highly not recommended. Refrigerator doors Beko are heavy and have complex geometry. You should not drop them - the internal plastic insert may burst or the case may become deformed. It is better to enlist the help of a second person.
What to do if, after rehanging, there are excess fasteners left?
The refrigerator usually comes with a set of plugs for holes that are not used in the current configuration. If the fasteners remain from the hinges, it means they were not fully installed. It is better to keep the extra screws and plugs in a bag with instructions in case of reverse rearrangement.
Does rehanging the doors affect the warranty?
Independent rehanging of the doors, provided for by the design and instructions Bekodoes not void the warranty. However, if in the process the hinges, plastic or the case are damaged, the service center may refuse to repair these specific damages free of charge.