Buying a new household appliance is always a joyful event, especially when it comes to about reliable technology Indesit, which is famous for its durability. However, in order for the equipment to serve the period stated by the manufacturer and not fail in the first week, it is necessary to strictly follow the initial start-up rules. Many users make the mistake of believing that it is enough to simply plug the cord into an outlet, forgetting about the critical nuances of transportation and temperature acclimatization.
In this article we will look in detail at how to properly turn on the refrigerator Indesit after delivery, how long you need to wait before starting the compressor and how to set the temperature for first use. Ignoring these rules may result in compressor damage, refrigerant leakage, or system malfunction. NoFrost.
It is important to understand that the installation process is not just about placing appliances in the kitchen. This is a set of measures, including preparing the room, checking the condition of the unit and its correct electrical activation. If the refrigerator was transported lying down, the minimum standing time before turning it on is 4-6 hours, and in winter - up to 12 hours.
Primary preparation and installation of the case
Before thinking about turning it on network, it is necessary to correctly install the refrigerator body itself. Indesit, like any other equipment in this class, requires a perfectly flat and stable surface. If your kitchen floor is uneven, be sure to use the adjustable support feet located on the lower front of the unit. This will prevent vibration and excess noise when the compressor operates.
A critical parameter is maintaining clearances for ventilation. The back wall of the refrigerator should not fit tightly against the wall or furniture. Air must circulate freely around the condenser, otherwise the cooling system will be overloaded. The minimum distance to the rear wall should be at least 5-7 cm, and to the side walls - about 3-5 cm.
Make sure that the installation location is free of heat sources such as radiators, gas stoves or direct sunlight. Increased ambient temperature forces the compressor Indesit to work almost non-stop, which sharply reduces its resource. Also check that the doors open freely and do not touch the kitchen units.
After installing the cabinet, you must remove all shipping materials. This applies not only to the outer cardboard, but also to the internal fastenings, tape that secures shelves and drawers, as well as protective film on metal surfaces. If internal spacers are left in place, they may damage the drawer mechanism or interfere with the circulation of cold air inside the chambers.
Temperature adaptation after transportation
One of the most frequently asked questions concerns the waiting time before turning on. This parameter directly depends on the position and at what ambient temperature the transportation was carried out. If the refrigerator was transported vertically, the standing time can be minimal (2-3 hours) so that the pressure in the system stabilizes.
The situation changes dramatically if the unit was transported in a horizontal position. In this case, oil from the compressor could leak into the refrigerant circuit. If you turn on the device immediately, the compressor will pump oil, which will lead to water hammer and failure of the unit. The oil should completely drain back into the compressor crankcase.
⚠️ Attention: If you brought the refrigerator in from the cold (temperature below +10°C), do not plug it in immediately! Let it come to room temperature for 4-6 hours. A sudden start of a cold compressor can cause condensation on the electrical contacts and damage the insulation.
The table below shows the recommended holding times for refrigerators Indesit depending on delivery conditions:
| Transportation conditions | Environment temperature | Minimum settling time |
|---|---|---|
| Vertical position | Above +10°C | 2-3 hours |
| Horizontal position | Above +10°C | 4-6 hours |
| Any position | Below 0°C (winter) | 12-24 hours (before heating) |
| Severe shaking on the way | Any | 6-8 hours |
Checking the electrical network and grounding
Refrigerators Indesit are sensitive to the quality of the power supply. Before connecting, make sure that the socket is working properly and matches the load. The power of modern models is low, but the compressor starting currents can be significant. It is highly not recommended to use extension cords or tees, especially cheap ones, as poor contact can cause sparking and fire.
A mandatory requirement is the presence of grounding. Many older buildings do not have a ground loop, which can cause static electricity to build up on the building or create a potential that can be felt when touched. For the correct operation of electronics and the safety of users, the socket must be three-pin with a ground connection.
If your network experiences frequent power surges, it is strongly recommended to install a voltage stabilizer or at least a voltage control relay. The electronic control module Indesit can burn out during a sudden surge, and replacing the board is an expensive repair. It is also worth checking whether the plug or wire is overheating after the first hours of operation.
Some models with the system Full NoFrost install complex electronic units that require a stable current frequency. Using low quality generators or inverters may result in incorrect display readings or fan failure.
