How to properly hang the doors of an LG refrigerator: step-by-step instructions with photos and tips

Rehanging doors refrigerator LG is a task that many owners face when moving, renovating a kitchen, or simply wanting to change the opening side. It would seem that what is so difficult here? But in practice, incorrect actions can lead to misaligned hingesdamage to the rubber seal or even breakage of the plastic fasteners. This is especially true for models with a system No Frost and electronic control, where the door is connected to sensors and wires.

In this article we will figure out how to rehang doors on your ownwithout resorting to the services of a specialist. You will learn what tools you will need, how to avoid common mistakes (for example misalignment of the upper and lower hinges after reweighing), and what to do if the door does not close well after the procedure. And also some nuances for popular series LGsuch as GA-B489, GR-N309 or InstaView Door-in-Door.

Preparation for reweighing: tools and measures safety

Before you start work, make sure you have everything you need. Most models LG are equipped with a special key for hinges (usually it comes in the box with documents), but if you don’t have it, 5 mm hexagon or a Phillips screwdriver will do. Here is a complete list of tools:

• 🔧 Hex wrench (5–6 mm) or screwdriver with bit
• 🔨 Flat screwdriver (for removing decorative plugs)
• 📏 Level (to check the evenness of the door after installation)
• 🧲 Magnet or tape (to temporarily fix the door)
• 🧴 Silicone grease (for hinges after hanging)

Important: before starting work unplug the refrigerator and empty the doors of food. If the model has a water dispenser (LG InstaView), close the water supply tap and drain the remaining liquid from the system. Do not ignore this step - if the door is skewed, the hose may be damaged and water will flow onto the floor.

Step 1: Removing the top door (freezer)

On most models LG the process begins with the top door. Here are step-by-step instructions:

1. Open the freezer door 90 degrees and lock it (you can place a book or ask an assistant).
2. Remove the decorative plugs from the hinges - they are attached to latches. Pry them off with a flat-head screwdriver, starting from the bottom edge.
3. Unscrew the top hinge bolts (usually 2-3 pieces). In models LG GA-B489 and similar ones, the bolts can be hidden under a plastic cover - it must be carefully moved up.
4. Holding the door, remove it from the hinge pin and place it on a soft surface (for example, on a blanket).

⚠️ Attention: Do not pull the door towards you - it is heavier than it seems! In freezers with a system No Frost there are wires running inside the door to the sensors. If you pull sharply, you can tear off the connector.

Make sure that the refrigerator is unplugged from the outlet|

Take a photo of the location of the hinges and plugs|

Prepare a place for careful installation doors|

Check the presence of an assistant (doors weigh 10–15 kg)-->

Step 2: Removing the middle hinge (for two-chamber models)

If you have a two-chamber refrigerator (for example, LG GR-N309), between the freezer and main door there intermediate hinge. It must be removed to free the lower door. Proceed as follows:

1. Unscrew the bolts securing the middle hinge to the refrigerator body (usually 2 bolts from the bottom and 1 from the top).
2. Carefully remove the hinge - it can be connected to the lower door bracket.
3. If the loop is “sour” and cannot be removed, do not use force. Treat the bolt threads WD-40 and wait 10 minutes.

In some models (for example, LG Door-in-Door), the middle hinge is connected to a mechanism EasyOpen —a soft opening system. When dismantling, do not lose the small spring inside the hinge!

What to do if the hinge bolt does not unscrew?

If the bolt is “stuck” or the thread is broken:

1. Try to unscrew it counterclockwise with force, but without jerking.

2. If it doesn’t help, use a socket wrench instead of a screwdriver for better grip.

3. As a last resort, cut the bolt with a hacksaw for metal, but then you will need to replace the hinge (the article can be found in the instructions for the model).

Step 3: Hanging the bottom door (refrigerator compartment)

The bottom door is removed in the same way as the top one, but there are some nuances here:

• 🔹 In models with a dispenser (LG InstaView) before removing the door, disconnect the water supply hose. It is attached with a plastic clamp - press it and pull the hose down.
• 🔹 If the door “sticks” to the body, pry it with a flat screwdriver in the place of the seal (but do not damage the rubber!).
• 🔹 After removal, check magnetic seal — if it is deformed, after rehanging the door will not close well.

