Repositioning the Haier refrigerator door: instructions with photos and videos

Re-hanging the refrigerator door Haier is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Unlike European brands, Chinese refrigerators (including Haier, Hisense or Midea) often have unique fastenings, which require a special approach. In this article we will analyze step-by-step instructions taking into account the nuances of specific models, a list of tools and typical errors that lead to door misalignment or damage to the seal.

Important: the procedure for Haier differs from refrigerators Samsung or Atlant —hidden fastenings under decorative plugs are often used here, and some models (for example, series HRF or CBD) require dismantling the top panel. If your refrigerator is under warranty, rehanging the door may invalidate it check this with the service center before starting work.

We have collected the experience of craftsmen and user reviews to create the most complete guide possible. At the end of the article - FAQ on problems (creaks, loose fit, adjusting hinges) and video instructions for a visual understanding of the process.

1. Preparation: tools and conditions

Before hanging the door, prepare your workspace and tools. Haier uses hexagon mounts (usually 4 mm or 5 mm), so a standard screwdriver may not be suitable. Here is the complete list:

• 🔧 Hex key (4 mm and/or 5 mm -depends on the model)
• 🔨 Phillips and flathead screwdrivers (for removing plugs)
• 📏 Tape measure or ruler (for checking gaps)
• 🧲 Magnet or telescopic grip (so as not to lose screws in hard-to-reach places)
• 🧴 Silicone grease (for hinges after rehanging)
• 🧽 Soft cloth and alcohol (for cleaning the seal)

Required condition: the refrigerator must be empty and disconnected from the network at least 2 hours before the start works This is necessary for:

• ❄️ Preventing condensation on the seal (wet rubber can be deformed during dismantling).
• ⚡ Eliminating the risk of short circuit (even if you are not working with electrical, it’s better to play it safe).
• 🔄 Convenience - an empty refrigerator is easier to tilt to access the lower hinges.

⚠️ Attention: If your Haier equipped with a display or electronic control (models HRF-618, CBD-535 etc.), after rehanging it can required reset settings through the menu Settings → Factory Reset. Take a photo of the current temperature settings in advance.

2. We determine the model and type of fastenings

Haier produces refrigerators with three types of hinges:

1. Hidden hinges under plugs (most common in models HRF, HBF).
2. Open hinges with decorative caps (series CBD, HRT).
3. Combined (the upper hinge is hidden under the panel, the lower one is open).

To accurately determine the type, inspect the side walls of the refrigerator:

• 🔍 If you see plastic plugs with latches - you have hidden hinges.
• 🔍 If the hinges are visible, but closed with round caps - open with decor.
• 🔍 If there is a solid panel on top without visible fasteners — combined type.

Critical detail: in models Haier with system No Frost (for example, HRF-618SS) after rehanging, it may be required reinstallation of the door closing sensor. It is located on the top hinge and is responsible for the door open signal.

How to find out the series of your model?

The series is indicated on the nameplate (metal plate) on the back of the refrigerator. For example, in the model Haier HRF-618SS series - HRF, and 618 —volume in liters. If the nameplate is erased, look in the documents or in the refrigerator menu: Settings → Device information

3. Step-by-step instructions: removing the door

The process of dismantling the door depends on the type of hinges. Let's consider the most difficult option - hidden hinges under the plugs (relevant for most models HRF and HBF).

Step 1. Remove the plugs.

1. Pry the plastic plug on the top hinge flat with a screwdriver. The movement must be careful not to break the latches.
2. In the same way, remove the plug from the bottom hinge. In some models it may be glued - use a hair dryer to heat the glue (temperature no higher) 50°C).

Step 2. Unscrew the top hinge.

1. Use a hexagon 4 mm unscrew the two screws holding the hinge. Do not remove them completely - loosen enough for the hinge to come out of the groove.
2. Hold the door so that it does not fall. In models with a display on the door (HRF-618DG), first disconnect the power cable (the connector is usually located under the top hinge).

Step 3. Remove the door from the bottom hinge.

1. Lift the door up to remove it from the bottom pin. If the hinge is tight, slightly rock the door from side to side.
2. Put the door on the prepared fabric face upto avoid damaging the seal.

Step 4. Removing the lower hinge.

Unscrew the hex screws 5 mm and remove the hinge. Pay attention to adjusting washers —their position affects the tightness of the door after installation!

4. loops to the other side

Now you need to move the loops to the opposite side. Here it is important to observe symmetry and not confuse the top hinge with the bottom - they may look the same, but have different loads.

Step 1. Preparing the holes.

• On the opposite side of the refrigerator you will see plugs covering the technological holes for hinges. Remove them in the same way as before.
• Check that the holes match the hinges. In models Haier sometimes it is required drill new ones (for example, in a series CBD-535). Use a drill and template from the old hinge. Drill new ones. data-i="192">on the new side, without fully tightening the screws. Make sure that the hinge pin is facing up. 4.5 mm and a template from an old loop.

Step 2. Installing hinges.

