Purchasing a new household appliance The delivery of a device is always a joyful event, but immediately after delivery the most important stage begins. Correct installation of the refrigerator Indesit determines not only its durability, but also the quality of food cooling, as well as the noise level during operation. Many users make a critical mistake by turning on the equipment to the network immediately after bringing it into the apartment, which can lead to compressor failure due to disruption of oil circulation.
The installation process requires careful attention to detail, starting with site preparation and ending with the final calibration of the housing position. The Italian brand Indesit is famous for its reliability, but these units, like any complex equipment, are sensitive to distortions and incorrect temperature conditions when first started. In this article, we will analyze in detail all the steps so that your new device serves faithfully for many years without unnecessary hum and excessive energy consumption.
Preparation of the room and selection of installation location
The first step is a thorough analysis of the room where the unit will be placed. The refrigerator Indesit must stand on a flat, stable floor, away from direct sunlight and heating devices. Thermal insulation walls and the proximity of heating radiators play a key role: if you place the equipment close to a hot radiator, the compressor will work hard, trying to compensate for the external temperature.
It is important to ensure free air circulation around the housing. The back wall of the device, where the capacitor is located, must be at a distance of at least 5-10 cm from the wall. Side clearances are also necessary, especially if the refrigerator is built into a niche in the kitchen unit. Lack of space leads to overheating and reduced cooling efficiency.
Pay attention to the flooring. Linoleum, tile or laminate flooring must be dry and clean. If the floor is slippery, there is a risk of heavy equipment moving due to vibration while the motor is running. In such cases, it is recommended to use special anti-slip pads under the supports.
⚠️ Attention: It is strictly forbidden to install the refrigerator in unheated rooms (for example, on a balcony or in a garage) if the technical documentation of the model Indesit does not indicate an extended climate class. Operation at temperatures below +10°C leads to oil thickening and compressor failure.
Check for a nearby electrical outlet. It must be grounded and have proper wiring capable of withstanding inrush currents. The use of extension cords and tees is highly undesirable, as this creates a risk of poor contact and fire.
Unpacking and removing shipping elements
After the box with the refrigerator Indesit has been delivered to the installation site, proceed with careful unpacking. Remove the cardboard packaging, tape and protective film. Inside, you'll find foam clips that hold the doors and interior shelves in place. All these elements must be completely removed before turning on.
Pay special attention to the shipping bolts if they are present in your model (they are more often found in washing machines, but in some large refrigerators they can fix the compressor). However, in most modern models Indesit the main task is to remove the tape that secures the doors and remove the protective film from the internal shelves and drawers.
☑️ Check after unpacking
Inside the chamber there may be instructions, warranty cards and egg trays. They must be removed so as not to be damaged when the door is closed for the first time. Also check the condition of the rubber seal around the perimeter of the doors - it should be clean and fit tightly to the body.
If you notice any external defects, dents or chips, they should be fixed in the presence of the delivery people. Mechanical damage can affect the tightness of the chamber and the efficiency of the refrigerant refrigerant.
Adjusting the supports and leveling the body
The most important technical stage is to level the refrigerator strictly. Incorrect installation will result in the door not closing tightly on its own and the compressor experiencing increased vibration. Refrigerators Indesit usually have two front adjustable legs and two rear ones (or the back panel rests on casters/fixed legs).
Use a building level to make adjustments. Attach it to the top panel of the refrigerator, first lengthwise, then crosswise. The air bubble should be strictly in the center. If the body is skewed, the door may open spontaneously or, conversely, require effort to close.
Adjustment is carried out by screwing or unscrewing the front legs. In some models Indesit this requires a key, in others you can use your hands or a flat-head screwdriver. By raising or lowering the angle, you change the tilt of the entire device.
| Symptom | Possible cause | Elimination method |
|---|---|---|
| The door opens itself | Tilting the body forward | Unscrew the front legs, lifting the front part |
| Strong vibration during operation | The refrigerator does not stand on all four supports | Adjust the height of the legs until they are in tight contact with the floor |
| Gap in seal at the bottom | Horizontal skew | Use a level and level the body |
| Difficult to close the door | Tilt back too much | Lower the front supports a little |
The correct position is when the refrigerator body Indesit has a barely noticeable tilt back (about 2 degrees). This ensures that the door closes naturally under its own weight, which ensures that the chamber remains sealed and cool inside.
