The rubber seal (or door rubber) is a key element of the refrigerator, responsible for the tightness of the chamber. Over time, it loses elasticity, cracks or deforms, which leads to increased energy consumption and even compressor breakdown. In refrigerators loss of cold, increased energy consumption and even compressor breakdown. In refrigerators Ariston Hotpoint (including series models HB, HBM, HHT), replacing the seal is a task that you can do yourself, saving on calling a technician.
In this article you you will find detailed instructions with videohow to remove the old rubber band, select a new one (including original articles for Hotpoint-Ariston), install it correctly and check the tightness. We will also analyze typical errors that lead to repeated repairs after 1-2 monthsand give advice on extending the service life of the seal.
If your refrigerator has become worse at freezing, a mark appears on the door condensation, and the motor runs almost non-stop - with a 90% probability the problem is in the seal. Next, you will learn how to diagnose a malfunction and fix it in 1-2 hours.
Signs of seal wear: when is it time to change?
The first step is to make sure that the problem is in the rubber band and not in other components of the refrigerator (for example, in thermostat or No Frost system). Pay attention to the following symptoms:
- 🔍 Visible damage: cracks, tears, traces of mold or peeling of rubber from the base.
- 💧 Condensation on the door or under the refrigerator - a sign warm air getting inside.
- ❄️ Ice on the back wall (in models without No Frost) due to constant moisture ingress.
- 📈 Increased energy consumption: the compressor runs longer, trying to compensate for the loss cold.
- 📏 Gaps between the door and the bodywhich are visible when the door is closed (checked with a sheet of paper).
Simple test: take a sheet of paper, close the refrigerator door, holding the sheet between the seal and body. If the sheet is easily pulled out, the rubber band is not sealed. Normally, it should hold tight or tear when you try to pull it out.
⚠️ Attention: If the seal is deformed in only one place (for example, in a corner), do not rush to change it completely. Sometimes it is enough restore the shape to use a hairdryer (heat the elastic band to 60–70°C and give it the correct shape with your hands). This is a temporary solution, but can extend the service life by 3-6 months.
On models Hotpoint-Ariston with electronic control (for example, HBM 1852 or HHT 2521), wear of the seal can cause an error E1 or E2 on the display - this is a signal about a violation of the temperature regime. In mechanical models, the sign will be a constantly running compressor without shutdown cycles.
Choice of seal: original vs universal
80% of the success of the repair depends on the correct selection of rubber. For refrigerators Ariston Hotpoint there are two options:
- Original seals from the manufacturer (for article numbers, see the table below). They are ideal in size and shape, but are more expensive (from 2,500 to 5,000 ₽).
- Universal elastic bands (for example, from Sibir or Stinol). Cheaper (800–1,500 ₽), but require adjustment in length and may fit worse in the corners.
| Refrigerator model | Sealant article number | Approximate price (2026) | Notes |
|---|---|---|---|
| Hotpoint-Ariston HBM 1301/1302 | C00348956 |
3 200 ₽ | Suitable for models with a height of 130–140 cm |
| Hotpoint-Ariston HHT 2521 | C00348957 |
4 100 ₽ | For two-chamber models with No Frost |
| Ariston HB 1852 | C00348958 |
2 800 ₽ | Seal with magnetic insert |
| Universal (for most models) | Sibir 2100-0001 |
1 200 ₽ | Requires trimming and gluing corners |
Where to buy:
- 🛒 Official service centers Hotpoint-Ariston - guarantee of original quality, but high price.
- 🌍 Online stores (for example, 220-Volt, All-ZIP) - often there are discounts up to 20%.
- 🔧 Stores of spare parts for household appliances - you can choose a universal analogue.
⚠️ Attention: When purchasing a universal seal, please contact attention to the width of the groove (must match the original) and presence magnetic insert (if it was in an old elastic band). Without a magnet, the door may not close well.
If you are not sure of the choice, take a photo of the old seal with a ruler next to it and show it to the seller - he will help you choose an analogue. You can also use search by article on spare parts websites by entering the model of your refrigerator.
Preparation for replacement: tools and safety measures
Before starting work, unplug the refrigerator and remove all food. If the model is with No Frost, wait 1-2 hours for the ice on the evaporator to melt - this will make it easier to access the seal fasteners.
Required tools:
- 🔧 Screwdriver (Phillips or flat - depends on the fastenings).
- 🔨 Screwdriver (if the seal is attached with self-tapping screws).
