The sealing gum (or, as it is also called, magnetic seal) is the part of the refrigerator Indesitthat is responsible for the tightness of the chamber. Over time, it wears out: it loses elasticity, becomes cracked, or moves away from the door, allowing warm air to pass through. The result is increased energy consumption, frost on the back wall and food spoilage. Fortunately, you can replace it yourself, without resorting to the services of a service center.
In this article we will analyze the whole process from A to Z: how to choose the right rubber band for your model Indesit, dismantle the old one without damaging the door, install a new one and check the tightness. You will also learn what mistakes beginners most often make and how to avoid them. If your refrigerator belongs to the series C 138 NF, B 18 FNF, T 16 F or other popular lines of the brand, the instructions will be suitable taking into account small nuances.
The average replacement time is from 40 minutes to 1.5 hours, depending on experience. The cost of a new rubber band varies from 800 to 2,500 rubles (for 2026), which is 3–5 times cheaper than calling a specialist. Ready to get started? Then let's start with preparation!
1. Signs of seal wear: when is it time to change?
It is not always obvious that the problem is in the rubber band. Sometimes users blame problems on the thermostat or compressor, wasting money on unnecessary diagnostics. To avoid mistakes, check these 5 key symptoms:
- 🔍 Condensation on the door - if drops of water regularly appear on the outside of the refrigerator, this is a sign of depressurization. Warm air penetrates inside and condenses on a cold surface.
- ❄️ Ice on the back wall —the seal allows air to pass through, moisture settles in the form of frost. It is especially noticeable in models with a system No Frost (for example, Indesit ITF 118 W).
- 💡 Constant operation of the compressor - if the motor almost does not turn off, this may mean that the refrigerator is trying to compensate for the loss of cold.
- 📏 Visible damage to the elastic band - cracks, tears, deformation or separation from the door. Often found in corner areas.
- 🧊 Products spoil faster - especially in the freshness area or on door shelves, where the temperature is higher than normal.
A simple test for tightness: take a sheet of paper (for example, a banknote), close the door, holding it between the seal and the body. If the sheet is easily pulled out, the rubber band does not fit tightly. Check this around the entire perimeter.
⚠️ Attention: In refrigerators Indesit with electronic control (series EWS, BIAA) it is faulty. the seal may cause an errorF04orF05—temperature sensor failure. Before replacing the rubber band, reset the error by unplugging the refrigerator for 10 minutes.
2. Choosing a sealing gum for Indesit: original vs analogues
The first thing you need to do is to identify exact model the label with the marking is usually located on the inside wall of the chamber, on the door or on the back of the case. Look for the type of markings Indesit C 132 G NF or BIA 18 KIf the label has worn off, look in device passport or. top bar inside the refrigerator.
Seals for Indesit are divided into three types:
- 🔄 Universal - suitable for most brand models. standard profile and magnetic insert. Examples: 5301318699, C00198767.
- 📌 Specialized - designed for specific series (for example, for two-chamber Indesit ITF or SBIAAThey have a unique groove shape.
- 🔧 Analogs from third-party manufacturers - cheaper than the originals by 30–50%, but may differ in hardness. Popular brands: Samsung (compatible with some models), Beko, Ardo.
| Refrigerator model | Article number of the original seal | Average price (2026) | Analogues (articles) |
|---|---|---|---|
| Indesit C 138 NF | C00198767 |
1 200–1 500 ₽ | 5301318699, 481241866921 |
| Indesit B 18 FNF | C00208304 |
1 400–1 800 ₽ | 5301318698, 481241866920 |
| Indesit T 16 F | C00198768 |
900–1 200 ₽ | 5301318697 |
| Indesit ITF 118 W | C00306300 |
1 800–2 200 ₽ | No complete analogues |
Where to buy:
- 🛒 Official service centers Indesit - original guarantee, but the price is higher.
- 🌍 Online stores (for example, 220-Volt, MVideo, Yandex Market) - convenient to compare prices.
- 🔧 Stores of spare parts for household appliances - there are often universal options available.
⚠️ Attention: When purchasing, check that the seal is solid (not glued together from pieces) and has magnetic insert. Some cheap analogues lose their shape after 6 months.
3. Preparation for replacement: tools and safety measures
Before starting work unplug the refrigerator and remove all the food. If the freezer is separate, you can leave it on, but you will have to keep the refrigerator door open. 1-2 hours for the plastic to become more pliable (especially important for models with No Frost).
Required tools:
- 🔧 Phillips screwdriver (PH2) or flat - for dismantling fasteners.
- 🔨 Plastic spatula or blunt carpenter's spatula - to pry off the old rubber band.
- 🧴 Silicone grease or
WD-40- for processing the grooves (if the rubber band is stuck). - 🧲 Magnet (optional) - to check the adhesion force of the new seal.
