How to rehang the doors of an Atlant refrigerator: instructions with photos and nuances

Re-hanging the refrigerator door Atlant is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Unlike models of other brands, refrigerators from the Belarusian manufacturer have their own design features that are important to consider. For example, most modern Atlant provides the ability to rehang without dismantling the hinges - just rearrange the fasteners and reconfigure the magnetic seals.

In this article you will find step-by-step instructions with photosa list of necessary tools and typical mistakesthat beginners can use. We will analyze the process for different models - from classic single-chamber to dual-chamber systems No Frost. You will also learn how to properly adjust the door after rehanging to avoid distortions and loss of cold.

Before you begin, check: if your refrigerator is under warranty, independent intervention may void it. Check this point with the service center Atlant.

Preparation: tools and conditions

For work you will need:

• ⚒️ Phillips screwdriver (usually PH2 or PH3) - for hinge screws and fastenings.
• 🔧 Hex wrench (if the model uses internal hex bolts).
• 📏 Tape measure or ruler - to check the gaps after rehanging.
• 🧲 Magnet (optional) - will help hold small parts during dismantling.
• 🧴 Silicone grease - for processing hinges after installation.

Also prepare the work space:

• 🚪 Clear access to the refrigerator from all sides (at least 1 m of space).
• 🔌 Turn off the power and defrost the refrigerator (if required).
• 📦 Remove all products and shelves from the door - they will get in the way.

Single-chamber|Double-chamber with freezer on the bottom|Double-chamber with freezer on top|Side-by-Side|I don’t know the model-->

Important! In models Atlant electronically controlled (for example, series XM or NM) after rehanging, a reset may be required. Usually, to do this, it is enough to disconnect the refrigerator from the network for 10–15 minutes.

⚠️ Attention: If your refrigerator is equipped with water dispenser (for example, Atlant MXM 2835-90), re-hanging the doors will require additional reconfiguration of the water supply pipes. Without experience, it is better to contact the service.

Step 1: Removing the door - step by step with photo

Let's start with the top hinge (if there is one door) or with the hinges of the refrigerator compartment (if the model is two-chamber). Algorithm of actions:

1. Remove decorative plugs from the hinges. They are usually secured with latches - pry them off with a flat-head screwdriver or knife. In some models, the plugs are screwed on.

2. Unscrew mounting screws the top hinge. Models Atlant often use Phillips or hex screws. Do not lose washers and gaskets - they may vary in thickness for different sides!

3. Hold the door and carefully remove it from the bottom loops. If the door is heavy (for example, in models with No Frost), ask an assistant.

4. Remove the door to a safe place, placing it on a soft surface (towel, cardboard) so as not to scratch it.

For two-chamber refrigerators, the process is similar, but first remove the refrigerator door chamber, then the freezer. In models with French door (for example, Atlant XM 6026-080), the dismantling procedure may differ - see the instructions for the specific model.

Is the power turned off?|Have all products and shelves been removed?|Has the place for installation been prepared? doors?|Is there a helper for heavy doors?-->

Nuance: In refrigerators Atlant older than 2010, the hinges can be fixed not only with screws, but also with rivets. In this case, you will need a drill to drill them (drill diameter - 3–4 mm).

Step 2: Transferring the hinges to the other side

After dismantling the door, you need to move attaching hinges to the opposite side. There are several key points here:

• 🔄 On the refrigerator body and door there are usually factory holes for attaching hinges on the other side. They are closed with plugs - remove them.
• 📏 Check symmetry of the holes. In some models (for example Atlant MXM 2833), the holes for the hinges on different sides may have different diameters.
• 🔧 Transfer the hinges to the new side, using the same screws and washers. Do not tighten them completely - leave some play for adjustment.

If there are no holes for the hinges on the other side (true for older models), you will have to drill them yourself. To do this:

1. Measure the distance from the edge of the case to the center of the holes on the current side.
2. Transfer the markings to the opposite side, using a level for accuracy.
3. Drill the holes with a metal drill (diameter - 0.5 mm less than the diameter of the screws).

⚠️ Attention: When drilling, do not hit the refrigerant pipess that run along the back wall of the case. They are usually located closer to the center, but in some models they can approach the side walls.

Step 3: Rearranging the handle and magnetic seal

The door handle Atlant is attached to screws hidden under the decorative trim. To remove it:

1. Pry the trim from the side with a flat screwdriver or knife.
2. Unscrew the screws (usually 2-3 pieces) and remove the handle.
3. Move the handle to the other side using the existing holes.