- 🧴 Silicone sealant or glue
Moment Crystal(for gluing corners). - 📏 Ruler or tape measure (to measure the length of a universal elastic band).
- 🧽 Warm water and detergent (to clean the groove from old glue).
Safety measures:
- ⚡ Do not turn on the refrigerator until you complete the replacement and do not check the tightness.
- 🧤 Wear gloves - the old seal may be sharp around the edges.
- 🚫 Do not use a knife to pry the rubber band - you can damage the plastic of the door.
☑️ Preparation for replacement seal
If the seal is attached to double-sided tape (often in budget models), prepare new tape 10–15 mm wide. For models with groove fastening (for example, Hotpoint-Ariston HBM 1852) no additional glue is needed - the elastic is inserted into the groove and fixed due to the shape.
Step-by-step instructions: how to remove the old seal
The dismantling process depends on the type of fastening. In refrigerators Ariston Hotpoint there are three options:
- Self-tapping (more often in older models).
- Grooved fastening (the rubber band is inserted into a special groove on the door).
- Glue or double-sided tape (in budget models).
Removing the seal using self-tapping screws:
- Carefully unscrew all the screws around the perimeter of the door (usually they are hidden under the decorative trim).
- Remove the rubber band by pulling it towards you. If it is additionally glued, pry it off with a plastic spatula.
- Clean the groove from residual glue and dust.
Removing the seal with a groove fastening:
- Find the beginning of the elastic (usually in the upper corner of the door).
- Carefully pull the seal towards you, pulling it out of the groove. If it fits tightly, use a screwdriver, but do not use force - you can break the plastic.
- After removal, check the groove for cracks. If there are any, cover them with sealant.
Removing the seal on the glue:
- Pry up the rubber in one place and slowly tear it off, heating it with a hairdryer (a temperature of 50–60°C will make the process easier).
- Remove any remaining adhesive with a solvent (for example,
White spirit), then wipe the surface with alcohol.
What to do if the seal is tightly glued?
If the rubber does not come off even after heating, try cutting it off with a stationery knife, leaving a thin layer of rubber on the door. Then remove the residue with sanding paper (grit 120–180) and degrease the surface.
In models Hotpoint-Ariston with magnetic insert (for example, HHT 2521) be careful - the magnet may remain in the groove. Remove it with tweezers so as not to damage the new rubber during installation.
Installing a new seal: nuances for Ariston Hotpoint
The installation process depends on the type of fastening. Let's consider each option in detail.
1. Installation with screws:
- Attach the new seal to the door, aligning the holes for the screws.
- Start from the top corners, then fix the bottom and sides.
- Do not overtighten the screws - the elastic should remain elastic.
2. Installation in the groove:
- Start from the top corner, inserting into the groove corner of the seal (usually marked with an arrow or mark).
- Gently press the elastic around the entire perimeter using a flat screwdriver or a special spatula.
- In the corners you can apply a little silicone sealant for additional fixation.
3. Installation with glue:
- Apply glue
Moment Crystalor silicone sealant to the door groove. - Apply the seal, starting from the top corner, and press firmly.
- Secure the elastic band with masking tape for 12-24 hours until the glue has dried.
For models with No Frost (for example, Hotpoint-Ariston HHT 2521) after installing the seal, check the operation of the fan - it should rotate freely without touching rubber band.
After installation, close the door and check for gaps. If the rubber band bulges in some places, heat it with a hairdryer (temperature 60–70°C) and shape it into the correct shape with your hands.
Checking for tightness and testing
After replacing the seal, you must make sure that the door closes tightly. To do this:
- Visual inspection: close the door and see if there are any gaps. In the corners, the elastic should fit snugly.
- Test with a sheet of paper: as in diagnostics, clamp the sheet between the seal and the body. If it pulls out without effort, the seal is broken.
- Checking the temperature: turn on the refrigerator and after 2-3 hours check the temperature inside (should be +4...+6°C in the refrigerator compartment).
If, after replacing the seal, the refrigerator Ariston Hotpoint continues to work without stopping or an error appears on the display E1, the following problems are possible:
- 🔄 Incorrect installation: the seal is twisted or not fully inserted into the groove.
- 🧲 There is no magnetic insert (if it was in the original).
- 🔧 The groove on the door is damaged - plastic repair is required.
