How to properly remove the shelf clamps in the Biryusa refrigerator: instructions with photos and tips

Removing the shelf clamps in the refrigerator Biryusa is a task encountered when rearranging shelves, general cleaning or repairs. It would seem, what could be simpler? But careless actions often lead to broken fasteners, scratches on the inner walls, or even damage to the door seal. In this article, we will analyze all types of fastenersused in models Biryusa (from classic Biryusa-18 to modern Biryusa-220), we will show how to dismantle them without tools and with minimal risk, and we will also tell you what to do if the mount is jammed or broken.

Features of refrigerators of this brand — combined fastening system: in some models the shelves are fixed with plastic latches, in others - with metal pins with rubber tips. In addition, in two-compartment refrigerators (for example Biryusa-130), the freezer compartment latches may differ from those in the main compartment. We have collected unique dismantling schemes for each type fasteningsincluding rare cases when the manufacturer used non-standard solutions (for example, in export versions for countries with hot climates).

Types of fasteners in Biryusa refrigerators: how to distinguish them

Before proceeding with dismantling, determine what type of fastenings are used in your model. This will save time and prevent damage. In refrigerators Biryusa there are 4 main types of fasteners:

• 🔹 Plastic latches —the most common option in models after 2010 (for example, Biryusa-150, Biryusa-185). They can be easily removed by hand, but require care when reinstalling.
• 🔹 Metal pins with rubber tips —typical for older models (Biryusa-6, Biryusa-8) and some two-compartment refrigerators. Can be removed with pliers or a screwdriver.
• 🔹 Combined fastenings (plastic + metal) - used in premium series (Biryusa Premium) for increased reliability. Dismantling requires a step-by-step approach.
• 🔹 Hidden fasteners —found in models with the system No Frost (for example, Biryusa-220 NF). The fastenings are hidden under decorative overlays and require preliminary removal of the panels.

To accurately identify the type, inspect the side walls of the refrigerator at the place where the shelf is attached. Plastic latches usually have protruding “ears”, and metal pins - round or square heads. In some models (for example, Biryusa-130K), the latches can be painted in the color of the body - they are more difficult to notice, but they are always located symmetrically on both sides.

Preparing for dismantling: tools and precautions

Even if you plan to remove the fasteners without tools, prepare in advance. These are preventable errors, such as fall of the shelf (especially dangerous for glass shelves) or damage to the door seal. Here's what you'll need:

• 🧤 Rubber gloves —protect your hands from sharp edges and prevent the shelf from sliding.
• 🔦 Flashlight —lighting will help you see the fasteners in the depths of the refrigerator.
• 📏 Ruler or caliper —useful if you need to measure the diameter of the pins for replacement.
• 🛠️ Flat a screwdriver or a plastic spatula —for prying up plastic latches.
• 🧲 Magnet - will help hold the metal pins if they fall out.

Before starting work be sure to unplug the refrigerator and wait until the temperature inside is equal to room temperature. This will prevent condensation from forming on glass shelves and reduce the risk of cracking. If there is food in the refrigerator, temporarily transfer it to a cooler bag or wrap it in towels.

⚠️ Attention: In models Biryusa with the system No Frost (for example, Biryusa-220 NF), removing the clamps may disrupt the operation of the ventilation. After removing the shelves, check whether the air ducts are blocked.

Step-by-step instructions: how to remove plastic clips

Plastic latches are the most common type of fasteners in modern refrigerators Biryusa. Their main advantage is possibility of dismantling without tools. However, many users make the mistake of trying to pull the shelf out by force. This leads to breakage of the latches or deformation of the grooves. Correct algorithm:

1. Free the shelf from products and pull it out to the maximum possible distance.

2. Holding the shelf with one hand, press the other plastic tongue of the latch (usually it is located on the side or bottom). In models Biryusa-150 i Biryusa-185 the tongue can be hidden under a small cover - pry it off with a fingernail or a plastic card.

3. Gently pull the shelf towards you while holding the tongue pressed. The movement should be smooth, without jerking.

4. Repeat the action for the latch on the other side. If the shelf cannot be removed, check whether the third latch has gone unnoticed (in some models it is located in the center of the back wall).

In refrigerators Biryusa s height-adjustable shelves (for example, Biryusa-220) the latch may have additional grooves to change the level. In this case, before dismantling, set the shelf to the extreme upper or lower position - this will facilitate access to the latches.

Release the shelf from products|Press the plastic tab|Smoothly pull the shelf toward you|Check for hidden fasteners-->

Removing metal pins: difficulties and solutions

Metal retainers are found in older models Turkish (before 2010) and some two-chamber refrigerators. Their main problem is corrosion and “sticking” to the grooves. If the pin cannot be removed manually, do not try to pull it out by force: this may damage the interior lining of the refrigerator. Instead:

1. Treat the attachment point silicone grease or WD-40. Wait 5-10 minutes for the composition to take effect.

2. If the pin protrudes above the surface, carefully grab it with pliers and rotate counterclockwise. In most models Turk the thread is left-handed, so standard unscrewing (to the right) may not work.

3. For deep-set pins, use magnetic holder or wrap the tip of the pin with electrical tape to improve adhesion to the tool.

4. If the pin breaks inside the groove, drill it with a drill with a thin drill bit (⌀ 2-3 mm), then remove the remains with tweezers.

In models Biryusa-6 i Biryusa-8 metal pins may be welded to the shelf frame. In this case, dismantling without damage is impossible - you will have to replace the entire shelf. Before purchasing a new shelf, check its article number: for Biryusa this is usually a type code RSh-XX, where XX is the model number.

