How to properly remove the door from a Pozis refrigerator: video + detailed instructions

Removing the refrigerator door Pozis is a task faced when moving, repairing or replacing a seal. It would seem that what is so difficult here? But incorrect actions can lead to damage to the hinges, depressurization of the chamber, or even breakdown of the compressor. In this article we will figure out how to dismantle the door without risk for equipment, what tools are needed and what to look for in models Pozis of different series.

The peculiarity of refrigerators of this brand is unified fastening system, but with nuances in depending on the year of manufacture. For example, models before 2019 often used metal hinges with open hinges, while new ones often used plastic clips under decorative plugs. We will look at both options in detail, and also provide links to official videos from the manufacturer (if available) and alternative sources.

Before you begin, please note: in 90% of cases, to remove the door you do not need to disconnect the refrigerator from the mains, but if you plan long-term storage without a door (more than 2 hours), it is better to turn off the compressor to avoid overheating. This is true for models with a system No Frost, where the fans continue to work even when the chamber is open.

Preparation for dismantling: tools and measures safety

Before removing the door, prepare your work space. The refrigerator must be placed on a level surface - even a slight tilt can cause the door to move and damage the hinges. If the floor is uneven, place sheets of plywood or rubber pads under the legs.

You will need:

• ✅ Phillips screwdriver (PH2) - for most models Pozis after 2015.
• ✅ Hex key (4 mm) - for older models with metal hinges.
• ✅ Plastic spatula or pick - to pry up the decorative plugs.
• ✅ Masking tape - to fix the door in the open position (required!).
• ✅ Gloves - hinges may be sharp edges.

⚠️ Attention: If your refrigerator Pozis is equipped with a display on the door (series Premium or Smart), turn off the power before removing! Otherwise, electronics may fail due to broken contacts.

Also prepare a place for storing the door. It is heavier than it looks: the weight can reach 15–20 kg depending on the model. Place a soft cloth or cardboard on the floor to avoid scratching the surface.

Step-by-step instructions: removing the door from the Pozis refrigerator

The dismantling process depends on the type of hinges. Below we will look at the two most common options. If your model is different, check the markings on the sticker inside the chamber (for example, Pozis RK-105W) and check the compatibility table.

Option 1: Plastic hinges with plugs (models after 2019)

This type of fastening is used in most modern refrigerators Pozis. The main advantage is that there is no need to completely unscrew the hinges.

1. Secure the door in the open position with masking tape so that it does not close spontaneously.
2. Remove the decorative plugs on the top and bottom hinges. Pry them off with a plastic spatula, starting from the corner.
3. Unscrew the screws under the plugs (usually 2-3 pieces on each loop). Some models use latches instead of screws - they need to be carefully bent.
4. Lift the door up and remove from the bottom pin. If the door is “jammed,” slightly swing it left and right.

If the door is equipped with display, before removing, disconnect the power cable (usually it is located under the top hinge). To do this:

1. Unscrew the lid of the box with wires.
2. Carefully pull out the connector (do not pull the wires!).
3. Fix the cable with tape to the refrigerator body so as not to damage contacts.

Option 2: Metal hinges (models before 2019)

In old refrigerators Pozis metal hinges were often installed hinges with open hinge. Here the process is more complicated, since it requires complete dismantling of the fastenings

1. Unscrew the screwsthat secure the upper and lower hinges to the refrigerator body (usually 3-4 screws for each).
2. Remove the hinges from the door and body. In some models, the lower hinge may be welded - in this case, it is enough to unscrew only the upper one.
3. Carefully remove the doorholding it by the lower edge. Metal hinges often “stick”, so WD-40 may be required.

⚠️ Attention: In models Pozis RK-140 i RK-160 the lower hinge has a hidden screw under rubber gasket. If you do not unscrew it, the door will not be removed!

After dismantling, inspect the hinges for corrosion or deformation. If they are damaged, replace them before reinstalling.

What to do if the screws are stuck?

If the screws do not come out, apply WD-40 or an equivalent to them and wait 10-15 minutes. Do not use excessive force as this may strip the threads. As a last resort, use an impact screwdriver or contact a specialist.

Video instructions: where to find and what to look for

Visual guidance greatly simplifies the process. Official videos from Pozis can be found on them YouTube channel (search by refrigerator model). However, not all models are covered - in this case, a universal video on dismantling the doors of refrigerators with a bottom freezer will help (relevant for most Pozis).

When watching the video, pay attention to:

• 🔧 Type of hinges (plastic/metal) - it should match your model.
• 🔌 Presence of electronics on the door - if the video shows a refrigerator without a display, and you have one, the process will be different.
• 📏 The procedure for removing the plugs - in some models they are fixed with latches, not screws.