- 📏 Tape measure or ruler - for measuring the length of the elastic band (if you buy a universal one).
- 🧴 Glue
"Moment"or sealant (only for models with a glued seal).
Also prepare:
- Warm water and soap - to clean the grooves from dirt and glue residues.
- A hair dryer (optional) - if the rubber band is “stuck” to the plastic.
- Gloves - to avoid getting hurt on sharp edges metal.
If your refrigerator is Indesit with two doors (model SBIAA 18 K, BIAA 20 K), start with the top chamber - it is easier to track the correct installation. For single-chamber (C 132 G, T 16 F) the order is not important.
Make sure the refrigerator is unplugged|
Remove all products and shelves from the door|
Prepare tools (screwdriver, spatula, lubricant)|
Check the integrity of the new seal (for cracks)|
Clean the door grooves from dirt and old glue-->
4. Removing the old rubber: step-by-step instructions
The most important step is removing the worn seal. door plastic. Indesit fastening can be:
- 🔩 On self-tapping screws (more often in older models, for example Indesit C 138 before 2015).
- 🧩 In grooves (modern refrigerators, for example, ITF 118 W).
- 🎨 On glue (rarely, usually in budget series).
Sequence of actions:
Open the door and find fastening points the seal. In models with self-tapping screws, they are visible from the outside (along the perimeter of the door). In grooved versions, the elastic “sits” in the recess of the plastic.
If the fastening is on self-tapping screws, carefully unscrew them with a screwdriver, starting from the top corner. Do not pull the elastic by force - this can tear off the plastic latches doors!
For groove fastening, pry the seal with a plastic spatula in one of the corners and slowly pull, releasing it along the entire perimeter. If the gum is “stuck”, treat the grooves
WD-40and wait 5-10 minutes.Remove any remaining glue or dirt from the grooves using warm water and a brush. Dry the surface with a hairdryer or napkin.
The most difficult thing is to remove the seal in corner areas - there it often sticks. If the rubber band breaks during dismantling, don’t worry: you change it anyway. The main thing is not to damage the door itself.
What to do if the screw breaks when unscrewing?
If the head of the screw remains inside, use extractor (a special tool for removing broken fasteners). An alternative is to drill out the self-tapping screw with a drill with a thin drill bit (⌀ 2–3 mm), then insert a new one. As a last resort, you can carefully break off the plastic around the fastener and attach a new rubber band with glue.
5. Installing a new sealing gum
Now we move on to installation. Here it is important to follow three rules:
- The seal must sit tightly, without gaps.
- The corners must be carefully docked (without distortions).
- The magnetic insert should attracted to the body evenly around the entire perimeter.
Instructions for models with groove mounting (most modern Indesit):
Start with upper corner the door. Insert the end of the seal into the groove and gently press, moving down.
Do not pull the elastic in the corners - it should lie down naturally, without tension. If necessary, trim off the excess with a utility knife (but usually the original seals fit perfectly).
After installation along the entire perimeter, check that the elastic does not bristle and does not come out of the groove. If necessary, adjust it with a spatula.
Close the door and check the fit with a piece of paper (as at the beginning of the article). If the paper falls out somewhere, tighten the seal in that place.
Instructions for models with screws (old Indesit):
Attach a new rubber band to the door, aligning the holes for the screws with the fastening ones dots.
Tighten the screws diagonally (first the top left, then the bottom right, etc.) to avoid distortion.
Do not tighten the screws too much - this can damage the plastic doors.
Instructions for models with glue (rarely):
Apply a thin layer of glue
"Moment"or sealant to the door groove.Press sealant and secure it with masking tape for 1-2 hours.
Do not use the refrigerator for 12 hours to allow the glue to dry completely.
⚠️ Attention: In refrigerators Indesit with double door (models SBIAA, BIAA), first install the seal on upper chamber, then on the bottom. This will help avoid distortion. doors when closing.
6. Checking the tightness and testing
After installing the new seal, you need to make sure that it works correctly. Here are 4 testswhich are worth doing:
- 📄 Test with a sheet of paper - clamp it between the door and the seal around the entire perimeter. The sheet should hold tightly without falling out.
- 🧲 Test with a magnet —if the elastic has a magnetic insert, bring a small magnet to the door. It should be attracted evenly, without “dips.”
- 🕒 Closing time test —open the door 45° and release it. close on your own under weight (if the seal is working).
- 🌡️ Temperature test - turn on the refrigerator and after 2-3 hours check the temperature in the chamber (should be +4...+6°C If it is higher -). the seal allows air to pass through.
If the refrigerator is equipped with display (models Indesit EWS 61052, BIAA 13), after replacing the seal you may need reset settingsTo do this:
- Disconnect the refrigerator from the mains for 1 minute.
- Turn on and press the buttons
"Super Cool"and"Super Freeze"(if any) at the same time to 5 seconds. - Wait until the display blinks - this means that the settings have been reset.
