How to properly remove the tray in a Beko refrigerator: instructions with photos and videos

The tray in the refrigerator Beko is an important, but often underestimated design element. It collects condensation, preventing the formation of puddles under equipment and protecting the compressor from moisture. However, over time, the pan becomes dirty, moldy, or cracked and must be removed for cleaning or replacement. In this article we will look at how to do this yourself without damaging the refrigerator or interfering with its operation.

The process of dismantling the tray in models Beko (for example, CN 329220 X, GNE 114120 X or DS 333020) has general principles, but may differ in detail depending on the series and year of manufacture. We will take these nuances into account and also give recommendations on choosing tools and caring for the removable part. If you have never disassembled a refrigerator, do not worry: with the right approach, the task will take no more than 20–30 minutes.

Before you begin, make sure that the refrigerator is unplugged. This is not only a safety issue, but also a necessity for some models Beko, where the tray is fixed with latches that are sensitive to vibrations of the operating compressor.

Preparing to remove the pan: tools and precautions

Before removing the pan, prepare everything you need. In most cases, you will not need specialized tools, but some models Beko (for example, series Frost Free) may have hidden fasteners, for which you will need a screwdriver or pliers.

Here is what you need to prepare:

• 🔧 Flat screwdriver (for prying latches or unscrewing screws in old models).
• 🧽 A rag or sponge —the tray is often wet and needs to be dried before cleaning.
• 🧴 Detergent (for example, Cillit Bang or Sano to remove mold).
• 📦 Water container —if the tray is full of condensation, it will have to be drained.
• 🔦 Flashlight —the lighting under the refrigerator is usually weak.

Pay special attention to safety:

• ⚡ Unplug the refrigerator from the outlet 10-15 minutes before starting work. This will eliminate the risk of electric shock and give the compressor time to cool down.
• 🧤 Wear gloves —the tray may be covered with mold or rust.
• 🚫 Do not use sharp objects to pry up the tray if you are not sure of the location fastenings. Risk of damaging the drainage system or compressor tubes.

⚠️ Attention: In refrigerators Beko with a system No Frost the tray may be part of a complex condensate drainage system. If you are not sure of your actions, it is better to contact a service center - incorrect dismantling will lead to leaks or breakage of the fan.

Where is the tray in the Beko refrigerator and how to get to it

The tray in refrigerators Beko located at the bottom of the rear wall, directly above the compressor. In most models it is hidden by a decorative panel, which must first be removed. In some series (for example, Beko RCN), the tray may be partially covered with a plastic grill or even a metal screen.

To gain access:

1. Move the refrigerator 30–40 cm from the wall. Be careful not to damage the floor or twist the drainage system hose.
2. Remove the lower decorative panel. It is usually secured with latches or two screws (in models before 2018). Carefully pry it off from the side with a screwdriver.
3. If the tray is covered with a grill, unscrew it (usually 2-4 screws). In series Beko GNE the grille can be plastic and can be removed without tools.

After this you will see the tray itself - a white or gray plastic container with a tube for draining condensate. In models with No Frost the tray can be integrated into the ventilation system, and its dismantling will require additional actions (more on this below).

What to do if the tray is not visible?

In some refrigerators Beko (for example, series Beko BCD) the tray is hidden behind the back wall and attached to the drainage hose. In this case you will have to:

1. Unscrew the back panel (usually 4-6 screws).

2. Carefully disconnect the hose from the pan, after draining the water from it.

3. Only after this, pull the tray forward.

If you are not sure, it is better to call a technician, since the risk of damaging the drainage system is high.

Step-by-step instructions: how to remove the tray in a Beko refrigerator

The dismantling process depends on the type of attachment of the tray. We will look at the three most common options, which cover 90% of models Beko.

Option 1: Tray with latches (most models)

This is the simplest case. The tray is held in place by plastic latches on the sides and front. To remove it:

1. Make sure the tray is empty. If there is water in it, drain it into a prepared container.
2. Gently press the latches on both sides of the tray (usually they are located closer to the front).
3. Pull the tray towards you - it should come out of the grooves.

