The need to change the opening direction of the refrigerator door Beko often arises when remodeling a kitchen or moving to a new home. The standard factory configuration assumes opening from right to left, which is not always convenient in limited space. Fortunately, the design of most models of this brand allows you to carry out the rehanging procedure yourself, without calling a specialist.
The process requires care and a minimum set of tools, but is not technically difficult. It is important to understandthat violation of the sequence of actions can lead to damage to decorative panels or a violation of the tightness of the seal. In this article, we will analyze in detail how to safely change doors so that the equipment works correctly.
Preparation of the workplace and the necessary tools
Before starting any work, you need to clear the space in front of the refrigerator. You will need access to the device from all sides, so move refrigerator cabinet at least one meter away from the wall. Make sure that the floor is level and clean to prevent heavy structural elements from falling during dismantling.
To perform the rehanging operation, you will need a standard home handyman kit. Typically a flathead or Phillips head screwdriver and an 8mm or 10mm wrench or socket will suffice, depending on the model. Some modern modifications may have hidden fasteners, which will require a hex key.
Do not forget to prepare a soft backing, such as a blanket or thick cardboard, to place the removed door on the floor without the risk of scratching the facade or flooring. It is also worth having a container on hand for folding screws so as not to lose small parts during work.
⚠️ Attention: Before starting work, be sure to disconnect the refrigerator from the power supply! This is critically important, since when removing the doors, the wiring of the system
No Frostor the indication on the facade may be damaged.
☑️ Tools for replacing doors
Design features of refrigerator doors Beko
Refrigerators Beko are distinguished by a reliable hinge system, but their design may vary depending on the series. In most cases, the top and bottom hinges have symmetrical mounting holes on both sides of the case. This allows you to rearrange the elements to the opposite side without purchasing additional parts.
It is worth paying attention to the presence electronic control panel on the door. If your model is equipped with a display, the procedure is complicated by the need to disconnect the cables. In such cases, it is important to act extremely carefully so as not to damage the fragile contacts or the control board itself.
Models with the system Multi Air Flow or Neo Frost may have additional air ducts passing through the loop group. When removing the door, you must ensure that the air supply hoses are not kinked or pinched after reinstallation.
Step-by-step instructions: dismantling the top part
You should always start work with the top hinge, since it holds the bulk of the weight of the door. First, remove the decorative cap that hides the mounting bolts. Usually it is simply pryed off with a knife or flat-head screwdriver, but in some models it can be held on by latches.
After accessing the fasteners, loosen, but do not completely unscrew the upper bolts. At this stage, you will need an assistant to hold the door so that it does not fall. If you are working alone, you can use wedges or stops, but this is less safe for glass shelves inside.
Carefully unscrew the bolts and remove the top hinge. If the door has a magnetic lock or an opening sensor, disconnect the wire connectors. They can be located directly on the hinge or pass through the cavity of the door.
What to do if the bolts are rusty?
If the fasteners do not give way, do not use excessive force so as not to strip the threads. Treat the joint with a penetrating lubricant (such as WD-40) and wait 10-15 minutes. After this, the bolts should unscrew more easily.
Removing the door and working with the lower hinge
After releasing the upper part, carefully lift the door to remove it from the lower pin hinge. Place the removed element on the prepared soft substrate with the outer side facing up. Now you can begin to dismantle the lower support platform.
The lower hinge is often hidden by a plastic base or decorative strip at the bottom of the refrigerator. Remove this element to gain access to the mounting bolts. Unscrew them and remove the lower support.
Carefully inspect the removed parts. They may have special locating pins or bushings that need to be moved to new locations. Some models Beko use an asymmetrical design, where the left and right sides differ in the shape of the holes.
Compatibility table of tools and models
Different series of refrigerators may require a specific approach to fastening. Below is a table to help you navigate the types of connections for popular lines.
| Refrigerator series | Top hinge type | Bottom hinge type | Presence of wires |
|---|---|---|---|
| Beko RCNK | Open, 2 bolts | Hidden in the base | No (usually) |
| Beko CN | Closed with a lid | Open | Yes (sensor) |
| Beko GNE | Complex, 3 bolts | Reinforced | Yes (display) |
| Beko RCSK | Standard | Standard | No |
⚠️ Attention: In models with a display, the wires may be very short. When reversing the door to the other side, it may be necessary to extend the cable, since the standard length is sometimes not enough to connect to the control unit on the opposite side.
Installing hinges and hanging the door
The installation process begins with installing the lower support on the new side. Install the hinge into the holes provided for this purpose and secure with bolts. Do not tighten them all the way right away, leave a small gap for later adjustment of the door position.
Then install the door on the lower pin. Have an assistant hold the structure upright. Now you need to align the top of the door with the body and install the top hinge. Insert the bolts and start tightening them.
The final stage is tightening all fasteners. Do this sequentially, making sure that the door fits tightly and evenly around the entire perimeter. Install the decorative plugs and plastic covers in place.
Adjustment and checking the tightness
After installation, you need to check the tightness of the sealing rubber along the entire contour. The door should close with a characteristic bang, but without excessive force. If you notice gaps or distortions, you will need to adjust the height of the refrigerator legs or the position of the hinges. sealing gum along the entire contour. The door should close with a characteristic bang, but without excessive force. If you notice gaps or distortions, you will need to adjust the height of the refrigerator legs or the position of the hinges.
To check the tightness, you can use a simple test with a sheet of paper. Clamp the sheet between the door and the body at different points and try to pull it out. If the paper comes out too easily or, conversely, breaks, it means the pressure is uneven.
Plug in the refrigerator only after making sure that all wires are connected and the doors are closed. Let the equipment work for 2-3 hours without loading food to make sure that the compressor is working correctly and there are no problems with closing.
What to do if the door does not close completely?
Check whether there is anything in the way inside the refrigerator (protruding shelf, food packaging). Also make sure that the refrigerator is strictly horizontal. If the misalignment is caused by a broken hinge, the part may need to be replaced.
Is it possible to rehang a door if it has a logo on it?
Yes, you can. The logo Beko usually is a sticker or permanent design element. When repositioned, it will end up on the other side, which is normal for symmetrical models. There is no need to remove it.
Do you need to defrost the refrigerator before rehanging?
Complete defrosting is not necessary if you work quickly. However, if there is a lot of ice or food inside, it may fall out when the door is tilted. It is better to empty the refrigerator of food for safety and convenience.