⚠️ Attention: In refrigerators with an electronic display (for example, LG ThinQthere are wires running inside the door to the control panel. When re-hanging, they must not be bent or pulled - this may damage the control module!

Step 4: Transferring the loops to the other side

Now you need to move the loops to the opposite side. It is important to maintain symmetry here:

1. Remove the plugs on the other side of the refrigerator (where the hinges will be attached). They are usually held on by clips.
2. Move the loops to the new holes. In most models LG there are already holes - they are closed with plastic plugs.
3. Tighten the bolts, but not all the way. First you need align the door level.

For models with Door-in-Door (door in door), the process is more complicated:

• 🔹 First, the main door is re-hung.
• 🔹 Then - internal door (it is mounted on separate hinges).
• 🔹 Check that the gap between the doors is the same around the entire perimeter.

Step 5: Installing the doors and adjusting

The most important step is to hang the doors back and adjust their position. Proceed as follows:

1. Place the top door on the hinge pin and lightly tighten the bolts.
2. Install the middle hinge (for two-chamber models) and fix it.
3. Hang the bottom door. She must close smoothly effortlessly.
4. Tighten all bolts, but do not overdo it - you can break the threads.

After installation, check:

• 🔹 Doors open at 90° and do not return back (if this is not a function AutoClose).
• 🔹 The seal fits evenly around the entire perimeter (you can check it with a sheet of paper - it should hold tightly).
• 🔹 There are no distortions - use a level or visually assess the gaps.

⚠️ Attention: If after rehanging the refrigerator became louder work, check whether the door touches the internal pipes or the fan (in models with No Frost). This may lead to breakage of the compressor!

Typical mistakes and how to avoid them

Even if you carefully follow the instructions, you can make mistakes that will lead to problems:

• 🚫 Mismatch of holes - if the hinges do not move to a new place, do not try to “drive them in”. mixed up the upper and lower hinges (they are often asymmetrical).
• 🚫 Walk of the door - if after installation the door “falls” to the side, loosen the bolts and adjust the position of the hinge.
• 🚫 Damage to the seal - if there is an elastic band is torn or deformed, it needs to be replaced. Article numbers of seals for LG can be found according to the refrigerator model.
• 🚫 Forgot to rearrange the magnetic holders - in some models they are attached to the door and you need to move them to the other side.

What to do if the door does not close after rehanging?

1. Check if anything is in the way inside the refrigerator (shelves, drawers).

2 Adjust the height of the hinges - sometimes it is enough to tighten the bolts by 1-2. mm.

3. If the problem is in the seal, heat it with a hairdryer (temperature 50–60°C) and shape it with your hands.

4. As a last resort, call a specialist to diagnose the hinges.

If you have re-hung the doors, but the refrigerator has become less freezing, check:

• 🔹 Whether the temperature sensor has moved (in models with electronic control).
• 🔹 Are the wires going to the display or system damaged? No Frost.
• 🔹 Have any cracks appeared in the seal - even 1-2 mm is enough for loss cold.

FAQ: Frequently asked questions about re-hanging LG doors

Is it possible to re-hang the doors of an LG refrigerator yourself if you have no experience?

Yes, but only if you are confident in your abilities and carefully follow the instructions. Start with simple models without electronic panels (for example, LG GA-B489). For refrigerators with dispenser or system ThinQ it is better to invite a specialist - there is a risk of damaging the electronics.

How long does re-hanging take?

On average - 1-2 hours, if there are no complications, the most time is spent on adjusting the doors after installation. c Door-in-Door the process can take up to 3 hours.

Is it necessary to top up the freon after re-hanging?

No, re-hanging the doors does not affect the tightness of the freon circuit. Refilling is only required if the tubes are damaged (for example, if you accidentally drilled. body).

What to do if, after re-hanging, the refrigerator starts to operate loudly?

Most likely, the door is touching internal parts (fan or pipes). Open the door and check for any extraneous vibrations when the compressor is operating. If the noise does not disappear, call a technician for diagnostics.

Is it possible to re-hang the doors? on an LG refrigerator with the InstaView system?

Yes, but this is more complicated due to the additional wires to the dispenser and sensors. You will need to carefully disconnect the connectors and move them to the other side. If you are not sure, it is better to contact a service center. LG.