Assembling brand refrigeration equipment Atlant often raises questions among users, especially when it comes to joining the upper and lower cameras. Many models are supplied disassembled for ease of transportation, and the quality of installation determines the further tightness and energy efficiency of the device. Correct connection guarantees the absence of distortions, which can lead to loose fitting of the doors and leakage of refrigerant.
The installation process requires attention to detail, since the design of the Belarusian manufacturer has its own technological features. Don't rely solely on visual assessment; it is necessary to strictly follow the algorithm of actions prescribed in the technical documentation. Errors at the installation stage can cause increased compressor noise or disruption of air circulation inside the system.
In this article we will look in detail at how to connect a refrigerator and freezer Atlantto ensure their long and stable operation. You will learn about the nuances of installing fasteners, adjusting the legs and checking the tightness of the circuit. Compliance with these rules will avoid costly repairs in the future.
Preparatory work and selection of installation location
Before proceeding with the physical joining of the blocks, it is necessary to prepare the room and the unit itself. Horizontal surface the floor is a critical condition; any misalignment will lead to a shift in the center of gravity and problems with closing the doors. It is recommended to clear the space in advance in order to have access to the equipment from all sides.
Packaging materials should be removed carefully so as not to damage the enamel coating or plastic elements. Pay special attention to the shipping bolts if they are present in your model, although in modern refrigerators Atlant they are often replaced with special compressor clamps. They must be removed before turning on.
⚠️ Attention: Do not install the refrigerator near heating appliances or in direct sunlight. This can lead to overheating of the capacitor and increased power consumption.
It is important to check the completeness of all parts included in the assembly kit. Typically the box contains decorative panels, mounting bolts, handles and documentation. The absence of even one screw can complicate the installation process or make it impossible without searching for analogues.
☑️ Preparation for assembly
Joining the upper and lower chambers
The main stage of assembly is to connect the refrigerator compartment with the freezer compartment. The design of most models Atlant involves installing the upper block on the lower one and then fixing it. This requires the help of a second person, since the weight of the cameras is significant and there is a high risk of dropping the equipment or damaging the floor.
First make sure that the back panels of both units are aligned with each other. At the ends of the chambers there are special holes for fastening bolts, which ensure the rigidity of the structure. Joint seam Should be minimally noticeable, and the gaps should be uniform across the entire width.
Use the original fasteners included in the delivery kit. The bolts should be tightened evenly, alternating sides to avoid distortion. Excessive tightening force can lead to metal deformation or thread breakage, so proceed carefully.
After physically installing the blocks, check the tight fit of the upper part to the lower part. In some modifications, a sealing tape is laid between the chambers, which must not be damaged or crushed. The tightness of this connection affects the thermal insulation of the entire unit.
Installation of decorative panels and handles
The appearance of the refrigerator Atlant form decorative elements that hide fastening points and joints. The panels are usually installed on the front of the doors and secured with latches or screws. It is important not to confuse the top and bottom panels if they have different designs or sizes.
Installation of the handles is done last, when the main blocks have already been assembled. Each door has its own mounting configuration, so carefully study the markings on the inside of the handles. Symmetrical installation critical for aesthetics and ease of use.
| Element | Mounting type | Tool | Installation nuances |
|---|---|---|---|
| Top panel | Latches + screws | Phillips screwdriver | Remove the protective film after installation |
| Bottom panel | Screws | Key (included) | Requires precise alignment of holes |
| Door handle | Hidden bolts | Hexagon | Tighten crosswise |
| Plinth (bottom) | Latches | Without tools | Serves for ventilation of the compressor |
If your model has decorative covers on the hinges, they are installed after hanging the doors. These elements protect the metal from corrosion and give it a finished look. Make sure that they do not prevent the doors from opening at full angle.
Adjusting supports and doors
After connecting the chambers and installing the panels, it is necessary to make a final adjustment to the position of the refrigerator. Support legs allow you to compensate for uneven floors and set the equipment strictly at level. Tilt back by 1-2 degrees ensures automatic closing of the doors under the influence of gravity.
By rotating the front adjustable supports, achieve a stable position of the body. The refrigerator should not wobble when lightly pressing on the corners. If the floor is slippery, it is recommended to use special pads under the feet to increase traction.
⚠️ Attention: Do not leave the refrigerator in a skewed state. This creates additional load on the compressor and can cause vibration of the pipelines, which will lead to freon leakage.
Next, you should check the tightness of the door seals. The door should close easily, but with a characteristic bang in the last centimeters. If the door does not fit tightly, it may be necessary to adjust the hinges or rehang the door to the other side, which is also provided for by the design Atlant.
How to rehang the door?
To rehang the door, you need to remove the handles, dismantle the hinges on one side and move them to the opposite, after closing holes with decorative plugs.
Initial launch and setting modes
After completion of installation work, the refrigerator should stand in an upright position for at least 2-3 hours (and if it was transported lying down - up to 24 hours). This is necessary to allow oil to drain into the compressor. Only after this can the unit be connected to the network.
It is better to start the first time without loading products. Let the equipment run idle for about 6-10 hours so that it reaches operating mode and cools down to the set temperatures. Thermoregulator at this time it should be set to the middle position.
Modern models Atlant equipped with electronic control, allowing precise adjustment of the climate in each chamber. It is recommended to set the temperature in the refrigerator compartment to +4°C and in the freezer to -18°C. These values are optimal for long-term storage of products.
Frequent errors during assembly and their consequences
Inexperienced users often neglect the instructions, which leads to various malfunctions. One common mistake is to ignore ventilation gaps. The refrigerator Atlant requires free space at the back and sides to remove heat from the condenser.
Another mistake is the incorrect tightening sequence of the mounting bolts. If you twist one side completely first, the opposite side may not meet, causing a gap to form. Moisture and dust can get into this gap, causing corrosion or a short circuit.
- 🔴 Forgotten transport wedges lead to a loud knocking sound from the compressor during operation.
- 🔴 Overtightened panel screws can split the plastic or deform the door.
- 🔴 Failure to check the level causes the doors to open spontaneously.
It is also worth mentioning damage to the seals due to careless assembly. Microcracks in rubber are difficult to notice immediately, but over time they lead to the formation of ice and increased energy consumption. Carefully inspect the elastic band around the perimeter after each stage of installation.
⚠️ Attention: Technical characteristics and design of models may vary slightly depending on the year of manufacture. Always check the product data sheet included with your specific model.
Questions and answers (FAQ)
Is it possible to install the Atlant refrigerator close to the wall?
No, for normal operation of the cooling system it is necessary to leave a gap of at least 5-7 cm between the back wall of the refrigerator and the wall. This ensures air circulation and efficient heat removal from the condenser.
What to do if there is a visible gap after connecting the chambers?
A small gap may be a design feature, but if it is too large, check that the mounting bolts are installed correctly. It may be necessary to loosen them and realign the blocks, pressing them lightly together before final tightening.
Do the hinges need to be lubricated before installing the doors?
Factory grease on refrigerator hinges Atlant usually lasts a long time. Additional lubrication is not required and may cause oil to leak onto the seal or products. If the hinges creak after a while, use a special silicone lubricant.
How many hours after installation can you load products?
After the initial switching on, it is recommended to wait at least 6-8 hours until it is completely frozen and the temperature stabilizes. Loading warm food into a refrigerator that has not cooled down will increase the load on the compressor.
Is it possible to connect chambers without an assistant?
It is strictly not recommended. The top chamber is heavy and bulky, making it difficult to hold and fit into the mounting holes at the same time. The risk of dropping the unit and damaging the floor or equipment is very high, so involve a second person to help.