Refrigeration units of the series Atlant 6025 are deservedly popular due to their reliability and classic two-chamber design, however, even the highest quality equipment requires periodic maintenance. Sooner or later, every owner is faced with the need to carry out complete defrostingto remove ice and ensure efficient operation of the compressor. Ignoring this procedure can lead to increased energy consumption and a decrease in the quality of freezing products.
The defrosting process does not require complex technical skills, but requires adherence to a strict sequence of actions so as not to damage the fragile elements of the cooling system. Unlike modern models with the No Frost function, classic Atlanta need manual intervention approximately once every six months or as an ice crust forms. The correct approach will extend the service life refrigeration circuit and preserve the freshness of products.
In this article we will analyze in detail each stage of preparation, the immediate process of thawing and subsequent startup of the equipment. You will learn why you should not use sharp objects to chip ice and how to quickly return the unit to operating mode. Compliance with these simple rules will ensure that your refrigerator will work silently and efficiently for many years.
Preparation for the procedure for turning off the unit
Before starting any manipulations with the power supply, you must empty the chambers of their contents. Products should be removed from refrigeration and freezer compartments, sorting them: what needs to be defrosted can be eaten, and frozen supplies should be temporarily transferred to another cold place or covered with a blanket in a cool room. This is especially true in winter, when you can take advantage of natural cold.
It is important to prepare a container for collecting water in advance, since the volume of melting ice can be significant. The model Atlant 6025 is characterized by the presence of a lower location of the freezer compartment, so water will flow there and then through the drainage hole (if it is not clogged) or simply overflow onto the floor. Protection of the floor covering is a critical stage that is often missed.
- 🧹 Lay old towels or absorbent rags around the unit in advance.
- 🥣 Prepare wide basins or baking sheets for installation under the freezer.
- 🧽 Prepare a soft sponge and a neutral detergent for subsequent cleaning.
- 🔌 Find an accessible outlet so you don't have to pull an extension cord across the entire kitchen.
⚠️ Attention: Do not try to speed up the defrosting process by leaving doors open in a draft or using a hair dryer aimed at the seals. A sharp temperature change can deform rubber cuffswhich will lead to loose fitting of the doors in the future.
Correct shutdown and removal of components
After the products are removed and The place is prepared, you can proceed to turn off the power supply. Unplug the cord from the outlet - this is the only safe way to disconnect the power compressor before servicing. It is not recommended to simply turn off the device with the button on the case, if there is one, since the current must be completely excluded from the circuit.
Next, you need to remove all removable interior elements. The model Atlant 6025 has glass shelves, plastic trays for vegetables, containers on the door and, of course, a grill in the freezer. Plastic becomes fragile in the cold, so remove the shelves carefully, without sudden movements, so as not to break guides or the shelves themselves.
All removed parts should be taken to the bathroom or outside for washing. You cannot wash them with hot water directly inside the chamber, since a sharp temperature contrast is dangerous for the internal coating. Leave the refrigerator doors wide open to allow air circulation and speed up the natural melting of ice.
☑️ Ready to defrost
Natural thawing and accelerating the process
The safest method of removing ice is waiting. The ice will begin to melt on its own when exposed to room temperature. Depending on the thickness of the crust and the room temperature, the process can take from 3 to 10 hours. Atlant 6025 with its useful volume is characterized by the formation of a significant amount of condensate.
If time is running out, you can carefully speed up the process, but without fanaticism. It is allowed to use bowls with warm (not hot!) water, which can be placed on the bottom of the chambers or on the shelves. The steam rising from the water will gently act on the ice formations, softening their structure.
Under no circumstances use sharp objects - knives, screwdrivers or chisels - to chip ice. The inner surface of the chambers is covered with a thin layer of enamel or special plastic, under which there are channels evaporator. One awkward movement can break through the wall, which will lead to a refrigerant leak and expensive repairs, which are often not economically feasible.
Can a hair dryer be used for defrosting?
