After delivery of new household appliances or moving to a new apartment, the owner inevitably faces the question of how to properly start up the equipment. Refrigerators of the brand Hotpoint Ariston are famous for their reliability and thoughtful functionality, however, the procedure for their initial activation requires compliance with certain time intervals and sequence of actions. Ignoring the basic rules of transportation and settling can lead to failure of the compressor, which is the heart of the entire cooling system.
Modern models are equipped with complex electronics that control temperature conditions, so it is important not just to plug the plug into the socket, but also to correctly initialize the control system. In this article we will analyze in detail all the stages: from the moment of removing the transport fastenings to setting intelligent modes freezing. Understanding the physical processes occurring inside the unit during the first hours of operation will help you avoid common mistakes and extend the life of the device.
Please note that the algorithm of actions may vary slightly depending on the series of your device, be it a classic two-chamber model or a modern one. Side-by-Side. The main attention should be paid to stabilizing the refrigerant and checking the electrical network, since power surges at the time of start pose the greatest danger to electronic module control.
Preparation of equipment after transportation
The first and most critical The stage is the time delay after delivery. If the refrigerator was transported in a horizontal position or at a strong tilt, oil from the compressor could leak into the cooling system circuits. To return the oil to the compressor crankcase and evaporate moisture, it is necessary to leave the unit in a vertical position, disconnected from the network for at least 4 hours, and in winter it is recommended to increase this interval to 8 hours.
In parallel with settling, it is necessary to carry out a visual inspection and remove all transport elements. Manufacturers often use rigid latches for doors and interior shelves, which, when activated, can damage the plastic or break the seal. You should also remove the protective film from the external and internal surfaces, as it interferes with normal air circulation and heat exchange.
Pay special attention to the ventilation system. Make sure that the gap between the back wall of the refrigerator and the wall of the room is at least 5-7 centimeters. Insufficient heat removal from the condenser will lead to overheating refrigerant and increased load on the engine, which in the first hours of operation can trigger an emergency shutdown.
⚠️ Attention: Never turn on the unit immediately after bringing it in from the street in winter. A sudden change in temperature can cause the formation of condensation inside electrical circuits, which will lead to a short circuit.
Checking the electrical network and connecting
Refrigerators Hotpoint Ariston require a stable voltage in the network for the correct operation of inverter compressors and No Frost systems. Before connecting, make sure that the outlet is properly grounded and meets power standards. The use of extension cords or tees is not recommended, as they can create additional resistance and heat, especially with starting currents.
When first turned on, there may be a short-term spike in energy consumption, which is normal during the engine starting process. If voltage surges frequently occur in your apartment, it is advisable to install a stabilizer or use a surge protector with an overload protection function. This will save electronic controller from combustion.
After connecting to the network, the device does not start cooling immediately. The system performs self-diagnosis, which can last from a few minutes to half an hour. At this time, do not open the doors or try to activate additional functions, so as not to disturb the calibration temperature sensors.
Activation of the control panel and display
In most modern models Hotpoint Ariston the control panel switches to active mode automatically after power is applied. However, some series require manual activation. Find the button with the on/off symbol on the panel or hold down the temperature setting key for 3-5 seconds until the indication appears on the display.
If the screen does not light up, check whether the Demo Mode, which is often used in sales areas, is activated. To disable it, you may need to simultaneously press two buttons, the combination of which is indicated in the instructions for a specific model. After exiting demo mode, the refrigerator will begin to gain temperature.
| Indicator on display | Value | User action |
|---|---|---|
| Flashing temperature | Cooling process in progress | Waiting for stabilization |
| The "!" or Alarm | Temperature Excess | Check closing tightness |
| Snowflake | Frozen mode | Control of freezer operation |
| Key | Panel lock | Unlock according to instructions |
It is important to distinguish between normal operation signals and error codes. If a flashing alarm indicator appears on the display, this does not always mean a breakdown. Often this is a signal that the internal temperature has not yet reached the set values, which is quite natural for first startup.
Setting temperature modes
After activating the display, you need to set the optimal operating parameters. Factory settings are usually +4°C for the refrigerator compartment and -18°C for the freezer. For models with a system Total No Frost these values are the most energy efficient and safe for storing most products.
Adjustment is carried out using touch buttons or a rotary control, depending on the series. Temperature changes occur step by step, usually in 1 degree increments. It is not recommended to immediately set extremely low values, as this will force the compressor to work at its limit unnecessarily.
☑️ Initial setting of the refrigerator
If you plan to load a large number of products at the same time, you can temporarily activate the mode Super Freeze (super freezing). This function causes the compressor to work continuously, quickly reducing the temperature. However, you cannot use it constantly, as this leads to accelerated wear of parts.
⚠️ Attention: Do not set the temperature below -20°C in the freezer unless absolutely necessary. This will not improve the quality of storage, but will significantly increase energy consumption and the load on the system.
First loading with food
It is recommended to load the refrigerator with food only after it has been empty for 2-4 hours and reaches the specified temperature. A sudden influx of large amounts of heat from food can disrupt the initial stabilization process and cause the system to operate in emergency mode.
Distribute food evenly without blocking the ventilation openings. In models with No Frost air circulation is critical to prevent the formation of ice and ensure the same temperature in all zones. It is better to place meat and fish on the lower shelves or in the freshness zone, where the temperature is lowest.
Why can’t you put hot food?
Placing hot dishes in the refrigerator causes a sharp jump in humidity and temperature, which leads to the formation of condensation on the walls, the growth of bacteria and increased load on the compressor trying to compensate for the heat.
Make sure that the food does not fit tightly against the back wall of the chamber, especially in older models with a drip defrosting system. In modern Hotpoint Ariston with a fan, this risk is less, but compliance with