Defrosting the freezer of the Atlant refrigerator: instructions for all models

Defrosting the freezer is a procedure that many people put off until the last minute, until the ice begins to interfere with closing the door or takes up half the usable volume. Refrigerators Atlant, despite the reliability of the Belarusian manufacturer, require regular maintenance, especially if you have a model with manual defrosting or a hybrid system. In this article we will look at how to defrost a freezer Frost Free. In this article we will look at how to defrost a freezer. Atlant quickly, safely and without the risk of damaging equipment.

Modern models (for example, Atlant MHM 1708-80 or Atlant XM 6025-031) are equipped with different types of defrosting: from full manual to partially automatic. However, even systems No Frost require periodic “general cleaning” - removing ice from the seals and the rear wall. We will tell you how to act depending on type of yours freezerswhat tools will be useful, and why you can’t use a knife to chop ice.

Important: if you have never defrosted a refrigerator Atlant or have done it for a long time, prepare for the fact that the process can take from 4 to 12 hours. It all depends on the thickness of the ice layer, the room temperature and the chosen method. But there are ways to speed up defrosting - read about them in the corresponding section.

When it’s time to defrost the freezer: 5 signs

The manufacturer recommends defrosting refrigerators Atlant with a manual system at least once every 6-12 months. However, in practice, the frequency depends on the intensity of use, the humidity in the room and the tightness of the door. The following signs will help determine that it is time to start the procedure:

• 🔹 Ice is more than 5-7 mm thick on the walls or bottom of the freezer - this not only reduces the usable volume, but also causes the compressor to wear out, increasing energy consumption.
• 🔹 The door does not close well or requires effort - ice on the seal breaks the seal, causing the temperature inside the chamber to rise.
• 🔹 Constant noise of the compressor - if the refrigerator Atlant began to hum louder and rarely turns off, this may indicate an overload due to ice.
• 🔹 Unpleasant odor —old ice absorbs food odors, and when they thaw, they intensify.
• 🔹 Snow “coat” on food —if packages of food are covered with frost, this is a sign of impaired air circulation due to ice.

In models with No Frost (for example, Atlant XM 4626-100) ice Forms less frequently, but can still appear on the seal or in the drainage hole. If you notice at least 2-3 signs from the list, do not delay defrosting - this will extend the life of the equipment.

⚠️ Attention: In refrigerators Atlant with a system Frost Free (combined) the freezer requires manual defrost even if the main compartment defrosts automatically. Neglecting this procedure leads to fan failure or freezing of the evaporator.

Preparation for defrosting: what needs to be done in advance

Improper preparation can result in a flood in the kitchen, spoiled food or even a short circuit. To avoid problems, follow these steps to on how to unplug the refrigerator from the outlet:

1. Turn off the power. Unplug the plug from the outlet - you cannot defrost the refrigerator Atlant with the compressor on. In models with electronic control (for example Atlant MHM 2835-90), before turning off, set the temperature regulator to "0" or turn off the button Super Freeze.
2. Remove all products. Place them in a thermal bag, a pan with cold water, or wrap them in newspaper and place them in a cool place (for example, on a balcony in winter). Do not leave meat or fish at room temperature for more than 2 hours.
3. Remove shelves and drawers. Remove all removable elements (grids, containers, trays) and wash them with warm water and soda. This will get rid of bacteria and odors.
4. Prepare a place to collect water. Place a tray under the refrigerator or lay out towels. In models Atlant the drainage hole is located at the back - water will flow down the back wall.
5. Check the seal. If the rubber is deformed or cracked, after defrosting it will have to be replaced (article number for Atlant — 60.3601.102).

If your model has a function Vacation (vacation), activate it after defrosting - this will prevent the formation of ice during rare use.

Step-by-step instructions: how to defrost an Atlant freezer

The defrosting process depends on the type of system of your refrigerator Below are universal instructions suitable for most models Atlantincluding MHM 1840-80, XM 4026-000 and others. If you have No Frost, skip the steps associated with chipping ice - just wipe the walls.

Step 1: Natural defrosting (the safest method)

This is the standard method recommended by the manufacturer. It takes longer, but eliminates the risk of damaging the freezer.

1. Leave the door. freezer open after turning off the power.
2. Wait 6–12 hours (depending on the thickness of the ice). You can speed up the process by placing a pan of hot water inside (but not boiling water!).
3. Every 30–60 minutes, remove the melted water with a rag or sponge.
4. Do not try to peel off the ice with a knife or fork - this may puncture the evaporator.

Step 2: Accelerated defrosting (for a thick layer of ice)

If the ice has accumulated heavily (2-3 cm thick), and there is no time to wait half a day, use one of the proven methods:

• 💨 Hair dryer. Direct a stream of warm (not hot!) air at the ice build-ups, holding the hair dryer at a distance of 20–30 cm. Do not focus on one place for more than 2–3 minutes.
• 📰 Newspaper soaked in hot water. Put it on the ice - this will speed up the melting without risk to equipment.
• 🧊 Plastic scraper. You can carefully remove the top layer of ice, but without pressing.

In Atlant models with the Frost Free system, you should not point the hair dryer at the ventilation holes - this may damage the blowing system.

Step 3: Cleaning after defrosting

When the ice has completely melted:

1. Wipe the walls and shelves with a solution of water and vinegar (1:1) or soda (2 tablespoons per 1 liter of water).
2. Rinse the drainage hole (located at the back of the freezer) using a cotton swab or syringe with warm water.
3. Dry the chamber with a towel or leave the door open for 1-2 hours.
4. Plug in the refrigerator and wait until the temperature drops to −18°C before loading food.

