Replacing the rubber seal on the Pozis refrigerator: a detailed guide with photos

Sealing rubber (or door seal) is the key element responsible for tightness refrigerator Pozis. Over time, it wears out: it loses elasticity, becomes cracked, or moves away from the housing, which leads to increased energy consumption, ice formation on the back wall, and even compressor failure. If you notice that the door no longer fits tightly, and visible defects have appeared on the seal, it’s time to replace it.

In this article we will look in detail at how to change the rubber band on the refrigerator Pozis with your own hands: from choosing a suitable seal to the final check tightness. You will learn what tools you will need, how to properly remove the old rubber without damaging the door, and which hidden nuances often overlooked when installing a new seal. The instructions are suitable for most models Pozis (including popular series RFN, DK, DA), but before starting work, be sure to check the technical documentation of your model - some fastening nuances may differ.

Signs that the seal needs to be replaced

It is not always obvious that the problem with the refrigerator is related specifically to the rubber band. Here are the key symptoms that indicate wear of the seal:

• 🔍 Visible damage: cracks, tears, deformation or separation of material from the door.
• ❄️ Ice on the back wall: if the refrigerator No Frost, but ice regularly forms on the back panel, this may indicate a leak warm air.
• 💰 Increasing electricity bills: a worn seal forces the compressor to work harder to maintain the set temperature.
• 🚪 The door does not close tightly: if there is a “kickback” when closing or the door itself opens when light tilting the refrigerator.
• 📏 Gaps between the elastic band and the body: check with a sheet of paper - if it is easily pulled out when the door is closed, the seal is not performing its function.

If you observe at least 2-3 signs of list, the probability of seal wear is 90%. Do not delay the replacement: constant suction of warm air can lead to thermostat breakdown or compressor overheating, and this is already a serious repair.

How to choose a seal for the refrigerator Pozis

Before purchasing a new seal, you need to accurately determine the model of your refrigerator Pozis. The model name is usually located on a sticker inside the camera (on the side) or on the back panel. For example, for the model Pozis RFN-125 a seal with article number RFN-125-UPLis suitable, and for Pozis DA-108 — DA-108-SEAL.

If the original seal could not be found, you can choose a universal analogue. The main selection criteria:

• 📏 Length and width: measure the old rubber around the perimeter of the door (taking into account the corners) and its width at the widest point.
• 🔄 Type of fastening: seals come in adhesive based, with groove for mounting plate or with self-tapping screws. U Pozis groove fastening is most often used.
• 🧲 Magnetic insert: high-quality The seals have a built-in magnetic tape for a tight fit. Check its availability.
• 🔍 Marking: original seals Pozis usually have a brand logo or article number that matches the refrigerator model.

If you are not sure of the choice, take the old rubber band with you to the store or take a photo of it from different angles. Consultants in specialized services (for example, Cold Master or RemBytTekhnika) will help you choose an analogue. Beware of cheap seals without a magnetic insert - they will last no more than a year.

Preparation for replacement: tools and safety measures

To replace the seal on the refrigerator Pozis you will need:

• 🔧 Phillips screwdriver (for models with self-tapping screws) or flat (for prying up the grooves).
• 🔨 Plastic spatula (to carefully remove the old rubber band).
• 🧴 Silicone sealant (if the seal is adhesive-based).
• 🧲 Hair dryer construction (for softening glue or plastic during dismantling).
• 🧼 Soap solution and a rag (for cleaning the surface).
• 📏 Tape measure (for measuring a new seal).

Before starting work be sure to unplug the refrigerator and get all the products. If there is ice in the freezer, let it melt (you can speed up the process by placing a container of hot water inside). It is more convenient to work if the door is removed - this will require an assistant, since the weight of the door can exceed 10–15 kg.

⚠️ Attention: If your refrigerator Pozis with a system No Frost, after replacing the seal, the fan noise may temporarily increase. This is normal - the system adapts to the new level of tightness. If the noise does not go away after 2-3 days, check if the seal is pinched somewhere.

Take a photo of the fastening of the old rubber band|Disconnect the refrigerator from the mains|Remove all food and defrost the chamber|Prepare tools and a new seal|Clean the door surface from dirt and grease-->

Step-by-step instructions: how to remove the old one seal

Removing the old rubber band is the most important step. If the groove or fastening on the door is damaged, the new seal may not hold. Proceed carefully:

1. Heat the corners of the seal with a hairdryer (temperature 50–60°C) - this will soften the glue or plastic and make removal easier.
2. Pry up the elastic with a spatula in one of the upper corners. Start from the corner, since the fastening there is usually less rigid.
3. Pull the seal toward you, gradually releasing it from the groove. If the rubber band is glued, use a solvent (for example, White spirit) to remove any remaining glue.
4. Clean the groove from dirt and glue. Wipe it with soapy water and dry it.

Some models Pozis (for example, Pozis RTA-320) the seal is attached with self-tapping screws under the decorative strip. In this case:

1. Remove the bar by prying it with a screwdriver.
2. Unscrew the screws (usually there are 4-6 of them).
3. Carefully remove the rubber band, remembering the location of the fasteners.

⚠️ Attention: If the groove on the door is cracked or deformed during dismantling, do not attempt to install a new seal over the damage. In this case, you will need to replace the door or repair it using epoxy resin (for plastic doors).