On the first day after replacement, keep an eye on:
- Condensation on the door - there should not be any.
- Compressor noise - it should work in cycles (turn on and off), and not constantly.
- The temperature in the chamber - use a separate thermometer to check.
⚠️ Attention: If, after replacing the seal, the refrigerator becomes make more noise, check whether the door is warped. Sometimes the new rubber can shift the closing geometry. Adjust the door hinges. using a hex key (instructions are in the device passport).
7. Common mistakes and how to avoid them
Even with careful replacement, you can make mistakes that will nullify all efforts. Here TOP-5 misses and ways to prevent them:
- 🔄 Wrong choice. seal - if the rubber is too hard or, on the contrary, soft, it will not seal the chamber. Always check the article number with the model of the refrigerator.
- 📏 Uneven tension —if the seal is too tight in one place, it will leak air in another. Distribute it evenly, without distortions.
- 🧴 Ignoring cleaning of the grooves —remnants of old glue or dirt prevent a tight seal. Always clean and degrease the surface before. installation.
- 🔩 Tightening the screws too much —this leads to cracks in the plastic of the door. Tighten the fasteners with moderate force.
- ❄️ Failure to check the tightness —many people forget to test the seal after installation. Use the test. with a sheet of paper or a magnet!
Another common problem is when opening the door. This is normal in the first days, but if the sound does not pass, treat the seal creaks of the new rubber when opening the door. This is normal in the first days, but if the sound does not pass through, treat the seal silicone grease (do not use oils - they are spoil the rubber!).
If after replacing the seal the refrigerator Indesit became turn on more oftencheck:
- Correct installation of the rubber band (are there any gaps).
- Room temperature - if above +30°C, the compressor works more intensely.
- Thermostat settings - it may have gone wrong when turned off food.
8. Caring for the seal: how to extend its service life
To make the new rubber last longer, follow these recommendations:
- 🧼 Regular cleaning —wipe the seal with warm water and soap or a weak solution of vinegar (1:1) once every 2-3 months. Avoid. abrasive detergents!
- 🧴 Lubricant - apply to the rubber band once every six months silicone grease (sold in car dealerships).
- 🚪 Careful opening —do not pull the door by the seal, open it by the handle. This will prevent deformation.
- 🌡️ Temperature control —do not place the refrigerator next to the stove or radiator. rubber wear.
The average service life of the seal is 5–7 years. But with proper care, it can last 10 years. Pay attention to the first signs of wear (condensation, ice) and react quickly - this will save you money on repairs. compressor.
If the seal still begins to crack, but a complete replacement is not yet required, you can temporarily repair it:
- Small cracks seal food-grade silicone (sold in hardware stores).
- Glue the peeled areas
"Moment"(only outside!). - If the elastic band is deformed, immerse it in hot water (60–70°C) for 5–10 minutes, then straighten it and let it cool.
⚠️ Attention: In refrigerators Indesit with a system No Frost (for example, ITF 118 W) the seal wears out faster due to frequent opening of the door for air circulation. Check its condition every six months!
FAQ: Answers to frequently asked questions
Is it possible to change the seal only on the freezer compartment if the problem is there?
Yes, if in your refrigerator Indesit the freezer and refrigerator compartments have separate seals (as in models SBIAA 18 K or BIAA 20 K). To do this, remove only the upper or lower elastic band, depending on the design. In single-chamber refrigerators (for example C 132 G), there is only one seal for the entire door - you will have to change it completely.
How much does it cost to replace a seal at a service center?
Cost of work in official services Indesit (for 2026 year) ranges from 1,500 to 3,000 rubles, plus the price of the elastic band itself. The total comes out to 2,500–4,500 rubles. Self-replacement costs 3–5 times less. However, if you are not confident in your abilities (for example, you are afraid of damaging the door), it is better to turn to professionals.
What to do if the new seal is not magnetic?
This means that there is no magnetic insert in the rubber band or it is damaged. Return the seal to the seller - it is defective. In high-quality original parts for Indesit magnetic tape is sewn along the entire perimeter. If you buy an analogue, check with the seller for the presence of a magnet. Without it, the seal will be worse.
Can the seal be washed in a washing machine?
No! Rubber and magnetic insert are not machine washable. The maximum that can be done is to wash the seal in warm water (up to 40°C) with a mild detergent, then air dry. Do not use hot water, bleach or aggressive chemicals - this destroys the structure of the rubber.
Why did the refrigerator begin to freeze more after replacing the seal?
This is a temporary phenomenon. The new seal provides a better seal, so the compressor works harder to reduce the temperature to the set temperature. After 1–2 days the regime will stabilize. If the frost is too severe (below -20°C in the refrigerator compartment), check the thermostat settings - perhaps they were lost when the power was turned off.