With magnetic seal (rubber band) the situation is more complicated. In most models Atlant it is symmetrical, but sometimes it requires adjustment:

• 🔍 Check whether there is a seal on the seal marking “Top” or “Bottom”. If yes, do not turn it over.
• 🌡️ After reversing, the seal may become deformed. Warm it up with a hairdryer (temperature 50–60°C) and give the desired shape.
• 🧴 Lubricate the seal with silicone greaseso that it does not harden over time.

In models with No Frost (for example, Atlant XM 6026-080) the seal may have Additional magnetic inserts. When rehanging, make sure that they have not moved - otherwise the door will not close tightly.

Step 4: Installing the door on the new side

Now you can return the door to its place. Do this in reverse order:

1. Place the door onto bottom hingeholding it by the top edge.
2. Align the top hinge with the holes and insert the screws (not tighten!).
3. Check that the door hangs smoothly, without distortions.
4. Tighten all the screws, starting with the top hinge.

For two-chamber refrigerators, install the freezer door first, then the refrigerator door. In models with French door the order may differ.

Problem: If the door is after installation opens spontaneously, this means that the refrigerator is not level. Adjust the height of the legs or use a level to check.

Step 5: Adjusting the hinges and checking the tightness

Even if the door hangs level, it necessary adjust for a tight fit. In models Atlant this is done like this:

• 🔧 Loosen the screws on the hinges (do not unscrew completely!).
• 📏 Adjust the door position vertically and horizontally, checking gaps.
• 🔨 Tighten the screws starting from the top hinge.

To check the tightness, use test with a sheet of paper:

1. Insert a sheet of paper between the seal and the body.
2. Close the door and try to pull out the sheet.
3. If the sheet comes out easily, the seal needs to be adjusted or replaced.

In refrigerators with No Frost poor tightness leads to icing of the evaporator and increased load on the compressor If after adjustment the problem remains, check the seal for cracks.

⚠️ Attention: In models Atlant s display on the door (for example, Atlant MXM 2835-90) After re-hanging, it may be necessary to reconfigure the sensors. If the display does not work, contact the service.

Typical errors and how to avoid them

Even with careful work, you can make mistakes that will lead to loose closure, creaking hinges or damage to the seal. Let's look at the most common ones:

• 🔨 Overtightened hinge screws —this leads to door deformation and difficult opening. Tighten the screws with force, but without fanaticism.
• 🔄 Mismatched holes —if you drilled new holes not according to the markings, the hinges may dangle. Use a cardboard template for accuracy.
• 🧲 Damaged seal —if the elastic is torn or lost its shape, it needs to be replaced. A temporary solution is heating with a hairdryer.
• ⚖️ Uneven floor —if the refrigerator is on a slope, the door will open on its own. Use a level and adjust the legs.

Another common problem is creaking hinges after re-hanging. To fix it:

1. Remove the decorative plugs from the hinges.
2. Apply silicone lubricant to the hinge axis.
3. Open/close the door several times to distribute the lubricant.

What to do if the door does not close after rehanging?

If the door does not close tightly, check

1. Correct installation of the seal (is it twisted?).

2. Gaps around the perimeter (must be the same).

3. The position of the hinges - they may need to be shifted by 1-2 mm.

If the problem remains, most likely the door body has become deformed. In this case, only replacement will help.

FAQ: Frequently asked questions about re-hanging doors Atlant

Is it possible to re-hang the refrigerator door Atlant on your own if it is under warranty?

Technically yes, but this voids the warranty to the refrigerator. If you need to rehang the door during the warranty period, contact the official service center Atlant. They will do it for free or for a nominal fee.

How long does reweighing take?

On average, the process takes 1-2 hoursif you have experience with tools. For a beginner, it may take up to 3-4 hours, especially if you have to drill new holes.

Do you need to defrost the refrigerator before rehanging?

Absolutely! Disconnect the refrigerator from the mains and wait until it is completely defrosted. This will prevent the formation of condensation on electronic components and make it easier to access the hinges.

What should you do if, after rehanging, the refrigerator begins to operate loudly?

This may be due to:

• 🔊 Not closing the door tightly —check seal.
• ⚙️ By moving the compressor —if the refrigerator was moved, it could move. Check its position.
• ❄️ By icing the evaporator —if the model is with No Frost, defrost the refrigerator completely.

Is it possible to hang the door by model Atlant 2005?

Yes, but in older models they are often used rivets instead of screws, so you will need a drill to drill them out. There may also be no factory holes for hinges on the other side - you will have to make them yourself.

If you are not confident in your skills, it is better to contact a specialist - old refrigerators are more fragile.