After purchasing a new household appliance, the owner is faced with the task of not only delivering the unit home, but also installing it correctly. Errors at the stage of unpacking or initial startup can lead to serious damage to the compressor or violation of the housing geometry. Correct connection is the key to long and silent operation of your Atlanta for many years.
Many users look for video materials to visually verify the correctness of their actions, since text manuals are not always clear. In this article we will analyze in detail each stage, from removing the transport packaging to setting the temperature conditions, based on the official recommendations of the manufacturer.
It is worth noting that modern models may have differences in design, but the basic principles remain unchanged. Compliance with technology installation will allow you to avoid most of the problems that inexperienced users encounter when starting up for the first time.
Transportation and unpacking of equipment
The first critical step is the correct movement of the unit. If the refrigerator was delivered in a lying position, it must be allowed to stand upright. This time is necessary for the oil to flow into the compressor, otherwise water hammer may occur water hammer.
Remove all external packaging materials, including cardboard, tape and foam pads. Pay special attention to the internal space: remove all shelves, drawers and trays that may be secured with tape to prevent damage during transportation.
⚠️ Attention: Do not use sharp objects (knives, screwdrivers) to remove the factory tape from the case, so as not to damage the paintwork or decorative elements.
Transport bolts, if present on your model, they usually secure the compressor or other moving parts. They must be unscrewed and saved, since during repeated transportation their installation is mandatory for the safety of the equipment.
Check the integrity of the door seals. They should be clean, elastic and fit snugly around the entire perimeter of the body. Any creases can lead to loss of tightness in the future.
Choice of installation location and room requirements
For stable operation, the refrigerator requires the right place. It should be protected from direct sunlight and located away from heating devices such as radiators or gas stoves. Thermal radiation causes the compressor to work harder, increasing energy consumption.
The distance to walls and furniture should ensure free circulation of air. The rear grille of the condenser must have a gap of at least 5-7 cm from the wall. Side clearances are also important for models where heat dissipation occurs through the side walls.
The floor surface must be flat and hard. If the floor has unevenness, it is necessary to compensate for it with adjustable supports. Installation on a soft carpet is not recommended, as this impedes the heat transfer of the lower part of the case.
Do not place the unit in rooms with temperatures below +10°C or above +32°C, unless otherwise specified in the passport of a specific model. Atlant. Extreme temperatures can disrupt the operation of the thermostat and the refrigerant system.
Alignment of the case by level
The correct operation of the doors and the self-closing system directly depends on the horizontal position of the refrigerator. To check, use a building level, placing it on the top panel or shelves.
Rotate the front adjustable supports to achieve a stable position. It is often recommended to slightly tilt the body back (about 2 degrees) so that the doors open freely and slam themselves when not completely closed.
☑️ Checking the installation
If the refrigerator does not stand level, this can lead to skewed door hinges and a violation of the tightness of the circuit. In the long term, this causes ice freezing and increased wear of the seal.
Electrical connection and grounding
Refrigerators Atlant usually equipped with a cord with a Euro plug that has a grounding contact. It is extremely important that the outlet to which you connect the equipment also has a reliable ground. This ensures safe operation and protection from electric shock.
It is not recommended to use extension cords or tees, especially if they are of poor quality. Direct connection to a fixed outlet is the safest option. The outlet should be easily accessible so that, if necessary, you can quickly turn off the device.
⚠️ Attention: It is forbidden to connect the refrigerator to the network if the voltage in your electrical network is unstable. Voltage surges can damage the electronic control module.
If voltage surges frequently occur in your home, it is advisable to purchase a stabilizer or surge protector with a protection function. This will extend the life of compressor and electronics.
Make sure that the wire is not pinched by furniture or is not located in a high temperature area. Damage to the insulation of the power cord is unacceptable and requires immediate replacement of the cable by an authorized service.
First start-up and temperature setting
After the refrigerator has stood in an upright position (at least 2-4 hours if it was transported lying down), you can turn it on. When you turn it on for the first time, do not load food right away.
Let the unit run idle for 2-3 hours. During this time, the chambers should cool down to the set temperatures, and the automatic shutdown system should work. This will check the tightness and efficiency of the refrigeration circuit.
Why can’t you load food right away?
If you load warm food into a refrigerator that has not cooled down, the compressor will work hard, trying to cool a large volume. This can lead to overheating and breakdown in the first hours of operation.
Adjust the thermostat. In mechanical models, this is a rotary knob with numbers from 1 to 7 (where 7 is the coldest setting). In electronic models, the temperature is set exactly in degrees through the control panel.
For initial start-up, set the average value. After the products are completely frozen and loaded, you can fine-tune depending on your needs and how full the chambers are.
Table of recommended temperature conditions
Correct setting of the temperature regime is the key to maintaining the freshness of products. Different areas of the refrigerator are designed for different types of storage. Below is a table of optimal values for standard operation.
| Storage area | Recommended temperature | What to store | Thermostat position |
|---|---|---|---|
| Main chamber | +2...+4 °C | Ready meals, dairy products, sausages | Average (3-4) |
| Zero zone (Fresh) | 0...+1 °C | Raw meat, fish, vegetables for a short period of time | Minimum (1-2) |
| Freezer compartment | -18 °C and below | Frozen semi-finished products, meat, berries | Maximum (6-7) |
| Door shelves | +5...+8 °C | Drinks, sauces, eggs, butter | Depends on the main |
Please note that the temperature at different points in the chamber may vary. The top shelves are usually warmer, while those above the vegetable drawers are cooler due to air circulation. Place food with this in mind.
Do not place hot or warm food inside. This sharply increases humidity and temperature, forcing the compressor to work in emergency mode. Cool the food to room temperature before storing it.
Checking operation and eliminating noise
In the first hours of operation, you can hear various sounds: gurgling of refrigerant, clicking of the thermostat, humming of the compressor. These are normal operating sounds of the system Atlant.
However, if you hear a strong knocking, grinding or vibration of the housing, you need to stop the unit and check the installation. Vibration is often transmitted to the floor or furniture if the supports are not adjusted.
Check whether the condenser pipes from behind are touching the cabinet wall or other objects. The gap must be free. Also make sure that bottles or cans inside the chamber do not touch each other, creating rattling.
⚠️ Attention: If the noise is accompanied by a burning smell or smoke, immediately unplug the refrigerator and contact a service center. Operation in this condition is prohibited.
Frequently asked questions when connecting (FAQ)
How long should the Atlant refrigerator sit after transportation?
If the refrigerator was transported in a vertical position, 30-60 minutes is enough. If in horizontal mode - at least 2-4 hours, but it is better to leave it overnight. This is necessary for the oil to drain into the compressor.
Why do the side walls of the refrigerator get very hot?
In modern models Atlant capacitors (heat exchangers) are often built into the side walls. Their heating to 40-50 degrees in the first hours of operation or during active freezing is a normal physical process of heat removal.
Is it possible to turn on the refrigerator immediately after defrosting?
Yes, if you have just washed or defrosted it, you can turn it on immediately. But if it was transported, the settling rules apply. It is better to load products after reaching temperature.
What to do if the door does not fit tightly?
Check if anything is interfering with the seal (packaging, crumbs). Make sure the refrigerator is level. If the seal is deformed, you can try to straighten it with a hairdryer (carefully!) or replace it.
Do you need to defrost the No Frost chamber separately?
The system No Frost assumes automatic defrosting of the evaporator. However, it is recommended to completely defrost and wash the refrigerator at least once a year for hygiene and removal of odors.