Buying new household appliances is always a joyful event, but it is accompanied by the need for proper installation. Beko refrigerator has established itself as a reliable and functional unit, but its durability directly depends on how well the installation is done. Incorrect transportation or hasty connection to the network can cause the failure of an expensive compressor.
The connection process does not require special engineering knowledge, but requires strict adherence to the sequence of actions. Modern models The Turkish brand is equipped with complex electronics that are sensitive to voltage drops and vibrations. That is why it is important not just to plug the cord into a socket, but to prepare the device for the first start-up.
In this material we will analyze in detail all the stages: from unpacking to checking temperature conditions. You will learn why you cannot turn on the device immediately after bringing it into the apartment and how to ensure ideal operation of the system No Frost. Following these simple rules will help you avoid calls to the service center in the future.
Unpacking and initial inspection of the equipment
The first step after delivery is careful unpacking. Box paper and protective tapes must be completely removed. Pay special attention to the internal space: all shelves, drawers and trays are often secured with tape or foam inserts to prevent damage during transportation. Glass of shelves Must be intact, without chips or cracks.
After removing all removable elements, conduct a visual inspection of the case. There should be no dents or deep scratches on the enamel, especially in the area of doorways and seals. If you notice damage, it is better to document it with the seller before signing the acceptance documents.
⚠️ Attention: Do not throw away the packaging materials immediately. If it is necessary to return or transport to a service center, the presence of the original box and foam is a prerequisite.
It is important to check the package contents. The instructions for the models Beko indicate the presence of all necessary accessories, such as egg trays, bottle racks and fasteners. Make sure that the kit includes a product passport with a completed warranty card.
Choice of installation location and ventilation requirements
Correct location of the unit - the key to its effective operation. Refrigeration equipment during operation, it generates heat, which must be freely removed from the back wall and side panels. If you place the device close to a wall or furniture, the compressor will work with overload, trying to maintain the set temperature.
Instructions Beko recommends leaving gaps for air circulation. The minimum distance from the back wall to the wall of the room should be at least 5-7 cm. It is also necessary to leave space at the top, especially if you plan to build a refrigerator into a kitchen unit or install a microwave oven on it.
It is not recommended to install equipment near heating appliances, gas stoves or in direct sunlight. An increased external temperature will force thermostat to work in increased mode, which will lead to increased energy consumption and wear of parts.
Aligning the body and adjusting the supports
The stable position of the refrigerator is critical for quiet operation and proper closing of the doors. If the case is skewed, the door may open spontaneously or, conversely, not fit tightly, breaking the seal of the chamber. Cooling system It is also sensitive to distortions, which can cause problems with condensate drainage.
For adjustment, front supports are used, which are usually rotating legs. By rotating them clockwise or counterclockwise, you can change the height of the corner. The rear legs, as a rule, are not adjustable, so the alignment is carried out precisely by the front elements.
☑️ Checking the installation
The correct position is when the front of the refrigerator is slightly raised relative to the back. This ensures that the door closes naturally under the influence of gravity if it is opened no more than 45 degrees. You can check the horizontal position using a building level placed on the top cover.
Adaptation time before first use
One of the most important points that is often forgotten is the acclimatization time. If the refrigerator was delivered during the cold season, condensation formed inside the electronics and compressor should completely evaporate. Turning on a wet device can lead to a short circuit.
In addition, there is refrigeration oilin the compressor. If it was shaken during transportation, it could get into the refrigerant circuit. It takes time for the oil to return to the compressor crankcase and stabilize the pressure in the system. For models Beko with an inverter compressor, this is especially true.
What happens if you turn on the refrigerator right away?
If you turn on the device immediately after winter delivery, the compressor may burn out due to water hammer or jamming. Temperature sensors may also display incorrectly.
The recommended holding time depends on transportation conditions. In summer, 2-3 hours is enough. If the equipment was brought in from the cold, experts advise waiting 4 to 8 hours before connecting the power cable to the network.
Electrical network connection diagram
Connection to the electrical network should be made into a separate grounded outlet. The use of extension cords, tees and adapters is undesirable, as they can cause poor contact and heating of the wiring. Current strength The circuit must meet the requirements specified on the technical sticker inside the camera.
Make sure that the voltage in the network is stable. Voltage surges can damage the electronic control module, which is the “brain” of a modern refrigerator. If there are frequent power outages in your area, it is recommended to use a voltage stabilizer.
| Parameter | Recommended value | Tolerable deviation |
|---|---|---|
| Voltage | 220-230 V | ± 10% |
| Frequency | 50 Hz | ± 1 Hz |
| Type sockets | With grounding | Eurostandard |
| Separate line | Preferably | Not through an extension cord |
Power cord should not be pulled or pinched by the furniture body. Check the integrity of the cable insulation. If damage is detected, it is prohibited to operate the device until the cord is replaced by an authorized service.
First launch and setting modes
After the refrigerator has been standing and connected to the network, you need to start it idle. Loading the cameras with products right away is a mistake. Empty chambers are easier to reach the desired temperature, and the compressor will turn off, showing the normal operating cycle.
On the control panel or using the mechanical regulator, set the average temperature value. For the main compartment this is usually +4°C, for the freezer - -18°C. You should not immediately turn the regulator to maximum, this will create an extra load.
⚠️ Attention: During the first hours of operation, the refrigerator may make gurgling sounds or a slight hum. This is a normal process of circulation of refrigerant through the system and operation of the compressor.
Let the equipment run idle for 2-4 hours. During this time, check how well the shelves are cooling and make sure that the doors fit tightly around the entire perimeter. Only after the temperature has stabilized can you begin to gradually load products.
Diagnosis of common startup problems
Sometimes, after connecting, users encounter situations that seem to be malfunctions, but are not. For example, strong heating of the side walls. In modern models Beko capacitors (heat exchangers) are often built into the side panels, so heating up to 50-60°C in the area of contact with them is the normal mode of heat removal.
If the refrigerator does not turn on or constantly works, do not rush to call a technician. Check that the doors are tightly closed and that there is nothing obstructing the seal. Also make sure that the temperature mode is set correctly for the current load.
If an error appears on the display or incorrect operation, refer to the code table in the instructions. Often the problem is solved by simply rebooting the device by disconnecting from the network for 15 minutes.
Why does the Beko refrigerator hum after installation?
The hum may be caused by improper installation. Check that the cabinet is not touching furniture or walls. Also make sure that all shipping bolts (if there were any on the compressor) have been removed, although newer models usually do not have them. If the humming is accompanied by vibration, adjust the legs.
How long does it take the refrigerator to reach temperature?
Primary cooling of empty chambers to the specified parameters takes from 2 to 6 hours, depending on the model, ambient temperature in the room and the volume of the chambers. Full stabilization after loading with food occurs within 24 hours.
Is it possible to install a Beko refrigerator in an unheated country house?
Most models are designed for use in the SN-T climate class (from +10°C to +43°C). Operation at temperatures below +10°C can lead to solidification of the oil in the compressor and disruption of the thermostat, which will disable the equipment.
What to do if the door does not hold?
Check the housing tilt adjustment - the front part should be slightly higher than the back. If this does not help, inspect the seal for dirt or deformation. In new models, the seal can be hard and takes time (2-3 days) to fully expand.