The use of a hair dryer is permissible only in extreme cases and with great care. The stream of warm air must be directed strictly at the ice, avoiding contact with plastic parts of doors and seals, which can melt or become deformed from spot overheating. Keep the hairdryer at least 30 cm from the surface of the ice.
Cleaning, washing and disinfecting chambers
When all the ice has melted and the water has been removed, the general cleaning stage begins. Even if the chamber appears clean visually, bacteria and mold may have settled on the walls, causing an unpleasant odor. Use a weak solution of baking soda or a special refrigerator cleaner.
Wipe all surfaces thoroughly, paying special attention to corners and joints where dirt most often accumulates. Pay special attention sealing rubber bands to the doors: it is in their folds that black mold most often hides. Wipe them with a cotton pad soaked in a solution of vinegar or hydrogen peroxide.
After wet cleaning, be sure to wipe all surfaces dry with a clean cloth. The remaining moisture will turn into a new layer of frost when turned on, negating all defrosting efforts. Let the chambers dry completely, leaving the doors open for another 15–20 minutes.
| Element | What to wash | Processing features |
|---|---|---|
| Internal walls | Soda solution (1 tbsp per 1 liter of water) | Do not use abrasives |
| Seals | Vinegar solution or peroxide | Wipe each fold |
| Glass shelves | Warm water with detergent | First warm to room temperature |
| Plastic trays | Soap solution | Rinse thoroughly to remove foam |
Starting the refrigerator after defrosting
After the unit has been washed and dried, you can put it back together. Replace all shelves, drawers and containers. Make sure that they fit tightly and evenly so as not to damage the products during further use. Now you can connect the device to the network.
Do not rush to load products immediately after switching on. Atlant refrigerator It takes time to reach operating temperature in the chambers and stabilize the pressure in the system. Usually this process takes from 2 to 4 hours, depending on the ambient temperature.
During the first hours of operation, listen to the sounds of the motor. Periodic clicking of the thermal relay and the noise of the operating compressor are allowed. However, if you hear a loud knocking, grinding or humming noise that wasn't there before, this may indicate a problem. In normal mode Atlant 6025 it works quite quietly.
Typical maintenance errors
Many users make mistakes that negate the benefits of defrosting or even harm the equipment. One of the most common is turning on the device with wet walls. This leads to the instantaneous formation of a new ice crust and overload of the system.
Another mistake is the use of aggressive chemistry. Chlorine-containing products or solvents can corrode the plastic and ruin the color of the interior surfaces. In addition, chemical residues can be absorbed into food, which is hazardous to health.
⚠️ Attention: Never turn on the refrigerator if you notice mechanical damage to the case or wiring. First, fix the problem or contact a service center.
It is also worth remembering about regular maintenance. Waiting until the ice completely blocks the freezer door will put extra stress on the engine. Try to carry out the procedure as planned, without waiting for a critical condition.
Frequently asked questions (FAQ)
How long should the Atlant 6025 refrigerator stand before turning it on after defrosting?
After defrosting and washing the chambers is completed, it is enough to let the device stand with the doors open for 20-30 minutes for final drying and ventilation. Immediately after this, you can turn it on to the network. There is no need to wait several hours before turning it on after washing, unlike the situation after transportation.
Is it possible to defrost the Atlant refrigerator without unplugging it from the outlet?
No, this is strictly prohibited by electrical safety rules. Defrosting is only possible when the power supply is completely turned off. Operating the compressor during defrosting will lead to its overheating and rapid failure, as it will try to compensate for the heat from the melting ice.
What to do if the refrigerator does not freeze after defrosting?
If more than 5-6 hours have passed after turning it on and the cold has not appeared, check whether the doors are tightly closed. If the seal is OK, the circuit may have been damaged during defrosting or the thermostat may have failed. In this case, diagnostics by a specialist is necessary.
Is it necessary to lubricate the seals after defrosting?
Yes, this is a useful procedure. After washing and drying the rubber seals, it is recommended to wipe them with silicone grease or glycerin. This will preserve the elasticity of the rubber, prevent it from drying out and cracking, ensuring a tight fit to the door.