How to hang the door on an LG refrigerator: instructions with photos and video

Reversing the door refrigerator LG is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Unlike models from other brands, equipment from the Korean manufacturer has its own design features: hidden fasteners, specific hinges and, in some series, integrated water dispensers. Without preparation, the process may seem complicated, but with the right approach you can handle it in 1-2 hours.

The main advantage reweighing yourself is saving on calling a specialist (on average from 1,500 to 3,000 rubles). However, it is important to consider that not all models LG support this option. For example, in refrigerators with a system Door-in-Door or some two-chamber versions with French Door it is almost impossible to rehang the door without damaging the body. In this article, we will look at step-by-step instructions, nuances for different series and typical mistakes that lead to distortions or breakages.

Preparation: tools and checking model compatibility

Before you start work, make sure that your model LG generally supports overweighting. This information is indicated in operating instructions (section “Installation” or “Installation”). If the documentation is lost, check:

• 🔍 The presence of plugs on the opposite side of the case (usually closed with decorative covers).
• 📏 Symmetry of holes for hinges on both sides of the refrigerator.
• ⚙️ Hinge type: in models with No Frost reinforced fasteners are often used, requiring a special key.

If at least one of these signs is missing, the door not intended for hanging. An attempt to do this by force will lead to damage to the seal or plastic case.

The tools you will need:

⚠️ Attention: In refrigerators LG with a water dispenser (series LRMVC, LRMXC) before rehanging, you must turn off the water supply and drain the remaining residue from the tube. Ignoring this step will lead to leaks!

Removing the old door: step-by-step process

Start by unplugging the refrigerator from the mains. Next, follow the algorithm:

1. Remove decorative plugs from the top and bottom loops. In most models, they are fixed with latches - pry them off from the side with a plastic spatula. In series GA-B and GB-B the plugs can be secured with screws (for a Phillips screwdriver).

2. Unscrew top hinge. In refrigerators LG it is usually fixed with 2-3 screws. Hold the door so that it does not fall after removing the fastening!

3. Carefully remove the door from lower hinge. In models with No Frost the hinge can be equipped with a spring - do not pull the door towards you, but lift it up at an angle of 45°.

   .

4. Disconnect display power cable (if any). In refrigerators with electronic control (series InstaView), the connector is located under the top hinge. Remember the position of the contacts or take a photo.

Pay special attention seal. It is easy to damage during dismantling. If the rubber is deformed or torn, replace it to installing the door on a new side. original seals for LG are marked with a code that can be found on the old part (for example, ADQ72916601).

All decorative plugs have been removed|Hinges have been unscrewed (top and bottom)|Cables have been disconnected (if there is a display)|The seal is intact and clean|New holes have been prepared for fastenings-->

Features of rehanging for models with No Frost and dispenser

Refrigerators LG with system No Frost (series GA, GB, GC) have reinforced hinges and additional fasteners to evenly distribute the weight of the door. Here are the key nuances:

• ❄️ Ventilation grilles: In models with Multi Air Flow when re-hanging, you need to redirect the air flow. To do this, remove the inner lid of the freezer and reinstall the deflectors (plastic guides).
• 💧 Water/ice dispenser: In series LRMVC23* i LRMXC25* the water supply tube passes through the door. You will have to:
• Disconnect the water hose.
• Drain the water from the system (press the dispenser button for 30 seconds).
• Reinstall the tube on the opposite side (plugs for unused holes are included).
• ⚡ Electronic modules: In refrigerators with a touch screen display (InstaView Door-in-Door) after rehanging it is required reset settings. To do this, press the buttons Power Cool and Power Freeze for 10 seconds.

For models with Linear Cooling (uniform cooling technology) after rehanging, it is recommended to run temperature calibration. This is done through the service menu:

1. Disconnect the refrigerator from the network for 1 minute.
2. Turn on and immediately press the combination: Door Alarm + Freezer (hold for 5 seconds).
3. In the menu, select Calibration → Start.

⚠️ Attention: In refrigerators LG s function Smart ThinQ After re-hanging the door, you may need to reconnect to Wi-Fi. If the indicator flashes red, reset the network settings in the mobile application.

Installing the door on a new side: step by step

Now let's move on to installation. Follow the instructions strictly in order:

1. Install the lower hinge to the opposite side. In models LG there are usually already holes for it (closed with plugs) If there are no holes, you will have to drill them, but this is risky (you can damage the freon). highway).

2. Place the door onto the lower hinge, holding it by the upper edge. Make sure that the hinge fits into the groove until it stops.

3. Pin top loop. Do not tighten the screws all the way - first check that the door hangs evenly. Use a level!

4. Connect power cables (if there is a display). Polarity is important - follow the mark + and – on the connector.

5. Install decorative plugs to new holes. They should go in with a slight click.

After installation, check:

• 🔄 Tightness of the seal: place a sheet of paper between the door and the body. If it falls out, adjustment is needed.
• 📉 Closing evenness: the door should be “attracted” by the magnet of the seal, and not close with force.
• 🔊 Absence of extraneous sounds: creaking or knocking indicates skewed hinges.

