We rehang the door of the Candy refrigerator with our own hands: instructions with photos and tips

Hanging the refrigerator door Candy is a task that frightens many users. It seems that this requires special skills or calling a specialist. In fact, the procedure takes no more than 1-2 hours if you know the key nuances. The main thing is to follow the logic of the design. In this article, we will go through step by step how to properly remove, rearrange and secure the door on models take your time and follow the logic of the design. In this article we will go through step by step how to properly remove, rearrange and secure the door on models Candy with top, bottom or side fastening, and also tell you what mistakes beginners most often make.

It is worth noting that the instructions are suitable for most modern refrigerators of the brand, including series Candy CRUZ, Candy TRIO i Candy FPP. However for older models (manufactured before 2010) there may be some peculiarities - we will warn you about this separately. If your refrigerator is under warranty, check the conditions of the service center: some manufacturers consider hanging the door to interfere with the design.

Before starting work, prepare tools and free up space around the refrigerator. You will need at least 1 meter of free space on the side where the door will open after hanging. Do not forget that the weight of the door with shelves can reach 15-20 kg - it is better to work with an assistant.

1. Preparation: tools and safety measures

To hang the door Candy you do not need professional tools - just what is in every home is enough. Here is the complete list:

• ✅ Phillips screwdriver (usually No. 2) - for most screws
• ✅ Hex wrench (size 4 or 5 mm) - for some models with hidden fasteners
• ✅ Flat screwdriver - for removing decorative plugs
• ✅ Wrench (size 10 or 13 mm) - for the lower hinges
• ✅ Making tape - to secure the door during operation
• ✅ Level (optional) - to check the evenness after installation

Before starting work be sure to unplug the refrigerator. This is not only a safety issue, but also protection of electronics: when removing the door, sensor or backlight wires may be touched. If your model has electronic display, take a photo of the current settings - after reversing, a reset may be required.

Pay special attention door fixation. To prevent it from falling when disconnected, stick it to the body of the refrigerator with masking tape or ask an assistant to hold it. For models with French door (double-leaf) the weight doubles - here you cannot do without an assistant.

⚠️ Attention: For refrigerators Candy with the system No Frost air ducts can pass through the door. When removing, do not pull the door towards you - first inspect the top hinge for the presence of plastic tubes.

Take a photograph of the location of the shelves and accessories|Unplug the refrigerator from the outlet|Free up space around (1 m)|Prepare the tools according to the list|Secure the door with tape or with an assistant-->

2. Removing decorative plugs and the top hinge

We start with the top fastening - it is usually easier to dismantle. First we remove decorative plugsthat hide the screws. They can be:

• 🔹 Plastic - pry off with a flat screwdriver
• 🔹 Rubber - pulled out by hand (sometimes with force)
• 🔹 On the latches —require gentle pressing from the side

Under the plugs you will see 2-3 screws (depending on the model). In Candy CRUZ and TRIO the combination is often used: one screw for a Phillips screwdriver + one for a hexagon. Unscrew them one by one, without removing them completely, so that the door does not fall. When the screws are loosened, hold the door and carefully remove it from the top hinge, lifting it up.

In some models (for example, Candy FPP 140) the top hinge has retaining ring. It must be removed with pliers before removing the axle. If the ring is damaged, no problem, the refrigerator usually comes with spare ones.

What to do if the screws cannot be unscrewed?

If the screws are “stuck” or rusty, use WD-40 or an equivalent. Apply the product, wait 5-10 minutes and try again. Do not use excessive force - you may strip the threads. As a last resort, contact the service center, as damaged hinges will have to be replaced completely.

3. Dismantling the lower hinge and removing the door

The lower fastening is usually more difficult than the upper one due to the weight of the door and the presence of shock absorbers or springs. The models Candy use two types of structures:

1. Removable axle —the door is removed after pulling out the pin (a hexagon is required).
2. Fixed axis —a full unscrewing the hinge from the body (with a wrench).

Algorithm of actions:

1. Make sure that the door is fixed (with tape or an assistant).
2. Unscrew the screws of the lower hinge (usually 2-3 pieces).
3. If it is decorative cover on the hinge, remove it.
4. Lift the door up and pull it towards you, removing it from the axis.

For models with water dispenser (for example, Candy CRUZ 5000) hoses pass through the bottom of the door. They need to be carefully disconnected, having first clamped the water supply (if the refrigerator is connected to the water supply). Do not pull the hoses - they are attached with plastic latches that are easy to break.

⚠️ Attention: If after removing the door you see rust on the hinges - clean it with fine sandpaper and lubricate it with silicone grease. This will extend the service life of the mechanism.

4. Transferring the hinges to the other side

Now you need to move the fastenings to the opposite side. Here it is important to consider symmetry of the holes in the refrigerator body. In most models Candy holes for hinges are already provided on both sides, but they are closed with plugs. Your task:

• 🔧 Remove the plugs on the opposite side (similar to the top ones).
• 🔧 Transfer the hinges by unscrewing them from the body and screwing them in a mirror.
• 🔧 Check if the holes for the shock absorbers match (if any).