What to do if the seal is stuck to the door?

If the rubber does not budge even after heating with a hairdryer, try the following method:

1. Apply to the joint WD-40 or glue solvent.

2. Wait 10–15 minutes.

3. Carefully pry the seal with a blunt screwdriver, moving from the corner to the center.

Do not use a knife - it can scratch the door or damage the groove.

Installing a new seal: a step-by-step guide

The new seal is installed in the reverse order. The main rule: start from the upper corners of and move down, evenly distributing the elastic along the groove. For models Pozis with a groove fastening:

1. Pull the seal over the upper corners the door, making sure that it fits tightly into the groove.
2. Secure the sides, gradually pressing the elastic with your fingers. Do not pull it - this may deform the profile.
3. Fix the lower partstarting from the corners to the center. Here you can use a flat-head screwdriver to tuck the seal deeper.
4. Check the symmetry: the elastic should fit evenly around the entire perimeter, without waves or distortions.

For adhesive-based seals:

1. Apply a thin layer of silicone sealant to the door groove.
2. Apply an elastic band, starting from the top corner, and press it along the entire perimeter.
3. Secure the seal with masking tape for 12–24 hours (up to the glue has completely dried).

If the seal is attached with self-tapping screws (as in Pozis RTA-320):

1. Insert the elastic band into the groove and align the holes for the screws.
2. Tighten the screws without overtightening them (so as not to break the thread).
3. Replace the decorative strip.

Checking the tightness after replacement

Even if The seal is installed correctly, its effectiveness needs to be checked. Here are 3 diagnostic methods:

• 📄 Test with paper: close the door, holding a sheet of paper between the seal and the body. If the sheet is easily pulled out, the seal is broken.
• 💡 Visual inspection: turn on the flashlight and shine it along the door joint. in a dark room. If light is visible, there is a gap.
• 📏 Temperature measurement: place the thermometer in the refrigerator. If after 2-3 hours the temperature has not dropped to +4...+6°C, the seal is leaking air.

If tests show insufficient tightness:

• Check whether the rubber fits evenly around the entire perimeter.
• Make sure the door is not warped (adjust the hinges if necessary).
• If the seal is too hard, warm up it with a hairdryer (temperature 40–50°C) - this will make it more elastic.

⚠️ Attention: After replacing the seal, the refrigerator Pozis may become louder for 1-2 days. This is due to the fact that the compressor adapts to the new level of tightness. If the noise does not decrease after 48 hours. check to see if the seal is pinched somewhere or if debris has gotten under it.

Common mistakes and how to avoid them

Even with careful replacement of the seal, you can make mistakes that will negate all efforts. Here are the most common mistakes and ways to prevent them:

Another typical mistake is ignoring magnetic insert in the seal. If it is damaged or missing, the door will not close with the required force. Before purchasing, check whether there is a magnet in the new rubber band (bring a metal object to it). it should stick).

FAQ: answers to frequently asked questions

Is it possible to repair an old seal without buying a new one?

If the damage is minor (small cracks or peeling in one place), you can try to restore the gum:

• Fill the cracks with silicone sealant (after degreasing the surface).
• If the seal comes off in the corners, secure it superglue or double-sided tape.
• To restore elasticity, immerse the elastic band in hot water (60–70°C) for 10-15 minutes.

However, such measures are a temporary solution. If the seal is older than 5 years, it is better to replace it.

How much does it cost to replace the seal at the service center?

The cost of the service depends on the model of the refrigerator and the type of seal:

• Simple replacement (groove seal): 1,500–2,500 ₽.
• Complicated replacement (with door dismantling or adhesive fastening): 2,500–4,000 ₽.
• Replacing the seal on the freezer: +500–1,000 ₽ to the base price.

The cost of the seal itself is usually not included in the price of the work. make sure it is suitable for your model Pozis.

How often do you need to change the seal on the refrigerator?

The service life of the seal depends on the intensity of use of the refrigerator and care for it:

• With careful use: 5-7 years.
• With active use (frequent opening of the door, high humidity): 3–5 years.
• With no care (dirt, grease, mold on the elastic): 2–3 years.

Extend life the seal will be helped by regular cleaning with soapy water and treatment silicone grease (once every 6 months).

What to do if after replacing the seal the refrigerator began to freeze worse?

This may be due to several reasons:

1. Loose fit of the rubber band: check the tightness with a sheet of paper and adjust the seal.
2. Pressing of the tubes or cables: inspect the back wall of the refrigerator - perhaps the capillary tube was pinched when installing the door.
3. Thermostat malfunction: after replacing the seal, the temperature in the chamber may temporarily change. Give the refrigerator 12-24 hours to stabilize.
4. Compressor malfunction: if the problem does not disappear after a day, call a technician for diagnosis.

Is it possible to replace the seal only on the freezer compartment if the problem is there?

Yes, the seals on the refrigerator and freezer compartments are replaced independently of each other. However, please note:

• Freezer seals are usually thicker have a denser magnetic insert.
• In two-chamber models Pozis (for example, Pozis RTA-320) may require partial dismantling of the middle partition.
• After replacing the seal on the freezer, let it defrost and dry before turning it on.