How to carefully remove the shade from the light bulb in the refrigerator: instructions for 10 popular brands

Removing the shade from a light bulb in the refrigerator seems like a simple task - until you come across latches that break with an awkward movement, or you discover that the fastening in your model Samsung RB37J5240 is radically different from Indesit BIAA 13. In 80% of cases, the problem lies not in the light bulb itself, but in the oxidized contacts of the lampshade or a cracked diffuser, which begins to let moisture through. But before you run to the service center, figure out how to properly dismantle the lighting unit - this will save up to 1,500 rubles on a technician’s visit.

In this article you will find step-by-step instructions for refrigerators with top, bottom and side lightingan analysis of the nuances of fastenings (from rotary clamps to hidden screws), as well as a unique table of compatibility of lampshades and lamps for 20+ models. Particular attention was paid to typical mistakes: why you can’t pull the lampshade “towards you” in models LG with magnetic holders and how not to damage the thermostat when dismantling it Atlanta.

Preparation: tools and safety measures

Before you climb inside the refrigerator, make sure you have at hand:

• 🔧 Flat screwdriver (tip width 3–5 mm) - for prying up the latches. Do not take a Phillips head: it will crumble the plastic.
• 🧲 Magnetic holder or tweezers - so as not to drop the screws into the drainage hole.
• 💡 Spare bulb (if you are planning a replacement). Suitable for modern models LED T5 12V 3W, for old ones - incandescent E14 15W.
• 🧻 Microfiber cloth - wipe the contacts from oxidation (use alcohol, not water!).

Critical error - ignore power off. Even if the light is not on, voltage can be supplied to the lamp contacts through the control module. In refrigerators Bosch Serie 6 i Siemens iQ500 the lighting circuit is connected to the door sensor: if dismantled carelessly, you can burn the controller (repair will cost 5-7 thousand rubles). Always remove the plug from sockets!

⚠️ Attention: In refrigerators with a system No Frost (for example, Liebherr CNef 4315) the lampshade is often attached to the air duct. If you break the fasteners, the air circulation will be disrupted - you will have to defrost the chamber and check the fan.

Types of lampshade fastenings: how to determine yours

Manufacturers use 5 main types of lampshade fixation. You can determine the type by external characteristics:

If your model is not included in the table, inspect the ceiling for:

• 🔍 The gaps between the body and the lamp shade —if a gap of 1–2 mm is visible, a latch is hidden there.
• 🔍 Symmetrical protrusions —they need to be pressed simultaneously (for example, in Electrolux ERN 1200 FOW).
• 🔍 The inscriptions “PUSH” or “TURN”** —indicate rotary mechanism.

Step-by-step instructions for refrigerators with latches

This type of fastening is the most common - it is used in 60% of budget models (Indesit, Beko, Pozytron). Algorithm of actions:

1. Turn off the refrigerator and wait until the light bulb cools down (if it was on in models with LED-backlit). immediately.
2. Find the latches —they are located on the sides of the ceiling. In Beko RCSK 250M00 S there are two of them, in Pozytron PR-145 there are four (in the corners).
3. Pry up the latches with a screwdriver, pressing them one by one. Do not try to squeeze both at once - the plastic will crack!
4. Lower the lampshade down by 1-2 cm, then pull it towards you (Vestfrost VF 3920) it will only be removed at an angle. 45°.

Typical problem: the latch is broken and the lampshade is hanging. In this case:

⚠️ Attention: Do not use superglue for repairs! The next time you dismantle the lampshade, you will have to break it. It is better to order the original latch (article number). for Indesit — C00284301, cost ~200 rubles).

De-energize the refrigerator|Prepare a screwdriver and a napkin|Check the type of fastening|Take a photo of the original position-->

Features of dismantling in refrigerators with screw fastening

Screws are found in models of the middle and premium segment (Samsung, Gorenje, Sharp). It would seem that what could go wrong? In practice, users encounter:

• 🔩 Rusted screws - especially in refrigerators older than 5 years (for example, Sharp SJ-FX630V-SL).
• 🔩 Hidden screws under the decorative trim (as in Samsung RB-37 J5240).
• 🔩 Screws with a non-standard head (for example, Torx T8 in Gorenje RK 60359).

Instructions for screw fastening:

1. If the screw does not unscrew, drip on it WD-40 or kerosene. Wait 10 minutes.
2. In models Samsung remove the decorative trim first - it is attached to clips. Pry it off with a screwdriver at the top edge.
3. For screws Torx use the appropriate bit. Do not try to select the size by eye - you will tear off the slots.
4. After removing the lampshade, check sealing rubber on the back side. hardened, replace it (article for Gorenje — 48103001000).

In refrigerators Sharp with a system J-Tech Inverter the lampshade is often attached to the evaporator cover. When dismantling, do not pull it sharply - you can tear off the temperature sensor wires. It is better to first unscrew the screws by 70%, then carefully move the lampshade to the side.

What to do if the screw turns but does not come out?

In this case, the thread inside the plastic housing of the lampshade is torn off. Solutions:

1. Carefully break out the lampshade (if. it is already cracked) and replace it with a new one.

2. Drill a hole above the screw and insert a new self-tapping screw with a nut.

3. Use a screw of a larger diameter (for example, take M4 instead of M3), but this is risky - you can split the body.

Rotary lamps: how to remove without breakage

Rotary clamps are used LG, Whirlpool and some models Liebeherr. The main difficulty is determining the direction of rotation. In 90% of cases, the lamp scrolls counterclockwise, but in LG DoorCooling+ (for example, LG GA-B489 YDQZ) - clockwise.