Adjusting the hinges and seal after rehanging

Even with careful installation, the door may sag or close poorly. This can be corrected by adjustment:

For models without No Frost:

• 🔧 Loosen the screws on top hinge and slightly move the door in the desired direction.
• 📐 Check the gaps around the perimeter - they should be the same (1-2 mm).

For models with No Frost:

• 🔧 Use hexagon to adjust the lower hinge (the screw is located under the decorative cover).
• ⚖️ If the door is skewed vertically, tighten the top screw and loosen the bottom (or vice versa).

The seal may lose elasticity over time. To restore its properties:

1. Wash the rubber band with warm water and soap.
2. Apply silicone grease (without alcohol!).
3. Warm up the seal with a hairdryer (temperature no higher than 50°C) and shape it with your hands.

If the seal still does not hold, it will have to be replaced. For LG original parts with article numbers are suitable:

• ADQ72916601 - for single-chamber models.
• ADQ72916602 - for two-chamber (upper chamber).
• ADQ72916603 - for two-chamber (lower chamber).

⚠️ Attention: B refrigerators LG with the function DoorCool+ (fast door cooling) after adjusting the hinges, an error may occur Er IF. To reset it, turn off the refrigerator for 5 minutes.

Typical mistakes and how to avoid them

Even experienced craftsmen sometimes make mistakes when rehanging doors LG. Here are the most common ones:

Another common problem is the door is skewed after installation. It occurs if:

• 🔨 The screws are not tightened evenly.
• 📦 The door is hung by one person (an assistant is needed for support).
• 🔄 The weight of shelves and products is not taken into account (before rehanging, it is better to empty the refrigerator).

If the door still does not close tightly after adjustment, check:

• 🧲 Magnetic tape in the seal - it could have moved.
• 📏 Case geometry: in old refrigerators LG (until 2015) sometimes “drives” the metal frame.

What to do if, after rehanging, the refrigerator does not turn on?

If the refrigerator does not respond to being plugged in, check:

1. Fuse in the plug (sometimes burns out during a short circuit).

2. Display cable - if it is connected incorrectly, the control unit may be blocked.

3. Surge protector (on some models there is separate reset button on the rear panel).

If the problem persists, the control board is probably damaged. In this case, it is better to call a specialist.

When it is better to call a specialist: 5 signs

Despite the apparent simplicity, some situations require professional intervention. Contact the service center LGif:

1. Refrigerator with system Door-in-Door (series LRMVC236*, LRMXC2506*). It is impossible to re-hang such a door without special tools - the risk of damage to the internal mechanisms is too high.

2. After re-hanging, error Er FF or Er dH (failure in the defrosting system or humidity sensor) appeared.

3. The door sags by more than 5 mm after adjustment is a sign of wear on the hinges.

4. The refrigerator stopped freezing or vice versa, began to work without stopping.

5. You discovered cracks in the body after dismantling the hinges.

Cost of professional re-hanging in official service centers LG starts from 2,000 rubles (for simple models) and goes up to 5,000 rubles (for Side-by-Side with a dispenser). However, if the refrigerator is under warranty, Independent repair will cancel it. Check the deadline in the documents!

In Moscow and St. Petersburg you can call a specialist through:

• 📞 Official service LG (telephone number is listed in the warranty coupon).
• 🌐 Aggregators such as "RemBytTech" or "VseMasters" (average rating of the performer is 4.8+).

⚠️ Attention: When ordering a master, check whether he has experience working specifically with LG. Some models (for example, GA-B489) have non-standard fastenings, and not every specialist is familiar with them.

FAQ: Frequently asked questions about hanging LG doors

Is it possible to hang the door on an LG refrigerator with a dispenser on your own?

Yes, but it is more difficult than in conventional models. You will need:

1. Turn off the water and drain the remaining residue from the tube.
2. Redirect the water supply hose to the other side (plugs are included).
3. Reconnect the display cable (if any).

Without experience, it is better to contact the service - errors when working with plumbing system can lead to leaks.

How long does re-hanging take?

On average - 1-2 hours if:

• There is an assistant.
• Tools are prepared in advance.
• The model is not equipped with No Frost or a dispenser.

For complex models (for example, LRMVC23626S) it may take up to 3-4 hours.

Do I need to defrost the refrigerator before rehanging?

Required if:

• Model with No Frost —frost in the freezer can interfere with dismantling.
• The refrigerator has not been turned off for more than 6 months—accumulated ice makes the door heavier.

For defrosting, 4–6 hours at room temperature are enough. Do not use a hairdryer or hot water - this will damage the seal.

What to do if, after rehanging, the door does not close tightly?

Causes and solutions:

• Distortion loops → Adjust them with a hexagon.
• Deformed seal → Warm it up with a hairdryer (max. 50°C) and lubricate it with silicone.
• Interfering shelves → Check whether they cling to the body when closing.

If the problem remains, the magnetic tape in the seal may have been damaged during installation. It can be replaced separately (the article depends on the model).

Is it possible to reverse the door on an LG Side-by-Side refrigerator?

Technically yes, but this is extremely difficult due to:

• Large weight of doors (from 20 kg each).
• Complex hinge system (often a special key is required).
• Risk of damage to electronic modules (in models with Smart ThinQ).

The cost of work in the service is from 4,000 rubles. It is not recommended to undertake this on your own.