In models with electronic control (for example, HBM 1852) after replacing the seal, it may be necessary resetting errors. To do this, unplug the refrigerator for 5–10 minutes, then turn it on again.
Typical mistakes and how to avoid them
Even with careful replacement of the seal, mistakes can be made that will lead to repeated repairs. Here are the most common ones:
| Error | Consequences | How to avoid |
|---|---|---|
| Incorrect selection of seal (wrong article or size) | Cracks, bad tightness, rapid wear | Check the article number according to the refrigerator model or take the old rubber band with you to the store |
| Using superglue instead of silicone sealant | The rubber band becomes stiff and cracks | Use only elastic adhesives (for example, Moment Crystal) |
| Incomplete cleaning of the groove from old glue | The new seal does not hold well, comes off in the corners | Remove carefully remaining adhesive with a solvent and degrease the surface |
| Tightening the screws too tightly | Deformation of the seal, cracks | Tighten the screws without excessive force |
Another common problem is the door is misaligned after replacing the seal. This happens if the rubber is installed unevenly or the magnetic insert is displaced. To correct:
- Check whether the seal fits evenly around the entire perimeter.
- If the door is sagging, adjust the hinges (in models Hotpoint-Ariston this is done with a hex key).
In refrigerators No Frost after replacing the seal, it may appear excess condensation on the walls. This is normal in the first 1-2 days - the equipment adapts to the new level of tightness. does not disappear, check whether the rubber band is blocking the ventilation holes.
Video instructions: replacing the seal on Ariston Hotpoint
For clarity, we recommend watching a video with step-by-step replacement of the seal Below is a selection of proven videos for different ones. models:
- 🎥 For models with groove fastening (for example, HBM 1301): YouTube link (the process of removing the old rubber band and installing a new one without glue is shown).
- 🎥 For models with self-tapping screws (for example, HB 1852): Link to YouTube (demonstration of correct tightening of fasteners).
- 🎥 For refrigerators with No Frost (for example, HHT 2521): YouTube link (features of working with a magnetic insert).
Pay attention to the following points from the video:
- How to properly remove the seal from the groovewithout breaking the plastic.
- Technique heating the elastic with a hair dryer for better elasticity.
- Method checking the tightness using a flashlight (shine inside a closed refrigerator - if light is visible, there is slots).
If in your model Ariston Hotpoint the seal is attached in a non-standard way (for example, with latches), look for a video specifically for your series. For example, for Hotpoint-Ariston BCB 33 the process will be different from HBM 1852.
⚠️ Attention: In some videos, craftsmen use hammer to drive the seal into the groove. For refrigerators Ariston Hotpoint this method is not recommended - you can damage the plastic of the door. It is better to use a wooden spatula or the blunt edge of a screwdriver.
FAQ: answers to frequently asked questions
Is it possible to restore an old seal without buying a new one?
Yes, if the damage is minor Methods of restoration:
- Warming with a hairdryer. (60–70°C) and shaping by hand.
- Treatment with silicone grease to restore elasticity.
- Gluing cracks with special glue for rubber (for example,
Loctite 406).
However, these are temporary measures - after 3-6 months you will still need a sealant change.
How much does it cost to replace a seal in a service center?
Cost of work in official services Hotpoint-Ariston:
- Replacement of a seal - from 1,500 to 3,000 ₽ (excluding the cost of the rubber band).
- Tightness diagnostics - 500–800 ₽.
Total with a spare part will be 4,000–8,000 ₽. Independent replacement costs 2–3 times cheaper.
How often do you need to change the seal?
The service life of the original seal Ariston Hotpoint is 5–10 years. Wear is affected by:
- Frequency of door opening.
- Temperature and humidity in the room.
- Quality of care (regular cleaning and lubrication prolongs service life).
With careful use and proper care replacement may not be necessary at all.
What to do if, after replacing the seal, the refrigerator begins to make noise?
Probable reasons:
- The rubber band touches the fan (in models with No Frost).
- The door is skewed due to uneven installation seal.
- The magnetic insert has moved and is preventing closure.
Solution: check the symmetry of the door, adjust the hinges if necessary.
Is it possible to use a seal from another brand (for example, from Indesit or Samsung)?
Theoretically it is possible, but only if:
- The method of fastening matches. the shape of the groove and method of fastening.
- The width and thickness of the elastic are identical to the original.
- There is a magnetic insert (if it was in the original).
It is better to select a seal according to the article number or take a universal one with the possibility of adjustment.