1. Secure lower hinge on the new side without fully tightening the screws. Make sure the hinge pin is facing up.
2. Install the upper hinge in the same way. In models with a display, do not forget to thread the cable through the hole in the hinge.
3. Check gaps: there should be uniform clearance between the door and the body 2–3 mm along the entire perimeter.

Step 3. Adjustment.

After preliminary installation of the door, adjust its position:

• 🔧 If the door is sags - tighten the screws of the bottom hinge.
• 🔧 If does not fit tightly on top — loosen the top hinge and slide the door down.
• 🔧 If creaks —apply silicone grease to the hinge pins.

⚠️ Attention: In refrigerators Haier s automatic ice maker (models HRF-6xxA) after rehanging it may required resetting the water supply. The supply tube is located behind the top hinge - do not damage it when dismantling!

5. Checking and troubleshooting

After rehanging the door, check:

1. Seal tightness: take a sheet of paper, insert it between the seal and the body and close the door. If the sheet is pulled out without effort, the seal requires adjustment.
2. Gap uniformity: visually inspect the clearance around the entire perimeter. Permissible play - no more 3 mm.
3. Sensor operation: in models with a display, make sure that the door closed indicator goes off (if not, check the sensor contacts).

Typical problems and their solutions:

If after adjusting the door still remains does not close tightly, the reason may be a deformed seal. In this case:

1. Remove the seal (it is attached with latches or glue).
2. Immerse it in hot water (60–70°C) for 10 minutes, then shape it.
3. Glue it back using silicone sealant (do not use superglue!).

6. Features for Side-by-Side refrigerators

Models Haier with two doors (HS-5xx, HSC-6xx) require simultaneous rehanging of both doorsas they are connected by a common top panel. There are several nuances here:

• 🔧 The top panel secured with 4 torx screws T20Remove it before removing the hinges.
• 🔧 Close sensor is located on the middle jumper - do not damage it when removing the panel.
• 🔧 Lower hinges have a reinforced design. To dismantle them you will need long hexagon (at least 10 see).

Procedure:

1. Remove the top panel by unscrewing the 4 screws T20.
2. Disconnect the display power cables (if any).
3. Remove the hinges one by one, starting from left door (it usually contains a freezer compartment, and it is heavier).
4. When installing hinges on the new side, use levelso that the doors are strictly parallel.

Important: Side-by-Side after re-hanging be sure to check the synchronicity of closing. If one door closes before the other, adjust the stops on the hinges.

7. materials

For a visual understanding of the process, we recommend that you familiarize yourself with the video tutorials. Below is a selection of videos for different series Haier:

• 📺 Rehanging the door on Haier HRF-618 (hidden hinges).
• 📺 Door adjustment Haier CBD-535 (open hinges).
• 📺 Moving hinges to Haier Side-by-Side HS-523.

It is also useful to study:

• 📄 Official guide Haier on maintenance (section "Door Adjustment").
• 📄 Catalog of spare parts for Haier (articles of hinges and seals).

⚠️ Attention: In the instructions for refrigerators Haier after 2020, it may be indicated that the door can be re-hung is only possible at the service center. This is associated with a risk of damage to the system Smart Inverter (in models with compressors Twin Inverter). Check this point in the documents for your model.

8. Frequently asked questions (FAQ)

❓ Is it necessary to defrost the refrigerator before re-hanging the door?

Yes, required. No Frost on the models, condensation can accumulate on the seal, which, when dismantling the door, will get inside the case. hours before work, remove all food and wipe the seal with a dry cloth.

❓ Is it possible to hang the door on the refrigerator Haier with a display yourself?

It is possible, but care is required when working with power cable. In models HRF-618DG or CBD-535W the cable passes through the top hinge - it must be disconnected before removing the door. After rehanging, check that the connector is firmly seated in the socket (a click should be heard).

❓ What to do if the door creaks after rehanging?

The creaking occurs due to:

1. Dry hinges — lubricate the pins silicone grease (do not use WD-40 or oils!).
2. Warp - loosen the screws of the hinges and adjust the position of the door.
3. Deformed seal - warm it with a hairdryer (40–50°C) and press the door for 1–2 hours.

If the creaking does not disappear, check rubber gaskets on the hinges (they could have moved during dismantling).

❓ How to rehang a door if there is no hex key?

Instead of a hexagon, you can use:

• Torx wrench of a suitable size (for example, T15 or T20).
• A screwdriver with a hexagon bit (sold in furniture sets).
• Homemade wrench from a bolt and a nut (clamp the bolt in a vice and file the edges for a hexagon).

⚠️ Do not use pliers - they will tear off the edges of the screws!

❓ Why did the refrigerator become louder after rehanging?

This is due to:

1. By changing the center of gravity — if the door is heavier on one side (for example, due to the ice maker), vibrations during compressor operation increase. Solution: adjust the legs of the refrigerator.
2. Loosening the compressor fastenings — when the refrigerator was tilted, they could move. Check the screws on the back wall.
3. Damage to the refrigerant tubes - if you accidentally touched them when re-hanging, a microcrackcould form. In this case, you need a specialist.