Option 2: Screw-on tray (old models or series with No Frost)

In refrigerators Beko manufactured before 2017 or in models with a system No Frost (for example Beko DS 333020), the tray can be secured with screws. You will need a screwdriver:

1. Unscrew the 2-4 screws holding the pan (usually located in the corners).
2. If the pan is stuck to the base, carefully pry it off with a screwdriver, starting from the front edge.
3. Disconnect the drain hose (if it is attached to pan).

Option 3: The pan is integrated into the ventilation system (Frost Free series)

In the most modern models Beko (for example, Beko GNE V320) the pan can be part of a complex condensate drainage system. Here you will need:

1. Turn off the refrigerator and wait until the ice in the system melts (2-3 hours).
2. Remove the back panel by unscrewing 4-6 screws.
3. Disconnect the drain hose and ventilation tubes from the pan.
4. Carefully remove the tray without damaging the humidity sensors (they can be attached nearby).

Disconnected the refrigerator from the mains|

Prepared the water container|

Checked the presence of tools|

I made sure that the pan is not integrated into the No Frost system|

I photographed the location of the hoses (if any)

-->

In models Beko with a display on the door (for example, Beko BCSS 500) after removing the pan it may work error E1 or E4related to the humidity sensor. To reset it, turn off the refrigerator for 5 minutes, then turn it on again.

Cleaning and replacing the tray: tips and mistakes

After removal, the tray must be cleaned of dirt, mold and plaque. Use warm water with detergent (for example Domestos or Sano Anti-Plesen). Do not use abrasive sponges - they will scratch the plastic, and new mold will appear in microcracks faster.

If the pallet is cracked or deformed, it must be replaced. Original spare parts for Beko can be found by article number:

• 📌 For models CN 329220 X — article number 2405000100.
• 📌 For series GNE — article 2405000200.
• 📌 For No Frost — article 2405000300 (complete with drain hose).

When When installing a new pallet, make sure that:

• 🔹 The drainage hose is connected tightly (otherwise water will drip onto the floor).
• 🔹 The latches or screws are secured evenly, without distortions.
• 🔹 The pallet fits into the grooves until the characteristic click (in models with latches).

⚠️ Attention: If, after installing the pan, the refrigerator begins to make noise or vibrate more strongly, check whether the pan is touching the compressor. In some models Beko (for example Beko DS) there must be a rubber gasket between the pan and the compressor - do not lose it during dismantling!

Nuances for different Beko models

The design of the tray may differ depending on the series of the refrigerator. We have collected key features for popular lines Beko:

If your model is not indicated in the table, pay attention to the year of manufacture:

• 📅 Before 2015: probably, the pan is fastened with screws, and the drainage system is metal.
• 📅 2016–2020: most often latches, but combined fastenings are possible.
• 📅 After 2020: the pallet can be part of the system No Frost, requires care.

What to do if the pallet cannot be removed?

Sometimes the pallet “sticks” to the base or is held in place by hidden fasteners. Here's what you can do:

Problem 1: The tray does not come out of the grooves.

• 🔹 Check that all the latches are pressed out. Sometimes they are hidden under a layer of dust.
• 🔹 Gently move the pan left and right - this will help free it from plaque.
• 🔹 Use silicone grease (for example, WD-40) to facilitate sliding.

Problem 2: Screws will not come out.

• 🔹 If the screws are rusty, apply a coat WD-40 and wait 10 minutes.
• 🔹 Use a screwdriver with a magnetic tip to prevent the screws from falling in refrigerator.
• 🔹 As a last resort, carefully drill out the screws with a drill (drill diameter - 3 mm).

Problem 3: The drainage hose does not detach.

• 🔹 Do not pull the hose by force - it may crack. Carefully twist it around the axis.
• 🔹 If the hose is stuck, heat the connection with a hairdryer (temperature no higher than 60°C).
• 🔹 In models No Frost the hose can be soldered - in this case it is better to call a specialist.