If you could not find a video specifically for your model, use general instructions, but check with photographs of the hinges of your refrigerator. For example, in models Pozis RK-101 and RK-103 the hinges are visually similar, but differ in the location of the screws.

If you are not confident in your abilities, we recommend watching the video first end, and then repeat the actions. Pay attention to the moments where the presenter pauses - usually these are the most critical stages.

Common mistakes and how to avoid them

Even with instructions, many make mistakes that lead to breakdowns. Here are the most common of them:

• 🔨 Using inappropriate tools —for example, a flat-head screwdriver instead of a Phillips screwdriver. This breaks the screw slots.
• 🚪 Attempting to remove the door without fixing it —if it closes during dismantling, the seal or hinges can be damaged.
• ⚡ Ignoring electronics —in models with a display they forget disconnect the cable, which leads to a break in the wires.
• 🔩 Loss of screws or plugs —without them, reinstalling the door will be impossible.

Another typical problem is distortion of the door when reinstalling. This happens if the loops are not tightened evenly. To avoid this, tighten the screws diagonally: first the top left, then the bottom right, then the remaining ones.

⚠️ Attention: In refrigerators Pozis with the system No Frost after removing the door, an alarm may sound due to a leak. This is normal - the sound will disappear after reinstallation.

If after dismantling you notice that the door seal is damaged or has lost elasticity, replace it before reinstallation. Otherwise, the refrigerator will work with increased load, which will lead to increased energy consumption.

Reinstalling the door: nuances and adjustment

Reinstalling the door back is often more difficult than removing it. The main rule is Do not tighten the hinge screws completely right away. First, tighten all the fasteners, then check how the door fits on the pins. Only after this can you tighten the screws.

Procedure:

1. Place the door on the lower pin, lifting it at an angle of 10-15°.
2. Lower the door so that so that the top pin fits into the hinge.
3. Tighten the screws not all the way (70–80%).
4. Check how the door closes. It should fit evenly around the entire perimeter.
5. If there is misalignment, loosen the screws and adjust the position.
6. Tighten the screws completely and install decorative plugs.

To check the tightness, use sheet test paper:

1. Insert a sheet between the seal and the body.
2. Close the door and try to pull out the sheet.
3. If the sheet comes out easily, the seal requires adjustment or replacement.

In models with a display, do not forget to connect the cable back. Check the functionality of the buttons and indicators before final fixing the hinges.

When is it better to contact a specialist

Not all situations can be solved on your own. Contact a professional if:

• 🔧 The hinge screws are broken and cannot be unscrewed.
• ⚡ After removing the door, the refrigerator stopped turning on (there may be problems with the electronics).
• 🚪 The door is deformed or has cracks.
• 🔌 Damage to the display cable was detected.

The cost of the door removal/installation service at service centers Pozis ranges from 1,500 to 3,000 rubles, depending on the region and complexity of the work. If the refrigerator is under warranty, do not try to repair it yourself - this may void the warranty.

You will also need a technician if you plan reversing the door to the other side. In this case, it is necessary to reconfigure the hinges and, possibly, reinstall some parts (for example, the drainage system in models with No Frost).

⚠️ Attention: In some models Pozis (for example, RK-167) reversing the door requires replacing the seal with a mirror one. Check this in the instructions or with the manufacturer.

FAQ: Frequently asked questions about removing the Pozis refrigerator door

Do you need to unplug the refrigerator before removing the door?

In most cases, no, but if your model is equipped with a display or an electronic unit on the door, turning off is mandatory. We also recommend turning off the refrigerator if you plan to store it for a long time without a door (more than 2 hours) to avoid overheating of the compressor.

Is it possible to remove the door from a Pozis refrigerator alone?

Technically, yes, but it is inconvenient and dangerous. The door weighs 15-20 kg, and without an assistant it is easy to drop it. If there is no assistant, use safety nets. straps or place a soft stand under the door.

What should you do if, after installing the door, the refrigerator begins to operate loudly?

This is a sign that the door is not installed correctly and the seal is broken. The compressor is working with increased load, trying to compensate for the loss of cold. Immediately check the seal and adjust the hinges.

Where can I buy replacement hinges for my Pozis refrigerator?

Original spare parts are sold in service centers Pozis or on the official website. You can also find analogues on AliExpress, Yandex Market or in spare parts stores for household appliances (for example, 220 Volt). When purchasing, please specify the refrigerator model!

How long does it take to remove and install the door?

On average - from 30 minutes to 1.5 hours, in depending on experience and the type of hinges. The first time may take longer, especially if the screws are stuck or the seal needs to be replaced.