⚠️ Attention: In refrigerators Turk with metal pins it is often used rubber gasket between the pin and groove. When dismantling, do not lose it - without a gasket, the new shelf will rattle when the compressor operates.

What to do if the pin is rusted and not does it give in?

If the pin is very rusty, try the following:

1. Apply a mixture of vinegar and soda (1:1) to the attachment point and leave for 15–20 minutes.

2. Use heating hair dryer (not higher than 60°C) to expand the metal.

3. If all else fails, carefully cut the pin with a hacksaw, leaving 1-2 mm for gripping with tweezers.

Hidden fasteners in models with No Frost: how to find and remove them

Refrigerators Biryusa with the system No Frost (for example, Biryusa-220 NF, Biryusa-185 NF) have complicated fastening system. The fasteners here are often hidden under decorative panels or integrated into the air ducts. To dismantle them:

1. Remove protective pad on the back wall of the refrigerator. It is attached to plastic clips - pry it off with a flathead screwdriver.

2. Under the pad you will see plastic or metal guidesthat hold the shelf. In models Turquoise NF they can be painted black for camouflage.

3. Click on latch on the side (usually it is marked arrow) and pull the shelf up. In some cases, you will need to first lift the shelf and then push it forward.

4. If the latch is locked, check whether it is in the way ventilation grille. In Biryusa-220 NF the grille is attached to two latches - they need to be released simultaneously.

Features of the systems No Frost — presence of temperature sensors on shelves. When dismantling, do not pull the wires or touch the sensors with your hands: this may cause the refrigerator to malfunction. If, after installing the shelves in place, the refrigerator begins to freeze worse, check whether the sensor has moved.

Common mistakes and how to avoid them

Even experienced users sometimes make mistakes when dismantling fasteners. Here are the most common of them and ways to prevent them:

• 🔧 Forcefully pulling out the shelf — leads to broken latches or cracks in the glass. Always check that all the latches are pressed out.
• 🔨 Using metal tools for plastic fasteners - leaves scratches. Use a plastic spatula or wooden spatula.
• 🧊 Dismantling while the refrigerator is running —condensation on the shelves can cause them to crack. Always turn off the power 1-2 hours before work.
• 🔄 Incorrect installation of shelves back —if the latches do not snap into place, the shelf will wobble. Check the reliability of fastening after installation.
• 🔍 Ignoring hidden fasteners —some models have additional latches in the center. They are easy to miss.

If after dismantling you find that the latch is broken, do not try to repair it with improvised means (adhesive tape, glue). In refrigerators Biryusa fastenings are subject to constant loads from compressor vibration, so temporary repairs will quickly fail. Original fasteners can be ordered from the manufacturer or purchased at service centers. Their article numbers are usually indicated in the instruction manual.

What to do if the latch is broken or jammed

If the latch is broken or jammed, do not panic. In most cases, the problem can be solved without calling a technician. Here is the algorithm of actions:

1. If the plastic latch is crackedbut holds the shelf, temporarily fix it a drop of superglue (for example, Loctite 401). This will allow you to use the refrigerator until the part is replaced.

2. If the metal pin is jammed, try loosening it with pliers in different directions. Lightly tapping a hammer through a wooden spacer often helps.

3. If the retainer has fallen inside the walldo not try to reach it with your hands - you risk damaging the insulation. Use tweezers with a magnetic tip or a flexible endoscope.

4. If the shelf is not fixed after reinstallation, check whether the grooves are deformed. In some cases, it helps to place a thin rubber gasket under the fastener To replace broken fasteners in refrigerators.

To replace broken fasteners in refrigerators Biryusa parts from other models of the same generation are suitable. For example, fasteners from Biryusa-150 are compatible with Biryusa-185, and fasteners from Biryusa-220 are compatible with Biryusa-220 NF. The main thing is that pin diameter and distance between grooves.

⚠️ Attention: If during dismantling you damaged internal lining the refrigerator, do not use sealant or mounting hardware to repair foam. These materials may release harmful substances when in contact with food. Contact the service center for professional repairs.

FAQ: answers to frequently asked questions

Is it possible to remove the shelves in the Biryusa refrigerator without disconnecting from the network?

Technically it is possible, but highly not recommended. Vibration from a running compressor can cause the shelf to slip and break. In addition, in models with No Frost removing shelves while the power is on can damage the automatic defrosting system.

Why did the refrigerator become louder after removing the shelves?

Most likely, you violated position ventilation grill or temperature sensor. In refrigerators Biryusa NF these elements are attached to the shelves. Check their location and adjust if necessary.

How to find out the model of your Biryusa refrigerator if the sticker has worn off?

The model is indicated on metal sign the back of the refrigerator (usually at the bottom left). If there is no sign, pay attention to:

• 🔹 Number of cameras (one- or two-chamber).
• 🔹 Availability of the system No Frost (if there are ventilation holes).
• 🔹 Color and shape of handles (in old models the handles are black, in new ones - chrome).

With this data, you can select compatible fasteners at the service center.

Is it possible to replace a glass shelf with a plastic one?

Technically yes, but not recommended. Plastic shelves in refrigerators Turk are designed for a lighter load (up to 5 kg versus 15 kg for glass ones). If you still want to replace, choose shelves with reinforced stiffeners and check the compatibility of the fasteners.

What what to do if after removing the shelves there is a smell in the refrigerator?

The smell may appear due to:

• 🔹 Mold under the shelves (wipe the walls with a 1:1 vinegar solution).
• 🔹 Dust in the ventilation ducts (in models with No Frost).
• 🔹 Damage to the seal (check the rubber gasket on the door).

If the smell does not disappear, use odor absorber (for example, activated carbon) or leave refrigerator open for 12–24 hours.