Algorithm for first switching on and setting
After all the preparatory stages have been completed, you can proceed to the actual switching on. The process is simple, but requires a sequence of steps. First, make sure all doors are tightly closed and the interior shelves are in place. An open door when first started will cause the compressor to run on empty, cooling your kitchen instead of the food.
Plug the power cord into the outlet. In models with electronic control, a characteristic sound signal is heard and an indication lights up on the display. If you have a mechanical model Indesit, you will hear a quiet click of the start relay and the hum of the motor starting. This is a normal operating situation.
☑️ Check before starting
Now you need to adjust the thermostat. Do not immediately turn the knob to the maximum (usually this is position 5 or 6). For the first launch, it is optimal to set the average value, for example 3 or 4. This will allow the compressor to reach operating mode without extreme loads. In electronic models, select the mode Smart or set the temperature to +4°C for the refrigerator compartment and -18°C for the freezer.
After turning on, let the refrigerator run idle for at least 2-3 hours. During this time, it must reach the required temperature. Only after stable cold has established inside can food be loaded. Loading warm food into a refrigerator that has not cooled down will cause the system to overload.
Monitoring and testing systems
In the first hours of operation, listen carefully to the sounds made by your Indesit. A quiet hum of the compressor, gurgling of the refrigerant in the tubes (especially in models with a weeping wall) and periodic turning on of the fans are allowed. However, loud knocking, clanging, or high-pitched whistling sounds are signs of a malfunction or improper installation.
Check the tightness of the door closure. To do this, you can conduct a simple test: hold a piece of paper with the refrigerator door. If the sheet can be pulled out without effort, it means that the seal does not fit tightly or the body is warped. In systems NoFrost this will lead to constant freezing and warm, humid air getting inside.
⚠️ Attention: If after 3-4 hours of operation the back wall of the refrigerator compartment (or the wall with a weeping effect) remains warm and the food is not cooled, there may be a freon leak or a compressor failure. In this case, operation should be stopped.
Pay attention to the side walls of the housing. In modern models Indesit capacitors are often built into the side panels, so they can heat up to 50-60°C. This is not a defect, but a normal mode of heat removal. However, if only one local point is heated or a burning smell is felt, immediately turn off the device.
Why does the refrigerator not turn off for a long time on the first day?
In the first 24 hours of operation, the refrigerator loads thermal inertia. It should cool not only the air, but also the plastic walls, shelves and drawers. Therefore, the first cycle of compressor operation can last up to 12 hours without interruption.
Frequent startup errors and their consequences
Many users ignore the instructions, which leads to a reduction in the service life of the equipment. One of the most common mistakes is loading a large amount of food at room temperature immediately after switching on. This creates a critical load on the compressor, which is trying to cool a large volume of heat.
Another mistake is installing the refrigerator close to the wall. Lack of ventilation means that hot air does not escape from the condenser, but circulates around the rear wall. The temperature in the motor area rises, cooling efficiency drops, and the refrigerator begins to work continuously, consuming more electricity.
Some try to speed up the cooling process by turning the thermostat to the maximum. In models Indesit this can lead to freezing of food in the refrigerator compartment and the formation of an ice crust that will take a long time to defrost. In addition, this does not speed up the build-up of cold, but only increases the operating time of the motor.
FAQ: Frequently asked questions
Is it possible to turn on the Indesit refrigerator immediately after delivery if it was carried vertically?
Yes, if the transportation did not last long and was carried out vertically, it is enough to let the device stand 1-2 hours to stabilize the pressure and acclimatize the electronics. However, if there are doubts about the transportation conditions, it is better to wait 3-4 hours.
Why does the refrigerator make a loud bang when turned on?
A single loud click at start is the operation of the start relay, this is normal. If the pops are repeated, accompanied by a hum, but the compressor does not start, or a metallic clang is heard, this is a sign of a malfunction of the starting device or jamming of the compressor.
Do you need to wash the refrigerator before turning it on for the first time?
Absolutely. The smell of plastic or factory dust may remain inside new appliances. Wipe the interior surfaces with a soft cloth soaked in a mild solution of baking soda or vinegar, and allow the cameras to dry before turning them on.
What should you do if the alarm indicator lights up after turning them on?
On models with a display, the alarm indicator (often a red exclamation mark or flashing symbol) will light up if the temperature inside the camera is higher than normal. This is normal the first time you turn it on. The indicator will go off when the refrigerator reaches the set temperature.