Algorithm Actions:

1. Press the lampshade up (as if you were trying to press it into the ceiling of the chamber). This will unlock the rotating mechanism.
2. Turn the lampshade 10–15° in the desired direction. There should be a click.
3. Lower the lampshade down and pull it towards you. If it doesn’t work, try turning it another 5°.

In models Whirlpool with the system 6th Sense the lampshade is connected to the door opening sensor. If you tear off the cable during dismantling, the refrigerator will sound an alarm every time it is opened. Before removing the lampshade disconnect the connector (it is usually white with a latch).

Magnetic and hidden fastenings: instructions for difficult cases

Magnetic shades (Bosch, Siemens) and models with hidden grooves (Atlant, Stinol) require a special approach. The main thing here is not to use force, otherwise you will break the latches or damage the camera body.

For magnetic mounts:

• 🧲 Take the lampshade with both hands and pull downand not towards you. Magnets are usually located in the upper part.
• 🧲 If the lampshade does not budge, pry it off with a screwdriver at one of the corners. In Bosch KAN92VI30 the magnets are weak - a knife blade is enough.
• 🧲 After removal, check the magnets for rust. Clean them with alcohol, otherwise the shade will fall off during vibration.

For hidden grooves (for example, in Atlant XM 4425-100):

1. Press on upper edge of the lampshade and pull it towards you. In most cases there is a latch hidden there.
2. If that doesn’t help, use a flashlight to illuminate the inside of the lampshade - sometimes the grooves are visible at a certain angle.
3. As a last resort, use plastic a spatula (for example, for removing smartphone screens) so as not to scratch the case.

⚠️ Attention: In refrigerators Stinol the lampshade is often attached to thermostatIf it is torn off the wires, you will have to adjust the temperature mode again before dismantling. take a photo of the connection of the contacts!

What to do after removing the lampshade: diagnostics and replacement

When the lampshade is finally removed, check:

• 💡 Light bulb - if the filament is torn or the bulb has turned black, it is required replacement. For LED-lamps, check the integrity of the tracks on the board.
• 🔌 Contact -clean oxidized or burnt ones with an eraser or alcohol. Samsung the “negative” contact (it) is often oxidized. wider).
• 📏 Diffuser —if there are cracks or cloudiness on it, replace it (cost ~300–500 rubles).
• 🔗 Wires —in refrigerators with No Frost check whether the insulation is rubbed against the body fan.

When replacing a light bulb:

• For LEDlamps, observe the polarity! “Plus” is usually marked with a red wire or dot on the base.
• B models Liebherr c BioFresh use only original lamps (Liebherr 6170430), otherwise the humidity sensor will malfunction.
• After installing the new lamp, turn on the refrigerator and check if the light flickers. Flickering indicates a bad connection or a faulty driver. LED-module.

If after replacement the light does not light:

1. Check fuse (in some models Indesit it is located on the lampshade board).
2. Test door switch -press it with a screwdriver. If the light comes on, the problem is in the door mechanism.
3. In refrigerators with electronic control (Samsung Family Hub) the lighting error is reset through the menu: Settings → Diagnostics → Lamp reset.

FAQ: Frequently asked questions about lamps in the refrigerator

Is it possible to use a light bulb with a higher power than indicated in the instructions?

No! In refrigerators with plastic lampshades (Beko, Vestfrost), a lamp more powerful than 15W will melt the housing. For LED-lamps, focus on luminous flux (optimally 200–300 lumens In models LG With DoorCooling+ a powerful lamp can overheat the temperature sensor.

The lampshade is cracked, but the light bulb is intact. Is it possible to operate the refrigerator?

Cracked diffuser. allows moisture to pass through, which leads to:

• Short circuit of contacts (risk of fire!).
• Oxidation of the board LEDmodule (in Samsung and Bosch).
• Ingress fragments into the products.

Replace the lampshade (cost ~800–1500 rubles) or at least seal the crack food-grade silicone (temporary solution).

How to remove the lampshade in refrigerator Atlant two-chamber?

In most models Atlant (for example, XM-4626-089) the lampshade is mounted on hidden grooves. Algorithm: Atlant data-i="270">upper right corner

1. Click on upper right corner lampshade and pull it towards you.
2. If it doesn’t budge, pry it up with a screwdriver bottom edge (the latch is hidden there).
3. In the freezer, the lampshade can be secured with a screw under star —use a cue ball Torx T10.

⚠️ Do not use force—in Atlanta the lampshade is often connected to the thermostat!

After replacing the light bulb, the light blinks. What is the reason?

Probable causes:

• Bad contact - check whether the metal “antennae” in the socket is bent.
• Faulty driver (in LED-lamps). lamps. LG And Samsung The driver is built into the lampshade - the entire unit will need to be replaced.
• Polarity reversal - Swap “+” and “−” on the lamp contacts.
• Control module failure (in refrigerators with a display). Reset: turn off the power for 5 minutes.

Where to buy spare parts for the lamp?

Look for original spare parts:

• On manufacturers' websites (Samsung Parts, Bosch Service).
• In stores like "220 Volt", "AllInstruments.ru"** (there are catalogs by model).
• On AliExpress (cheaper, but wait 2-4 weeks). To search, use the article number on the sticker on the back wall of the refrigerator.

For LEDmodules are suitable. universal lamps T5 12V with a base G4 or G5.3 (for example, Osram LED Superstar).