⚠️ Attention: If during dismantling you hear a crash or see that the drainage hose has come off the pan, stop work immediately. In this case, the hose will need to be replaced, otherwise condensation will accumulate inside the refrigerator, which will lead to corrosion or a short circuit.

How often should you clean the tray and when to change it?

The tray in the refrigerator Beko requires regular care. Recommended cleaning frequency:

• 🧼 Every 3 months: rinsing with warm water and detergent.
• 🧽 Every 6 months: deep cleaning with mold removal (use Sano Anti-Plesen or vinegar solution).
• 🔄 Every 1–2 years: check the integrity of the pan and drainage hose.

The pan must be replaced in the following cases:

• 🔥 The pan is cracked or deformed (even a small crack will lead to leaks over time).
• 🍄 Mold is not removed even after cleaning with aggressive means.
• 💧 The drainage hose has become torn from the pan and cannot be repaired.
• 🔊 The pan has started rattle when the compressor operates (this is a sign of wear on the fasteners).

If you notice that water is constantly accumulating under the refrigerator, it is not always the fault of the pan. Possible reasons:

• 🔍 Clogged drainage hole in the refrigerator compartment (cleaned with wire or a special brush).
• 🔍 Malfunction of the defrosting system (in models with No Frost).
• 🔍 Damage to the door seal, which causes too much condensation.

Video instructions and additional resources

If you perceive information better visually, we recommend watching video instructions for dismantling the tray in refrigerators BekoPay attention to models similar to yours:

🎥 For models with latches (CN series, RCN):

• Video: “How to remove the tray in Beko CN 329220 X” (search on YouTube).
• Key point: demonstration of the location of the latches and the method of pressing them.

🎥 For models with No Frost (GNE series, DS):

• Video: “Disassembling the No Frost system in Beko GNE 114120 X” (pay attention to the stage with the tray).
• Key point: how to disconnect the drain hose without damage.

📄 Official resources:

• Operating instructions for your model can be downloaded on the website Beko (section "Support").
• Spare parts catalog with pallet part numbers: Beko Spare Parts (available for Europe and the CIS).

If you haven't found it video for your model, pay attention to the universal rollers for cleaning the drainage system. The principle of operation of the tray in refrigerators Beko is similar to other brands (Indesit, Ariston), so the instructions can be interchangeable.

⚠️ Attention: Details of the design may vary depending on the year of manufacture of the refrigerator. For example, in models Beko 2023–2026, the tray is often equipped with an overflow sensor, which cannot be damaged during dismantling. If your refrigerator is new, check the details with the service center.

FAQ: Frequently asked questions about trays in Beko refrigerators

🔹 Is it possible to wash the tray in the dishwasher?

No, this is not recommended. High temperatures and aggressive detergents can deform the plastic or damage the drainage holes. It is better to wash the tray manually with warm water and a mild detergent.

🔹 Why did the refrigerator become louder after cleaning the tray? work?

The pan is probably installed incorrectly and is touching the compressor or fan. Turn off the refrigerator, check the position of the pan and, if necessary, correct it. Also make sure that all screws or latches are secured evenly.

🔹 How can you tell if the pan is cracked if water does not flow?

Inspect the tray for microcracks (they can be almost invisible). Also signs are: increased humidity under the refrigerator, rust on the compressor or an unpleasant smell from under the equipment. If the tray is old (5+ years), it is better to replace it preventively.

🔹 Is it possible to use a tray from another Beko model?

Only if the articles are the same or the pallet is identical in size and location of the fasteners. In models with No Frost the pallets are often unique for each series. Before purchasing, check the article numbers or show a photo of the pallet to the spare parts seller.

🔹 What to do if after removing the pallet from the refrigerator. is water flowing?

Most likely, you damaged the drainage hose or did not connect it tightly to the pan. Turn off the refrigerator, check the hose for cracks and reconnect it, using silicone sealant for reliability. If the hose is torn, it needs to be replaced.