Removing refrigerator doors Atlant is a task faced when moving, repairing or replacing a seal. In two-chamber models with an upper or lower freezer, the process has nuances depending on the design of the hinge mechanism. Incorrect actions can lead to damage to the fasteners, warping of the door, or even breakdown of the compressor due to a leak. This article will help you figure out how remove the Atlant refrigerator door without risk, using a standard set of tools.
We will look at universal steps for popular series - MHM-1705, MXM-2835, MX-2824 and similar ones, and also point out the key differences in models with electronic control. We will pay special attention fixing the door removalto avoid falling and damage to the case. If your refrigerator was manufactured after 2018, check for the presence of additional plastic plugs on the hinges - their design may have changed.
Preparation for dismantling: tools and safety measures
Before starting work, make sure that the refrigerator unplugged at least 10 minutes beforehand - this will eliminate the risk of a short circuit due to accidental contact with wires (for example, in models with a display on the door). Prepare:
- 🔧 Phillips and flat-head screwdrivers (size for hinge fastening - usually
PH2orPZ2) - 📏 Building level or ruler (to check horizontality after installation)
- 🧲 Magnet or container for fastening (hinge screws are easily lost)
- 🧤 Cotton gloves (protection from sharp edges of the metal case)
If the refrigerator door Atlant equipped decorative overlays (for example, in series New Style or Premium), you will have to carefully pry them off with a flat screwdriver, starting from the bottom corner. In models 2020–2023, the overlays can be attached with latches - do not pull them by force, otherwise you will break the plastic. For doors with a display (series Smart), you will additionally need to disconnect the power cable - we will talk about this separately.
⚠️ Attention: Do not remove the door alone if its weight exceeds 15 kg (typical for models with a chamber volume >250 l). Ask an assistant to support the door leaf when unscrewing the last screw.
Step 1: Removing the top hinge (for models with a top freezer)
In refrigerators Atlant with a top freezer (MHM-1705, MHM-2808 etc.) is first removed top hinge. Algorithm of actions:
- Open the door freezer compartment at 90° and fix it in this position (for example, by placing a book).
- Remove the decorative hinge cover by prying it up with a flat blade screwdriver. In some models, the cover is attached to two latches - press them at the same time.
- Unscrew the two screws holding the hinge (usually they are hidden). under the cover). In models before 2019, the screws may be hexagon - prepare a key
4 mm. - Holding the door, carefully slide it up to remove the hinge pin from the groove.
If the door is “jammed” and cannot be moved, check that it is not in the way. sometimes it sticks to the body - slightly pull the door towards you while lifting it. In models with sealing. rubber. Sometimes it sticks to the body - slightly pull the door towards you while lifting it. In models with NoFrost system (for example MXM-2835-90), the hinge may have an additional lock - you need to press it out with a screwdriver.
☑️ Preparation for removing the top hinge
Step 2: Removing the lower hinge (common for all models)
The bottom hinge in refrigerators Atlant is attached to the body with two or three screws, which are often hidden under with a plastic plugTo remove it:
- Pry the plug on the side flat. a screwdriver (in models after 2020 it can be attached with Velcro - pull up).
- Unscrew the screws holding the hinge. In refrigerators with mechanical control (for example MX-2824-66) the screws can be a Phillips screwdriver, in electronic ones (MXM-2808-97) - for hexagon.
- Lift the door 1–2 cm and pull it yourself to remove the pin from the groove. If the door “does not give in,” check whether the screw on the back of the case has gone unnoticed.
In models with bottom freezer (MHM-1845, MHM-2848) the lower hinge may have adjusting bolt - it does not need to be unscrewed completely, it is enough to loosen it by 2-3 turns. After removing the door, the bolt is used for alignment when reinstalling.
| Refrigerator model | Hinge type | Number of screws | Features |
|---|---|---|---|
| MHM-1705 | Upper | 2 | Decorative cover with latches |
| MXM-2835-90 | Bottom | 3 | Adjusting bolt for leveling |
| MX-2824-66 | Upper/lower | 2 | Phillips screws |
| MXM-2808-97 (Smart) | Top | 2 + power cable | It is necessary to disconnect the display connector |
⚠️ Attention: In refrigerators with electronic display on the door, be sure to disconnect the cable before removing nutrition. It is located under the top hinge and is secured with a plastic clip. Do not pull the wires - only the connector!
Step 3: Features of models with electronic control
Refrigerators Atlant series Smart i New Style equipped with a display on the door, which is connected to the main control unit via a flexible cable. When dismantling the door, you must:
- Remove the decorative display panel by prying it off with a flat-head screwdriver (usually it is secured with 2-4 latches).
- Disconnect the cable from the connector on the refrigerator body. The connector can be fixed with a plastic clip - gently press it up.