How long does it take to defrost an Atlant freezer

The defrosting time depends on several factors: the type of refrigerator, the thickness of the ice layer and the chosen method. The table below shows approximate data for models Atlant:

Helps speed up the process high temperature in the room (for example, if defrosting in the summer) or using a fan directed into the freezer. However, do not place heaters closer than 1 meter to the refrigerator - this is dangerous!

⚠️ Attention: If after 12 hours of defrosting the ice remains in place, check if the drainage hole is clogged. In models Atlant it is located at the bottom of the back wall. freezers. A blockage can block the outflow of melt water, which is why the ice melts only from the top.

What should not be done when defrosting the Atlant refrigerator

Incorrect actions can lead to damage compressor, damage to the evaporator, or even a short circuit. Avoid these mistakes:

• ❌ Use sharp objects (knives, forks, screwdrivers) to chip the ice. This risks puncturing the freon pipes, which will lead to leakage and expensive repairs.
• ❌ Pour boiling water over the ice. Sharp temperature changes can deform the plastic or damage the seal.
• ❌ Turn on the refrigerator while it is running wet. Moisture on the electrical contacts (for example, in the control unit) will cause a short circuit.
• ❌ Place hot objects on shelves. Glass shelves in models Atlant (for example, MHM 2835-90) can crack due to temperature changes.
• ❌ Ignore the drainage hole. If it is not cleaned, water will accumulate at the bottom of the freezer and freeze again.

You need to be especially careful with models that have which drip defrosting system (for example, Atlant XM 4026-000). In them, the drainage hole often becomes clogged, which leads to the accumulation of water under the vegetable boxes.

What to do if the refrigerator does not turn on after defrosting?

If the refrigerator Atlant does not start after defrosting, check:

1. Is it connected to the outlet (sometimes a plug). falls out).

2. Has the circuit breaker on the panel tripped (during a short circuit).

3. Room temperature - if below +5°C, the compressor may not start (overload protection).

If this is not the problem, call a technician - it may have burned out start-protection relay or compressor.

How often do you need to defrost the Atlant freezer?

The frequency of defrosting depends on the type of system and operating conditions. Atlant gives the following recommendations:

• 🔄 Manual defrosting: every 6–12 months (or when the ice layer is more than 5 mm).
• ❄️ No Frost: once every 1-2 years (to clean the seal and ventilation holes).
• 🌬️ Frost Free: defrost the freezer once a year, the main department - as needed.

However, other factors also influence practice:

• 💧 Humidity in the room. If the kitchen is damp or soup is often prepared, ice forms faster.
• 🚪 Frequency of door opening. Every time you look into the freezer, warm water gets inside air that condenses into ice.
• 🔌 Voltage drops. If the voltage in the network often fluctuates, the compressor operates unstably, which accelerates freezing.

To defrost less often refrigerator Atlant, follow these simple tips:

• 📦 Store food in airtight containers or bags - this reduces moisture evaporation.
• 🧊 Do not put hot or warm foods in the freezer - let them cool to room temperature.
• 🔧 Check the seal regularly - if it is worn out, replace it (cost for Atlant - from 800 rubles).

Features of defrosting for different Atlant models

Refrigerators Atlant are produced with different defrosting systems, which affects on the process. Below are the key differences for popular series:

On models. c electronic control (for example, Atlant MHM 2835-90) after defrosting, an alarm may sound. To reset it, press and hold the button Alarm Reset (or OK) for 3 seconds.

⚠️ Attention: In refrigerators Atlant with a display after defrosting, an error may be displayed E1 or E2. This means that the temperature sensor does not work correctly temporarily. The error will disappear within 1-2 hours after switching on.

FAQ: Frequently asked questions about defrosting Atlant refrigerators

Is it possible to defrost an Atlant refrigerator without unplugging it?

No, this is dangerous! Defrosting while the power is on leads to overheating of the compressor and the risk of a short circuit. The exception is models with the function Super Cool, but it is better to turn them off.

Why does ice quickly appear again in the Atlant freezer after defrosting?

The reasons may be the following:

• Faulty thermostat (does not regulate the temperature correctly).
• Clogged drainage channel —water does not drain, but freezes.
• Worn out seal —warm air penetrates inside.
• Frequently opening the door or storing loosely packaged products.

Check these points and, if necessary, call a specialist.

How to defrost an Atlant freezer if the ice has not melted for a day?

Most likely, the problem is clogged drain hole or system malfunction defrosting (in models with No FrostTry:

1. Clean the hole with a wire or a syringe.
2. Check whether the fan is working (in models with Frost Free).
3. If it doesn’t help, contact the service center (freon leakage is possible).

Is it necessary to defrost a new Atlant refrigerator before turning on for the first time?

Yes, but only if it was stored or transported at sub-zero temperatures. In this case, let it sit at room temperature for 2-4 hours, then wipe it with a dry cloth and turn it on. If the refrigerator was bought in a warm store, defrosting is not required.

Can salt or special products be used to speed up defrosting?

Salt is not recommended - it can damage metal and plastic parts. It is better to use: Warm water in bowls (place on shelves). into the freezer (at minimum speed).

• Warm water in bowls (place on shelves).
• Special defrosters for refrigerators (eg Top House).
• Fan directed towards the freezer (at minimum speed).

Do not use chemicals with abrasives!