Reversing the LG refrigerator door to the other side: instructions with photos and tips

Reversing the refrigerator door LG to the opposite side is a task that owners face when moving, renovating a kitchen, or simply wanting to optimize space. Unlike Soviet models, where the door was attached to two hinges, modern refrigerators (especially those with a system No Frost or built-in display) require accuracy and knowledge of the nuances. For example, in models LG DoorCooling+ or InstaView the process is complicated by the presence of electronic components and additional fasteners.

In this article you will find step-by-step instructions with photosan analysis of typical errors (for example, why a door can sag after hanging), as well as a table of tool compatibility for different series LG. We took into account the features of refrigerators produced in 2018–2026, including models with linear compressor Inverterwhere sensor reconfiguration is required. If your refrigerator is older, check for service plugs under the hinges: in older versions they were often forgotten to be installed at the factory.

Before you start, answer the key question: Do you need to maintain the warranty? Hanging the door yourself may void the warranty LGif the product passport indicates that such work should be performed by a service center. Check this point in the documents or on the manufacturer's website.

1. Preparation: tools and safety

For work you will need:

• 🔧 Phillips screwdriver (preferably magnetic so as not to lose the screws).
• 🔨 Wrench 10 mm (for bottom door hinges in models LG GR-B207 i similar).
• 📏 Level (to check evenness after installation).
• 🧲 Magnet or tape (to temporarily fix the door during work).
• 🧴 Silicone grease (for processing hinges after rehanging).

⚠️ Attention: If your refrigerator is equipped with a system Smart ThinQ (for example, model LG GSX960), before starting work disconnect it from Wi-Fi through the application. Otherwise, the door opening sensor may work, and the refrigerator will start beeping or blocking functions.

Also prepare the workspace:

• 🚪 Clear a passage at least 1.5 wide m - the refrigerator door weighs 15–25 kg.
• 🧊 Remove all products and shelves from the door compartments (they may fall out when tilted).
• 🔌 Unplug the refrigerator and wait until the compressor will cool down (10–15 minutes).

2. Design features: what you need to know before you start

Refrigerators LG are divided into several types based on door design:

In models LG 2022–2026 with technology DoorCooling+ a fan is installed in the bottom hinge to distribute air evenly. When repositioned, it must be reinstalled on the opposite side, otherwise the refrigerator will not work correctly.

⚠️ Attention: If yours. the refrigerator is equipped with generator. ice (models LG LRMVC2306 and similar), before rehanging drain the water from the system and disconnect the water supply tube. Otherwise, when tilting the door, a leak may occur.

3. Step-by-step instructions: re-hanging the door

Let's look at the process using the example of a two-door refrigerator LG GA-B489 (similar for most models without a display. If you have a different modification, use this instruction as a guide). base, but check the user manual.

Take a photo of the location of the hinges and fasteners|Mark with a marker the position of the door relative to the body|Prepare a container for screws and parts|Wear gloves (the door may be cold)

-->

Step 1: Removing the top door (refrigerator compartment)

1. Open the door 90° and place a book or block under it (so as not to damage the floor).

2. Remove decorative plugs from the hinges (pry them up with a flathead screwdriver).

3. Unscrew the screws of the upper hinge (usually 3-4 pieces) and carefully remove the door, holding it by the bottom edge. Do not pull the handle! —it may come off.

Step 2: Transferring the hinges to the other side

1. On the opposite side of the case, find service holes (they are closed with plugs).

2. Move the top hinge to the new side using the same screws. Do not tighten them completely - first you need to align the door.

3. Repeat the process for the bottom hinge. In models with No Frost there may be a fastening for heating element under the bottom hinge - this is also needed. move.

Step 3: Door installation and adjustment

1. Place the door on the lower hinge, then align it with the upper one. Make sure that sealing rubber is not twisted.

2. Tighten the screws crosswise (first the top, then the bottom), checking the level. The door should open smoothly, without sagging.

3. Check the gap between the door and the body —it should be the same throughout the entire perimeter. (2–3 mm).

What to do if the door does not close tightly?

If after rehanging the door does not fit tightly, check:

1. Sealing rubber - it may have become deformed when removed. Warm it up with a hairdryer. (temperature 50–60°C) and restore the shape.

2. Hinges —they may have moved when tightened. Loosen the screws and adjust the position of the door again.

3. Magnetic seal (c models LG DoorCooling+) - it can be installed asymmetrically. Move it to the other side.

4. Nuances for models with a display and Smart ThinQ

Refrigerators LG display (series InstaView, ThinQ) require additional manipulations:

1. Disconnecting the power cable:

• 🔌 On the inside of the door, find display power connector (usually under the plastic cover).
• 🛠️ Carefully disconnect the cable by pulling the latch (do not pull the wires!).
• 🔄 Reinstall the cable on the other side, following the markings (L — left, R — right).