Stopping time before first switching on
One of the most frequently asked questions: how long should the refrigerator sit for after transportation? The answer depends on the transport conditions and time of year. During the moving process, especially if the equipment was tilted, oil from the compressor could flow into the refrigerant circulation system.
If the refrigerator Indesit was transported in an upright position and it is warm outside, 2-3 hours of rest is enough. In winter or after horizontal transportation, the settling time increases to 4-6 hours, and in some cases - up to a day. This is necessary so that the oil flows back into the compressor crankcase and the refrigerant is distributed evenly.
What will happen if you turn on the refrigerator right away?
If you start the compressor with oil in the tubes, water hammer may occur. This will lead to breakdown of the compressor valves or blockage of the capillary tube, which will require expensive repairs.
Ignoring this rule is the most common reason for the failure of new units. A compressor, deprived of lubrication, operates “dry”, which sharply reduces its service life. Refrigerant in liquid form should also not enter the compression chamber.
While the device is settling, you can wash the internal shelves and drawers with warm water and a mild detergent. This will remove the smell of new plastic and dust that got in during assembly.
Connecting to the electrical network and first start-up
After the settling time has expired, you can proceed to the electrical connection. Make sure that the outlet matches the power parameters of the refrigerator Indesit (usually standard household 220-230V). The plug should fit tightly into the rosette, without play.
Plug in the device. The operation indicator on the control panel (or inside the camera, depending on the model) should light up or the light bulb should light up when the door is opened. Modern models with electronic control can emit a sound signal indicating an increase in temperature.
For the first hours of operation, the refrigerator will operate in enhanced mode, gaining the required temperature. Do not load the camera with food right away. Let the equipment run idle for at least 2-4 hours to stabilize the temperature in all compartments, including the zone Zero Zone, if provided for by the design.
⚠️ Attention: If, after turning on, you hear a loud knock, buzzing or see sparking in the plug area, immediately unplug the device. This may indicate a wiring fault or a compressor defect.
Check the heating of the side walls. In modern models Indesit the capacitor is often built into the side panels, so they can become noticeably hot (up to 50-60°C). This is a normal working process, not a defect.
Setting temperature modes and operation
When the refrigerator Indesit has been idle for several hours, you can start adjusting the temperature. For mechanical control, a rotary control inside the camera is used. Typically the scale goes from 1 to 5 or from Min to Max.
The optimal value for everyday use is the middle of the scale (position 2.5 or 3). This provides a balance between high-quality cooling and economical energy consumption. In winter you can slightly reduce the power, and in summer you can increase it.
Models with a system No Frost or electronic control allow you to set the exact temperature in degrees. The recommended range for the main compartment is +3°C to +5°C, and for the freezer compartment -18°C or lower. This temperature guarantees long-term storage of products and preservation of their beneficial properties.
Check the operation of the unit regularly. If you notice that the food in the back of the chamber is freezing, but the food at the door is getting warmer, you may need to adjust the position of the thermostat or check how tightly the door is closed.
Frequent questions during installation (FAQ)
Can the Indesit refrigerator be placed close to the wall?
No, minimal the gap between the back of the refrigerator and the wall should be at least 5-10 cm. This is necessary for free air circulation and heat removal from the condenser. If there is no gap, the equipment will overheat.
Why does the refrigerator hum after installation?
A slight hum from the compressor is normal. However, loud noise can be caused by the refrigerator not being level and vibrating when touching furniture or walls. Also check that the shipping bolts (if applicable) have not been removed and that the tubes are not touching each other.
Does a new refrigerator need to be defrosted before use?
There is no need to specifically defrost a new refrigerator if it has not been used. However, it is necessary to wash the internal shelves and drawers with warm water and soda or a mild detergent to remove factory dust and the smell of plastic.
What to do if the Indesit refrigerator door does not close tightly?
First of all, check whether something is preventing it from closing (food, packaging). Make sure the refrigerator is level and tilted slightly backwards. Check the cleanliness of the sealing rubber - dirt may impair the seal.
How to rehang the door to the other side?
Many models Indesit allow you to rehang the door. To do this, you will need to remove the door, move the hinges to the opposite side of the body and reinstall the handle. Detailed instructions with diagrams are always included in the kit, but it is better to entrust this procedure to professionals so as not to damage the hinges.