Sealing rubber (or, as it is correctly called magnetic seal) - this is a key element of the refrigerator Vestel, responsible for the tightness of the chamber. Over time, it loses elasticity, becomes cracked or moves away from the housing, which leads to increased energy consumption and even compressor breakdown. If you notice that the door does not fit well, ice forms on the walls, and the motor works without stopping, it’s time to change the seal. loss of cold, increased energy consumption and even compressor breakdown. If you notice that the door does not fit well, ice forms on the walls, and the motor runs nonstop, it’s time to change the seal.
In this article you will find step-by-step instructions on replacement rubber bands on refrigerators Vestel (including popular models Vestel NF 330 IX, Vestel NF 420 IX, Vestel BK 187 and others). We will look at how to properly remove the old seal, select a new one, install it without distortions and check the tightness. You will also find out what errors during replacement lead to repeated peeling of the rubber after 1-2 months and how to avoid them.
Signs of wear on the rubber seal on the refrigerator Vestel
Before you start replacing, make sure that the problem is in the seal. Here are the key symptoms:
- 🔍 Visible damage: cracks, tears, deformation of the rubber (especially in the corners of the door).
- ❄️ Ice on the back wall: if the refrigerator is No Frost, and ice still forms - check the fit of the door.
- 💨 Cold air flow with the door closed (you can feel it with your hand).
- 📈 Increased energy consumption: the compressor works almost without pauses, the electricity bill has increased.
- 🚪 The door opens spontaneously or closes with difficulty.
If at least 2-3 signs match, the seal definitely requires replacement. Vestel uses standard magnetic rubber bands, which can be found in specialized stores or ordered by article number (for example, for model NF 330 IX suitable seal with code VES-330-U).
⚠️ Attention: Do not confuse the wear of the seal with a malfunction of the door hinge. If the door is sagging or skewed, first adjust the hinges - this can solve the problem without replacing the rubber band.
How to choose a new rubber band for Vestel refrigerator
80% of success depends on the correct choice of seal. Here are the criteria you should pay attention to:
| Parameter | Recommendations | Notes |
|---|---|---|
| Model refrigerator | Check the exact model (located on the sticker inside the chamber or on the back). | For Vestel BK 187 and Vestel NF 420 IX different seals are suitable! |
| Material | Original - food grade silicone with a magnetic insert. Cheap PVC substitutes quickly tan. | Check the certificate of conformity (there must be a marking FDA or LFGB). |
| Method of fastening | In a groove (slot-in) or with glue/screws. U Vestel usually a groove fastening. |
If there is no groove, take an elastic band with an adhesive base (for example, 3M VHB). |
| Length | Measure the perimeter of the door along the inner edge (for Vestel usually 1.8–2.2 m). | It is better to take with a reserve 10–15 cm for adjustment. |
Where to buy:
- 🛒 Official service centers Vestel - original spare parts, but more expensive.
- 🌍 Online stores (for example,
Zapchasti365.ru,Holodilnik.ru) - wide range, available reviews. - 🏠 Household goods stores - universal elastic bands (suitable for temporary replacement).
⚠️ Attention: If you buy a universal elastic band, check it magnetic properties. A weak magnet will not press the door tightly, and the problem will return in a few months.
Tools and materials for replacing the rubber band
For work you will need:
A Phillips screwdriver (for dismantling the door, if necessary)
A construction hair dryer (to soften old glue)
A stationery or shoe knife (to remove residual sealant)
Silicone sealant or glue Moment Crystal (if the fastening is not grooved)
Screws 3×16 mm (for additional fixation, if necessary)
Solvent (white spirit or acetone) for degreasing
Ruler or tape measure (for measuring a new rubber band)-->
If the seal is attached to the groove, additional materials are not needed. If it is glued, prepare degreaser And glue. For models Vestel with self-tapping screws (for example, Vestel CMN 5090), new fasteners may be required - old ones often rust or break during dismantling.
Safety tip: Before starting work unplug the refrigerator and defrost it (if there is ice). It is more convenient to work with the seal at room temperature - the elastic band becomes more elastic.
Step-by-step instructions: how to remove the old rubber band
Disassembly is the most important step. If the door or body is damaged, the nueva rubber will not lie flat. Follow the algorithm:
- Remove the door (optional). To do this, unscrew the hinges (usually 3-4 screws). data-i="146">Remove the door
- Find the mounting location:
- If the rubber is inserted into the groove, pry it out with a knife or flat screwdriver.
- If it is glued, heat it with a hairdryer (temperature 60–80°C) and gently pull.