- Insulate the exposed contacts of the cable with tape to avoid short circuits during further manipulations.
In models with touch control (for example, MXM-2808-97) The cable may be glued to the door - do not tear it off by force. Heat the attachment point with a hairdryer (temperature no higher than 50°C) to loosen the glue.
What to do if the cable is torn?
If the display cable is damaged during dismantling, the refrigerator will remain operational, but the screen will stop functioning. The cable can only be replaced at a service center - its article number is indicated in the product passport (section "Electrical diagram").
Step 4: Removing the door with a bottom freezer
In refrigerators with a bottom freezer (MHM-1845, MHM-2848) first is removed top door (refrigerator compartment), then the lower one (freezer compartment). Features of the process:
- 🔹 The top door is attached to two hinges: the top (with a decorative cover) and the middle (hidden under seal).
- 🔹 The middle hinge often has
adjusting screw- it needs to be loosened, but not completely unscrewed. - 🔹 The bottom door of the freezer is removed after dismantling the top one - it is attached on one hinge with a reinforced pin.
When removing the bottom door, be careful: its weight can reach 20 kg due to the thickened insulation layer. It is recommended to place a soft cloth (such as a towel) under it to avoid scratching the floor. In models with Frost Free system there may be an additional heating element on the freezer door - do not pull its wires.
Step 5: Storage and transportation of removed doors
After dismantling the doors, you need to properly prepare them for storage or transportation:
- 📦 Wrap the door leaf with bubble wrap or soft cloth so that avoid scratches.
- 🔄 Lay the door vertically (do not lay it flat - this will deform the seal).
- 🔧 Place screws and small parts in a bag and label (for example, “Top hinge MXM-2835").
- 🧲 If you removed the door with the display, secure the cable with tape to the canvas so that it does not dangle.
When transporting in a car, secure the door with belts so that it does not move. If you transport the refrigerator disassembled, the doors should move separately from the body - this will prevent damage to the hinges due to shaking. In models with glass shelves on the door (MHM-2808), first remove the shelves and pack them separately.
Typical mistakes and how to avoid them
Even with careful dismantling, mistakes can be made that will lead to breakdown. Let's look at the most common ones:
- 🔧 Unscrewing the screws in the wrong order: first loosen the top loop, then the bottom one. If you do the opposite, the door may fall.
- 🔌 Damage to the display cable: you cannot pull the wires - only the connector. In models Smart the cable is often glued, it needs to be carefully pryed off.
- 🚪 Strong pressure on seal: if the door “does not work”, do not pull it by force - check if all the screws are unscrewed.
- 🔩 Loss of screws or plugs: the hinge fastener often has a non-standard size, and it is difficult to find a replacement.
Another common problem is the door is skewed after reinstallation. This happens if the hinges are not adjusted to the level. Refrigerators Atlant have adjusting bolts for this purpose (usually marked in red or blue). Check the tightness after installation: place a sheet of paper between the seal and the body - if it falls out, the door needs to be tightened.
⚠️ Attention: If after removing the door you notice that The sealing rubber is cracked or deformedit needs to be replaced. Otherwise, the refrigerator will work under increased load, which will shorten the service life of the compressor.
FAQ: Frequently asked questions about removing the Atlant refrigerator doors
Is it possible to remove the Atlant refrigerator door alone?
For models with a volume of up to 200 l (for example, MHM-1705) this is possible, but risky - the door weighs 10–12 kg, and it is difficult to hold it with one hand when unscrewing the last screw. For refrigerators with a volume of >250 l (MXM-2835, MHM-2848), an assistant is definitely needed.
What what to do if the hinge screws are too tight and won't come out?
Use a screwdriver with an extended blade or add a lever (for example, a wrench to the handle). If the screw gets stuck, apply a few drops WD-40 and wait 5-10 minutes. Do not use excessive force - a broken thread will require replacement of the hinge.
How to remove a door if it is blocked by the “90° Opening” system?
Some models Atlant have an opening limiter. To turn it off, locate the plastic tab on the top hinge and slide it to the “OFF” position. After this, the door will open 180°, and it can be removed.
Is it necessary to remove the door handle before dismantling?
In most models (MHM-1705, MX-2824), the handle is secured with latches and does not interfere with removal. The exception is models with built-in rail handle (for example, MXM-2808-97), where it can block access to the hinge screws. In this case, the handle must be removed by prying it off with a flat blade screwdriver.
Is it possible to remove the door without unplugging the refrigerator?
Absolutely not. Even if you do not touch the electrical components, when removing the display door (Smart), there is a risk of a short circuit due to accidental contact with the wires. Turn off the refrigerator 10–15 minutes before starting work.