Owners of Belarusian brand equipment are often faced with the need for scheduled maintenance, which includes defrosting the chambers. The model range Atlant is famous for its reliability, but even the most advanced units require periodic removal of accumulated moisture. Ignoring this process can lead to the formation of ice jams, deterioration in the quality of food storage and the appearance of an unpleasant odor in the kitchen space.
The procedure for removing condensate and melt water requires care, especially if your model does not have an automatic evaporation system or it is out of order. It is important to understand that correct defrosting extends the life of the compressor and seals. In this article we will analyze in detail the algorithm of actions for various modifications, including systems No Frost and drip refrigerators.
Before taking active steps, you need to prepare the workplace and empty the chambers of the contents. Completely turning off the power supply is a mandatory first safety step before any manipulations with water inside the cabinet. Let's look at what tools are needed and how to organize the process is as efficient as possible so as not to flood the kitchen.
⚠️ Attention: Before starting work, make sure that the floor around the refrigerator is covered with absorbent fabric, as even a small leak can damage the laminate or linoleum.
Preparation for the defrosting and moisture removal procedure
The initial stage requires careful preparation, on which the speed and cleanliness of the work depends. You will need to empty both chambers of food, remove all shelves, drawers and lattice elements. This is necessary not only for access to the internal walls, but also to prevent food spoilage when the temperature inside the unit rises.
After removing the removable elements, they should be washed with warm water and a mild detergent and left to dry. At this time, you can start preparing a container for collecting water. Models Atlant with a bottom freezer often require a tray with high sides, since the volume of melting ice can be significant.
Be sure to check the condition of the rubber seals on the doors. If they have cracks or do not fit tightly, the defrosting process will be faster, but in normal operation this will lead to the constant formation of ice. Circuit tightness is a key factor in the stable operation of refrigeration equipment.
Instructions for models with a drip defrosting system
Refrigerators Atlantequipped with a drip system in the refrigerator compartment require a special approach to draining water. In such models, moisture flows down the back wall into a special gutter and leaves through the drainage hole. Over time, this channel can become clogged with food particles or mold, which leads to the accumulation of water at the bottom of the chamber.
To clean the drainage, use a soft wire coated with insulation or a special brush-brush. Carefully insert the tool into the hole located at the bottom of the back wall, making rotational movements. This will help break through the formed plug and restore the normal outflow of condensate.
If the water is in the gutter and does not go away, you can use a medical bulb or a syringe without a needle. Take warm water and squirt it under pressure into the drainage hole. This method is effective for washing out greasy deposits, which often cause blockages in the drainage system.
☑️ Cleaning the drip system
Features of draining water in No Frost refrigerators
The system No Frost assumes automatic evaporation of moisture, but in some cases forced defrosting is required. This may be caused by a malfunction of the defrost heating element, a clogged drain tube, or simply routine maintenance cleaning. In such models, water accumulates in a special tray above the compressor, from where it must evaporate.
If you notice water on the floor under the refrigerator or inside the chamber, the drainage system is most likely clogged. To access it in models Atlant often you need to remove the back panel in the freezer compartment. Be careful with plastic latches; they can become brittle after prolonged exposure to low temperatures.
After removing the panel, inspect the drainage hole. Often this is where an ice plug forms, blocking the flow of melt water into the evaporator. To eliminate it, you can use a hairdryer by directing a warm stream of air at the hole, but without overheating the plastic. Drainage channel Must be absolutely free for normal circulation of air and moisture.
Why is there water in No Frost?
Water in refrigerators with a system No Frost most often appears due to a clogged drain tube or a malfunction of the defrost sensor. The ice does not have time to melt and blocks the path of air, which is why moisture begins to accumulate inside the chamber and flow out.
Using available means to speed up the process
Natural defrosting of the refrigerator Atlant can take from 6 to 12 hours, which is not always convenient. To speed up the process, you can use safe methods that will not damage the internal coating of the cameras. The main rule is not to use sharp objects to chip ice, as this can lead to depressurization of the circuit.
One of the effective ways is to install containers with hot water on shelves. The steam rising from the water will gently warm the ice formations, accelerating their melting. The doors should be tightly closed to create the effect of a steam bath inside the chamber.
You can also use a fan to direct a flow of air at room temperature inside the open refrigerator. This will increase circulation and help dry the internal surfaces faster after the bulk of the ice has melted. Temperature conditions At the same time, it should remain gentle.
| Acceleration method | Exposure time | Efficiency | Risks |
|---|---|---|---|
| Natural defrosting | 8-12 hours | High | Minimum |
| Hot water containers | 2-4 hours | Medium | Possible damage to shelves |
| Hair dryer (warm air) | 30-60 minutes | High | Plastic overheating |
| Fan | 3-5 hours | Medium | Blowing dust |
Removing blockages in the drainage system
Clogged drainage is the most common reason why water does not drain away, but flows out. In the system Atlant the drainage tube can become clogged not only with ice, but also with food debris, crumbs or mucus. For high-quality cleaning, it is recommended to use a solution of baking soda or citric acid.
Prepare a warm solution and pour it into the drainage hole using a syringe or bulb. Let the liquid sit for a few minutes to dissolve the fatty deposits, and then blow out the canal. If the water flows freely and a characteristic gurgling sound is heard in the tray above the compressor, then the system is clean.
In difficult cases, when simple flushing does not help, it may be necessary to dismantle the rear panel of the freezer to access the inside of the tube. This is a more complex procedure that requires care when working with fasteners and plastic interior parts.
⚠️ Attention: Never pour boiling water directly onto the plastic case or shelves of the refrigerator, as a sudden temperature change can cause deformation or cracks of the plastic.
Final stage: drying and starting
After all the ice has melted and the water has been removed, you must thoroughly wipe everything dry surfaces. Use a soft, lint-free cloth. Pay special attention to the corners of the chamber and the place where the drainage hole exits, where moisture could remain.
Leave the refrigerator doors Atlant open for another 30-60 minutes to completely evaporate residual moisture and eliminate the smell. Only after this can you install shelves, drawers and load products. It is recommended to connect the device to the network no earlier than 2 hours after the end of defrosting.
The first start-up is best done without load, allowing the compressor to reach operating mode within 1-2 hours. This will help stabilize the temperature regime and make sure there are no leaks. Check inspection one day after startup will ensure the correct operation of the drainage system.
Is it possible to use a knife to remove ice in the Atlant refrigerator?
It is strictly not recommended to use sharp metal objects, such as knives or chisels, to chip ice. Mechanical damage to the internal circuit or evaporator will result in refrigerant leakage and costly repairs. Use only plastic scrapers or natural defrosting methods.
How often should you drain the water and defrost the refrigerator?
The frequency of defrosting depends on the model. For drip-type systems, it is recommended to carry out the procedure 1-2 times a year. Refrigerators with the system No Frost require defrosting only in case of malfunction or scheduled maintenance once every 1-2 years, unless the instructions indicate otherwise.
What to do if after defrosting water still flows to the floor?
If after thoroughly cleaning the drainage, water continues to flow out, check the levelness refrigerator installations. If the body is tilted forward, water may not flow into the drain hole. Also, the cause may be a crack in the condensate tray itself or a displacement of the drain tube.
Do you need to wash the inside of the refrigerator after draining the water?
Yes, after defrosting it is necessary to wash the internal chambers with warm water and a mild detergent. This will remove bacteria and residual contaminants that may have accumulated during use. After washing the surface, wipe it dry with a clean cloth.