Moving or purchasing new equipment often poses owners with a difficult question: how to safely deliver bulky equipment to its destination? Liebherr refrigerators They are famous for their reliability and complex internal design, therefore they require a special approach when moving. Improper transportation can lead to damage to the compressor, failure of the tightness of the circuit or deformation of the case, which will make further operation impossible.
There are many myths that modern equipment can be transported in any position, but manufacturers categorically do not recommend relying on luck. Liebherr is a premium brand that uses advanced cooling technologies that are sensitive to shaking and changes in the position of the tubes. In this article we will analyze all the nuances of preparation, packaging and the actual loading process so that your unit arrives intact.
Ignoring simple logistics rules often results in expensive repairs or complete replacement of the compressor. Transportation should be planned in advance, taking into account the door dimensions openings and weight of the device. Let's take a detailed look at how to minimize risks and ensure the safety of all components when moving.
Preparing the refrigerator for moving
You need to start preparing long before the movers arrive. The first and most important step is to completely defrost the chambers. Even if your model is equipped with a system NoFrostthere may be particles of ice or condensation inside, which, when tilted, will flow onto the electronic circuit boards or into the thermal insulation layer.
Disconnect the device from the power supply at least 24 hours before the planned transportation. This time is necessary for the refrigerant and oil in the compressor to be redistributed, and for all the ice to melt. Moisture is the main enemy of electronics, so thoroughly wipe all internal surfaces with a dry rag.
⚠️ Attention: Do not use a hair dryer or other heating devices to speed up defrosting. A sharp change in temperature can damage plastic elements and seals.
After removing moisture, remove all removable elements: shelves, drawers, egg trays and bottle holders. They must be packaged separately, lined with paper or bubble wrap. The doors must be secured so that they do not swing open en route and damage the hinges or adjacent objects.
☑️ Preparation for transportation
Vertical or horizontal transportation
One of the most common questions concerns the position of the unit during transportation The ideal option for any equipment, including Liebherr, is a strictly vertical position. In this case, the oil remains in the compressor crankcase, and the tubes do not experience critical fracture loads.
However, the realities of moving often dictate their own conditions, and transportation in a lying position becomes inevitable. If you decide to carry the refrigerator lying down, remember: being in a horizontal position should not exceed 15-20 minutes. Longer - the risk of oil getting into the refrigerant circulation circuit increases many times over.
There is a misconception that modern compressors are equipped with systems that prevent oil leakage. In practice, this does not always work, especially when shaking on uneven roads. Horizontal transportation Only permissible for short distances and subject to strict packing rules.
If you transport equipment in the back of a truck, be sure to secure it with straps. Even slight vibration during movement can dislodge loose cargo, causing impacts against the sides. Make sure that the substrate under the refrigerator is smooth and clean.
Rules for packaging and protecting the case
The case of refrigerators Liebherr is often made of stainless steel or high-quality plastic, which are easily scratched. For protection, use the original cardboard box if it still exists. This is the best option, since the dimensions perfectly match the dimensions of the device.
If the original packaging is not available, use thick cardboard, stretch film and bubble wrap. Pay special attention to the corners and handles - these are the most vulnerable places when loading. Wrap the body with several layers of film to protect the coating from dust and minor abrasions.
Use masking tape or special belts to secure the doors. Ordinary office tape can leave sticky marks or damage the coating when removed. Fixation It should be reliable, but not too tight, so as not to deform the sealing rubber.
Features of transporting Side-by-Side models
Type models Side-by-Side have impressive dimensions and weight, which creates additional difficulties. Often they cannot be carried into the doorway assembled, so the doors may need to be dismantled. The instructions for a specific model Liebherr always have a section on removing door panels.
When dismantling, be sure to mark the hinges and doors so that when reassembling in a new place you do not confuse the left and right sides. Removed doors must be transported separately, tightly pressed to the wall or floor, excluding their bending.
The weight of such models can reach 150 kg or more, so moving requires at least two strong people or the use of a special trolley with belts. Trying to transport Side-by-Side alone is almost guaranteed to result in a back injury or falling equipment.
| Model type | Recommended position | Max. travel time lying down | Nuances |
|---|---|---|---|
| Single-chamber | Vertical | up to 15 minutes | Easier than multi-chamber |
| Double-chamber | Vertical | up to 10 min | Risk of compressor displacement |
| Side-by-Side | Strictly vertical | Not recommended | Door dismantling required |
| Built-in | Vertical | up to 10 minutes | Remove facade panel |
Adaptation after transportation
After the refrigerator has been delivered and installed in a new location, you cannot immediately plug it into the network. If transportation took place in a horizontal position, compressor oil could get into the evaporator tubes. It takes time for it to drain back into the crankcase.
The settling time depends on the season and the position during transportation. In summer, 2-4 hours are enough, in winter - at least 6-8 hours, especially if the equipment was brought in from frost. Condensationformed inside must be completely dry before applying voltage.
⚠️ Attention: Turning on a wet or not settled refrigerator may lead to a short circuit or water hammer in the compressor, which is not a warranty case.
It is better to make the first start without loading products. Let the unit run idle for 1-2 hours until it reaches operating temperature. Only after this can the chambers be gradually filled.
What to do if the refrigerator does not freeze after transportation?
If, after observing all the time intervals, the equipment does not cool, it is possible that the oil has clogged the capillary tube or a refrigerant leak has occurred. In this case, you need to call a technician to purge the system or refill with freon.
Typical errors during transportation
The most common mistake is neglecting to secure the internal elements. Even if you've removed the shelves, a forgotten vegetable tray can dangle and break the glass partition the first time you turn the car.
Another mistake is using upholstered furniture or blankets instead of hard packaging. Blankets dampen only minor vibrations, but do not protect against pinpoint impacts or squeezing. Liebherr is technical and needs rigid body protection.
Often owners forget to check the condition of the wheels or support legs before loading. If the legs are damaged or lost, the refrigerator will stand unsteadily, which will lead to increased noise and vibration during operation.
Is it possible to transport a Liebherr refrigerator at sub-zero temperatures?
Short-term transportation at sub-zero temperatures is permissible, but before turning on the equipment must be kept in a warm room for at least 24 hours. This is necessary to warm up the compressor oil and evaporate condensation from the electrical contacts.
Is it necessary to remove the doors of a regular two-chamber refrigerator?
Usually this is not required if the width of the doorways allows the body to be carried through. Removing the doors increases the risk of damage to the hinges and disruption of the geometry of the canvas, which will affect the fit of the seal.
What to do with the remaining water in the NoFrost system?
In the NoFrost system, water from the drainage may remain in hard-to-reach places. After defrosting and wiping, it is recommended to leave the refrigerator with the doors open for several hours in a ventilated area to dry completely.
Is shaking dangerous for the compressor?
Yes, strong shaking can lead to broken tubes inside the compressor or displacement of the motor suspension springs. Therefore, when loading into a car, avoid throwing and hitting, and try to choose smooth roads on the way.