How to properly remove and replace a light bulb in a Hotpoint-Ariston refrigerator: instructions with photos and expert advice

Replacing a lamp in a refrigerator Hotpoint-Ariston is a task that sooner or later every owner of this brand of equipment faces. Even in reliable models, such as HBM 1821 or HFF 9202, the lighting element burns out, flickers or dims over time. But don’t rush to call a technician: the replacement procedure takes 10–15 minutes and does not require professional skills. The main thing is to know the exact sequence of actionsthe type of lamp in your model and basic precautions.

In this article we will look at how to remove a light bulb from a refrigerator Hotpoint-Ariston different series (including popular ones Fresh, Active and Total No Frost), what tools will be needed, and what to look for when choosing a new lamp. You will also find out why in some models after 2020, the lamp may be integrated into the ceiling and require a complete replacement of the module. If your refrigerator is equipped with LED lighting, there is a separate section for you with the nuances of dismantling.

1. Preparation: what you need to know before replacing a light bulb

Before starting work, determine lamp type in your refrigerator. The models Hotpoint-Ariston use three options:

• 💡 Incandescent lamps (power 15–25 W) - installed in older series until 2015. They have a standard base E14 or E27.
• 🔆 Halogen lamps (10–20 W) - found in models 2016–2019. Base G4 or G9, less often E14.
• 💡 LED lamps —modern refrigerators (from 2020) are equipped with LED modules, which can be removable or soldered into the lampshade.

To avoid making a mistake with your choice, check:

1. Markings on the lampshade (usually the power and type of base are indicated).
2. Instructions for the refrigerator (section "Technical specifications" or "Replacing the lamp").
3. A sticker on the back wall - the lamp code may be indicated there (for example, 230V E14 25W).

⚠️ Attention: In refrigerators Hotpoint-Ariston with a system Total No Frost (for example HBN 1372), the lamp can be connected to the control board. If dismantled incorrectly, there is a risk of damaging the contacts or causing an error E04 (lighting malfunction).

Also prepare the tools:

• 🔧 Screwdriver Phillips (for the ceiling screws).
• 🔧 Flat screwdriver (for prying up the latches).
• 🧤 Gloves (will protect against cuts and grease on the bulb).
• 📸 Phone (to photograph the location of the wires).

2. Hotpoint-Ariston

The dismantling process depends on design of the ceilingLet's consider two options: classic (with screws) and modern (with latches).

Option 1: Ceiling lamp with screws (models up to 2018)

1. Disconnect the refrigerator from the mains. Just remove the plug from the socket - this will protect you from electric shock.
2. Remove all products from the top shelf (if the lampshade is located there).
3. Carefully unscrew screws holding the lampshade. Usually there are 2-3 of them (on the sides or bottom).
4. Remove the lampshade and place it on a flat surface face up.
5. Unscrew the light bulb counterclockwise (for the base E14/E27) or pull towards you (for G4/G9).

Option 2: Lamp with snaps (models after 2018)

1. Turn off the power and release the shelf.
2. Insert a flat-head screwdriver into the groove between the lamp and the ceiling refrigerator.
3. Carefully pry up the lampshade on one side, then on the other - it should come out of the grooves.
4. Disconnect the power connector (if the lamp is LED and connected via a plug).
5. For halogen lamps: press the bulb up and turn counterclockwise. For LED: remove. module from the grooves.

If the lamp is stuck or does not unscrew:

• 🔧 Wear rubber gloves for better grip.
• 🔧 Use pliers, wrapping the lips with electrical tape (so as not to damage the base).
• 🔧 Apply a little WD-40 to the thread and wait 5 minutes.

3. Features of replacing LED lamps in refrigerators Hotpoint-Ariston

Since 2020 Hotpoint-Ariston has been actively switching to LED backlighting. Unlike incandescent lamps, LED modules can be:

• 🔆 Removable — the lamp is inserted into the connector on the lampshade (for example, in models HFC 3952).
• 🔆 Soldered in —LED elements are integrated into the lampshade, and if they burn out, the entire module needs to be replaced (relevant for HBN 1821 and the newest series).

For removable LED lamps:

1. Disconnect the power connector from the lampshade (usually a white plug with 2-3 contacts).
2. Remove the lamp from the grooves by pulling towards you.
3. Install a new lamp, aligning the contacts with the connector.

If the LED module is soldered in:

• The entire lampshade will need to be replaced. It can be ordered using the part code (indicated on the sticker on the back).
• The cost of the original lampshade for Hotpoint-Ariston is from 1,500 to 3,000 rubles (for 2026).
• When installing a new lamp, check that the wires are not twisted and do not touch the body.

⚠️ Attention: In refrigerators with electronic control (display on the door), after replacing the LED lamp, you may need to reset the error. To do this, press and hold the button. Super Cool 5 seconds.

How to check the functionality of a new LED lamp before installation?

Connect the lamp to a 12V or 24V power source (depending on the model) using the power supply. If it does not light up, check the polarity or integrity of the contacts.

4. Choosing a new lamp: what parameters are important

Not all lamps are suitable for refrigerators Hotpoint-Ariston. When choosing a replacement, consider:

Where to buy a lamp for Hotpoint-Ariston:

• 🛒 Official service centers (guaranteed compatibility).
• 🛒 Stores of spare parts for household appliances (for example, 220-volt, All-Zap).
• 🛒 Online platforms (Wildberries, Ozon) - search by the code of the original lamp.

For LED lamps, pay attention to:

• 🔆 Connector type (for example, JST 2.0 or Molex).
• 🔆 Polarity - to The lampshade is usually marked “+” and “−”.
• 🔆 Brightness —optimally 150–300 lumens (too bright lamp is blinding).