2. Reconfiguring sensors:

In models with Door Sense (for example, LG GSX961) after rehanging, you need to reset the door opening sensor settings:

1. Press and hold the button Ice Plus and Door Alarm simultaneously for 5 seconds.
2. Wait for the sound signal - this means that the sensor is calibrated.

⚠️ Attention: If after rehanging the display does not turn on or blinks, check polarity of the cable connection. In 80% of cases, the problem lies in the incorrect connection of the connector J1 (the designation is indicated on the board).

5. Typical mistakes and how to avoid them

Even with careful work, you can make mistakes that will lead to door sagging, loss of tightness or electronics failure. Here are the most common of them:

• 🔩 Untightened hinge screws → the door sags over time. Solution: use torque wrench (tightening torque 1.5–2 Nm).
• 🧲 Damaged sealing rubber → the refrigerator is wearing out. Solution: heat the rubber band with a hairdryer or replace (article number for LG: ADQ72916901).
• ⚡ Short circuit when working with the display → the control board burns out. Solution: unplug the refrigerator for 30 minutes before working with the cables.
• 🔄 Door sensor not reconfigured Sense → false alarms. Solution: reset as described in the previous section.

If after rehanging the refrigerator started to work loudly or does not coolcheck:

• 🌡️ Temperature sensors —they could move when the refrigerator is tilted.
• ❄️ No Frost evaporator —in models LG it sometimes touches the body if the door is installed incorrectly.

6. Reversing the door in Side-by-Side refrigerators

Models LG of the Side-by-Side format (for example LG GC-B247) have two massive doors, each of which weighs 25–30 kg. important:

1. Work with an assistant —it is almost impossible to hold the door and tighten the hinges at the same time.

2. Use safety belts. —they fix the door in the open position, preventing a fall.

3. Reconfigure the system Multi Air Flow —in these models the fans are located symmetrically, but their direction must be changed manually through the service menu.

⚠️ Attention: In refrigerators LG Side-by-Side with the function Water Dispenser before re-hanging be sure to turn off the water supply and drain the remaining water from the tube. Otherwise, when the door is tilted, water will enter the electronic unit.

After installing the doors, check:

• 🚪 Symmetrical gaps —they must be the same for both doors.
• 🔗 Opening synchronicity —the doors should move smoothly, without snagging.
• 💧 Operation of the dispenser —if the water flows weakly, check the tube for kinks.

7. How to check the result: leak test

After re-hanging the door, you need to make sure that the refrigerator is working correctly. Perform the following tests:

1. Fitness test: take a sheet of paper, clamp it between the door and the body and pull the sheet. pulls out without effort - the seal is installed incorrectly.
2. Temperature test: place the thermometer in the refrigerator compartment. After 2 hours the temperature should be +4...+5°C (at +4°C setting).
3. Noise test: listen to the operation of the compressor. Extraneous sounds (creaking, knocking) indicate displacement of internal parts.

If the refrigerator does not cool or works constantly, possible reasons:

• 🔧 The seal does not fit tightly → adjustment of the hinges is required.
• 🌡️ The temperature sensor has moved → return it to its place (in models LG it is attached with clips).
• ❄️ The No Frost evaporator is clogged → clean it with a vacuum cleaner (carefully, do not damage the ribs!).

FAQ: Frequently asked questions about re-hanging the LG door

Is it possible to re-hang the door of an LG refrigerator yourself if it is under warranty?

Technically yes, but the guarantee will be valid. canceledif the product passport indicates that such work should be performed by a service center. Check this point in the documents or with the official dealer. LGIn some cases, it is enough to save the receipt and photographs of the process for the guarantee to remain valid.

How long does it take to rehang the door?

For single-door models - 30–40 minutes, for Side-by-Side with a display - 1.5–2 hoursIf this is your first time doing this, allow extra time for adjustment and checking.

What to do if the LG refrigerator door sags after rehanging?

Causes of sagging:

• Hinge screws are loosely tightened → tighten them with a torque wrench.
• The hinges are deformed → replace them (original hinges for LG can be ordered by part code, for example ADH73176903 for the model GA-B489).
• The hinge axis is worn → lubricate it with silicone grease or replace it.

If the sagging is strong, the geometry of the door may have been damaged during installation. In this case, it is better to contact the service.

Do you need to reconfigure the electronic functions after rehanging?

Yes, in models with:

• Display — you need to reconnect the power cable.
• Door Sense —you need to calibrate the sensor (see section 4).
• Smart ThinQ —you may need to reconnect to Wi-Fi.

In refrigerators without electronics (for example, LG GA-B379) reconfiguration is not needed.

Where can I find service plugs for hinges if they are lost?

Plugs can be:

• Buy from an authorized dealer LG (cost ~200–300 rubles per set).
• Order at AliExpress (search for “LG door hinge caps”).
• Make it yourself from plastic or silicone (if the originals are temporarily unavailable).

⚠️ Do not use metal plugs - they can damage the body of the refrigerator during vibration.