- If it is screwed on with self-tapping screws, unscrew them starting from the corners.
On models Vestel with a system No Frost (for example, Vestel NF 520 IX) the seal is often attached in combination: part in the groove, part on the glue. In this case, first remove the elastic from the groove, and then separate the glued sections.
What to do if the elastic is stuck to the door?
If the seal does not come off even after heating with a hairdryer, use a fishing line or string. saw back and forth, as when cutting foam plastic. The main thing is not to scratch the plastic of the door!
Installing a new sealing rubber band
Now we move on to installation. uniform fit. Instructions: distortions and ensure an even fit. Instructions:
- Try on the elastic data-i="170">only at the junction along the perimeter of the door. If it is longer, cut only at the junction (usually at the bottom). The joint should be at an angle of 45° for a tight connection.
- Start installation from the top corner:
- For groove fastening: insert the seal into the groove, starting from the corner, and gradually tuck it around the entire perimeter. Use a flat-head screwdriver to push the elastic deep into the groove fastening
- For adhesive fastening: apply a thin layer of glue to the door, press the elastic and secure with masking tape for 10-15 minutes.
- For the groove seal: use a special one connecting profile (included) or glue the ends superglue.
- For adhesive: coat the joint with sealant.
- Visual inspection: close the door and look at the cracks. If light is visible, the seal is uneven.
- Test with paper:
- Insert a sheet of paper between the door and the body.
- Close the refrigerator and try to pull out the sheet.
- If the paper comes out easily, the fit is weak.
- Checking the magnet: when the door is closed, the seal should “stick” with a characteristic click. If the magnet is weak, the elastic band will come off.
On models Vestel with double door (for example, Vestel Side-by-Side) the seal is changed separately on each sash. Start with the top door, then move to the bottom.
Checking the tightness after replacement
Installing the rubber is half the battle. Now you need to make sure that it performs its function. Carry out 3 tests:
If the tests fail:
- 🔧 Tighten the screws (if the mount is on them).
- 🔥 Warm the elastic with a hairdryer - it will become softer and it will fit better.
- 📏 Check the door geometry. If it is skewed, adjust the hinges.
Common mistakes and how to avoid them
Even experienced craftsmen sometimes make mistakes that lead to repeated replacement of the gum. Here TOP-5 mistakes and ways to prevent them:
| Error | Consequences | How to avoid |
|---|---|---|
| Incorrect length rubber bands | Cracks at the joints, violation of tightness | Measure the perimeter along the inner edge of the door, and not using the old rubber band. |
| Use of non-original seal | Rapid wear, weak magnet, cracks after 3-6 months | Buy a rubber band with marking Vestel OEM or proven analogues (for example, Sibir). |
| Glue applied in a thick layer | The elastic band "floats" and is not fixed in the groove | Use glue pointwise (every 10–15 cm) or a special sealant for refrigerators. |
| The old one has not been removed glue | The new rubber band comes off, gaps form | Clean the surface with solvent and sandpaper (grain size 120–180). |
| Installation at low temperature | The rubber band becomes tan and does not lie down exactly | Work in a room with a temperature not lower than +18°C. |
If after replacement the seal still comes off, check magnetic insert. Over time, it may demagnetize - in this case, only replacing the rubber band with a new one will help.
FAQ: Frequently asked questions about replacing an elastic band on Vestel
Is it possible to restore an old elastic band without buying a new one?
A temporary solution is to heat the seal with a hairdryer (60–80°C) and lubricate with silicone grease (for example, WD-40 SpecialistThis will restore elasticity for 1-2 months, but in case of cracks or tears, only replacement will help.
Which glue is best to use for gluing the seal?
Optimal options:
Moment Crystal—transparent, moisture-resistant.3M VHB—double-sided tape for permanent fixation.Soudal Fix All—hybrid adhesive-sealant (suitable for plastic).
How much does it cost to replace an elastic band at a Vestel service center?
The price depends on the model and region:
- The elastic band itself: 1,200–3,500 ₽ (the original is more expensive than the universal one).
- The work of a master: 1,500–2,500 ₽.
Total: 2 700–6 000 ₽2–3 times cheaper.
How long should the seal be checked after replacement?
Control checks:
- Immediately after installation (test with paper).
- After 24 hours (check for peeling).
- After 1 week (assessment of tightness based on ice and compressor operation).
If there are no problems within a month, the replacement was successful.
Is it possible to change the rubber band without removing the door?
Yes, but it is less convenient. If the seal is in the groove, you can replace it on the fly. If it is glued or screwed, it is better to remove the door - it is easier to clean the surface and lay the new rubber evenly.