The table below shows typical fastening patterns for different series Candy:

If your model has shock absorbers located on only one side, they need to be moved to the opposite side. To do this:

1. Remove the shock absorber mount from the door and body.
2. Install it in a mirror image using the existing holes.
3. Adjust the tension (if the shock absorber is spring).

5. Installing the door on the new side

When the hinges have been moved, you can hang the door back. Start with the bottom fastening:

1. Place the door onto the bottom hinge axle, making sure it goes in all the way.
2. Hold the door, screw in the screws of the bottom hinge (do not tighten it all the way!).
3. Lift the door and put it on the upper hinge.
4. Tighten the screws of the upper hinge, then finally fix the lower ones.

After installation, check:

• 🔸 Closing —the door should fit evenly around the entire perimeter.
• 🔸 Opening angle —if the door opens too easily or too tightly, adjust the shock absorbers.
• 🔸 Glitches —gaps of more than 2 mm indicate incorrect installation of the hinges.

If door does not close tightly, the reasons may be the following:

• ❌ The hinges are not tightened evenly.
• ❌ The rubber seal is dirty or deformed.
• ❌ The refrigerator is not level (check the level).

6. Adjusting and checking the tightness

The final stage is adjusting the hinges checking the tightness. Start with the adjustment:

1. Open the door to 45° and check if it remains in this position. If it falls, loosen the top screws and adjust the tension.
2. Close the door and pull the handle: if resistance is felt, the hinges are tightened too tightly.

To check the tightness, use test with a sheet of paper:

1. Insert a sheet of paper between the seal and the body.
2. Close the door and try to pull out the sheet.
3. If the paper comes out easily, the seal does not fit. You need to adjust the loops or clean the elastic.

If the seal is dirty, wash it with warm water and soap and dry it. To restore elasticity, you can use silicone grease (do not confuse with WD-40!). Apply it in a thin layer on a dry rubber band.

⚠️ Attention: For refrigerators Candy with electronic control, the opening sensor may go astray after reversing the door. If the "door open" indicator is constantly on, check the position of the magnet in the seal.

7. Common mistakes and how to avoid them

Even with careful work, you can make mistakes that will lead to breakdown. Here are the most common:

• 🚫 Tightening the screws — leads to thread failure or hinge deformation. Tighten all the way, but without excessive force.
• 🚫 Ignoring shock absorbers —if you do not move them, the door will close with a blow.
• 🚫 Damage to the seal —do not pull the rubber band when removing the door, it breaks easily.
• 🚫 Incorrect position of the hoses (in models with a dispenser) - can lead to leaks.

If after rehanging the door opens spontaneously, the problem lies in:

• ➡️ Uneven floor —adjust the legs of the refrigerator.
• ➡️ Hinges that are too tight —loosen the top screws.
• ➡️ Worn seal require replacement.

For models with No Frost system after re-hanging, cooling may temporarily deteriorate. This is normal: the refrigerator needs 12-24 hours to restore air circulation. If after a day the temperature has not returned to normal, check whether the air duct is jammed in the door.

8. Features for different Candy models

Although the principle of hanging the door is the same, some series Candy have nuances:

• 🔧 Candy CRUZ —the top hinge has hidden screw under the brand logo. To get to it, carefully pry off the sticker.
• 🔧 Candy TRIO —the bottom hinge is attached to four screws, and not three, as in most models.
• 🔧 Candy FPP —included spare plugs for hinge holes. Don’t lose them!
• 🔧 Candy CBO —the door has additional lock in the middle part, which must be moved along with the hinges.

For refrigerators with French door (double-leaf) the procedure is more complicated:

1. First, the upper small door is removed.
2. Then the lower large one.
3. The loops are transferred in pairs, maintaining the sequence.

If your model is equipped with touch panel on the door (for example, Candy Smart Touch), before removing, turn off the power and wait until the display turns off completely. After rehanging, you may need to sensor calibration —instructions are in the user manual.

FAQ: Answers to frequently asked questions

Is it possible to hang the Candy refrigerator door yourself if you have no experience?

Yes, the procedure does not require special skills. The main thing is to follow the instructions, use the right tools and work with an assistant (the door is heavy). If in doubt, practice unscrewing and tightening the screws without removing the door.

What to do if the door does not close after rehanging?

Check:

1. The evenness of the installation of the hinges (they must be symmetrical).
2. Condition seal - it may be dirty or deformed.
3. The level of the refrigerator - the legs should be level.

If the problem remains, loosen the hinge screws and adjust the position of the door.

Is it necessary to rehang the internal shelves after changing the opening side?

No, the internal shelves and drawers remain in their places. An exception is models with asymmetrical door shelves (for example, bottle holders). They can be rearranged in a mirror order for convenience.

Can reversing the door affect the warranty?

Depends on the terms of the warranty. Some service centers consider this to be interference with the design. If the refrigerator is under warranty, check with the official dealer for details. Candy.

How often should the hinges be lubricated after rehanging?

Once every 1-2 years is enough. Use silicone grease (not petroleum-based oils!). Apply it to the hinge axes, having first cleared them of dust.