5. Common mistakes and how to avoid them

Even with the apparent simplicity of the procedure, refrigerator owners Hotpoint-Ariston often make mistakes that lead to repeated replacement or breakdowns. common:

• ⚡ Replacement without turning off the power —risk of electric shock or short circuit. Always remove the plug from the socket!
• 🔧 Using force when unscrewing —may break the base or damage the socket If the lamp does not work, use WD-40.
• 💡 Using higher power lamps —leads to melting of the lampshade (especially in models with a plastic body).
• 🔌 Incorrect connection of the LED lamp —reversed polarity or weak contact causes flickering.
• 🧊 Replacement when the cooling mode is on —condensation on the lampshade can cause corrosion of the contacts.

How to check that the lamp is installed correctly:

1. Close the door and turn on refrigerator.
2. Open the door - the light should come on immediately, without delay.
3. Look at the lampshade: there should be no crackling, burning smell or flickering.

⚠️ Attention: If after replacing the lamp does not light, check:

• 🔌 Correct connection of the connector (for LED).
• 🔧 Integrity of the fuse on the board (in models with a display).
• 💡 Serviceability of the lamp itself (check with a multimeter).

6. Replacing the lamp in Hotpoint-Ariston refrigerators with a display

In models with electronic control (for example, HFC 3952 or HBN 1821) the process of replacing the lamp has nuances:

1. Before starting work take a photo connecting wires to the lampshade - this will help avoid errors during assembly.
2. In some models, the lampshade is connected to the control board via 3-pin connector. Disconnect it carefully by pulling the body, not the wires.
3. After replacing the lamp, an error may appear E04 (lighting fault). To reset it, press and hold the button Super Freeze 10 seconds.

If after replacement the display shows an error or the refrigerator does not turn on:

• 🔧 Check if the wires are damaged during dismantling.
• 🔌 Make sure the connectors are connected tightly (sometimes a slight rocking of the plug helps).
• 📞 Contact a service technician center, if the error does not reset, the control board may be damaged.

In refrigerators with a touch screen (for example, HFF 9202), the lamp may be connected to the door opening sensor. If after replacement the light does not turn on when opened, check:

• 🔆 The functionality of the sensor (usually located next to lamp).
• 🔆 Lighting settings in the menu (in some models the brightness is adjustable).

7. When to contact a specialist

In most cases, you can replace the light bulb in the refrigerator yourself. However, there are situations when it is better to call. specialist: Hotpoint-Ariston you can do it yourself. However, there are situations when it is better to call a specialist:

• 🔌 If, when replacing the lamp, you saw melted wires or smelled burning, this is a sign of a short circuit.
• 💡 If the lamp is new flickers or does not light, and all connections are checked - the problem may be in the power supply of the LED module.
• 🛠️ If the lamp is cracked or deformed - the entire module will need to be replaced, which is difficult to do without experience.
• 📉 If the refrigerator stopped cooling after replacing the lamp, the temperature sensor may be affected.

Cost of replacing the lamp in the service center:

• 💰 Incandescent/halogen lamp: 500–1,000 rubles (with work).
• 💰 LED module: 1,500–3,000 rubles (depending on the model).
• 💰 Replacement of the lampshade: 2 000–4,000 rubles.

If you decide to contact a specialist, prepare:

• 📄 Refrigerator model (indicated on the sticker inside or on the back).
• 💡 Lamp type (if known).
• 📋 Description of the problem (flickers, does not light, crackles, etc.).

⚠️ Attention: In refrigerators Hotpoint-Ariston with a guarantee, replacing the lamp yourself may void the warranty. If the equipment is under warranty, contact an authorized service center.

FAQ: Frequently asked questions about replacing the lamp in a Hotpoint-Ariston refrigerator

Is it possible to replace an incandescent lamp with an LED in an old refrigerator?

Yes, but you need to consider:

• 🔆 The LED lamp must have the same base (E14 or E27).
• 🔆 The power of the LED lamp should not exceed the original one (for example, instead of 25 W, take a 3-5 W LED).
• 🔆 For some models, an adapter will be required, since LED lamps may flicker due to low voltage in the circuit refrigerator.

Why does a new lamp burn out quickly?

The reasons may be as follows:

• ⚡ Voltage surges in the network - install a stabilizer.
• 🔌 Poor contact in the socket - check and clean contacts.
• 💡 Poor quality lamp - buy proven brands (Osram, Philips).
• 🌡️ Overheating of the lampshade - make sure that the lamp is not covered with food or packaging.

How to remove the lampshade if the screws are rusty?

Proceed carefully as follows:

1. Apply detergent WD-40 or vinegar to the screws, wait 10 minutes.
2. Use a screwdriver with a magnetic tip to prevent the screws from falling inside the case.
3. If the screw does not come out, try carefully drilling it with a drill (minimum drill diameter).

After dismantling, replace the rusty screws with new ones (furniture screws of the same size will do).

What to do if the lamp breaks inside the lampshade?

Follow the instructions:

1. Turn off the refrigerator and let the lamp cool for 10 minutes.
2. Wear gloves and goggles to avoid cuts.
3. Use pliers to carefully remove the remaining base, turning it counterclockwise arrows.
4. If the base is stuck, use a wine stopper: insert it into the socket and unscrew it.
5. Check the socket for glass fragments.

Where can I find an original lamp for my model?

Options search:

• 🛒 Official website Hotpoint-Ariston —enter the refrigerator model in the search for spare parts.
• 🛒 Service centers - they often have original parts even for older models.
• 🛒 Groups on social networks (for example, “Spare parts” for refrigerators") - they sell used parts from disassembly.
• 🛒 Stores like 220-volt or All-Zap - search by lamp code (for example, C00356789).

If If you can’t find the original, take an analogue with identical parameters (base, power, voltage).