Modern refrigerators of the brand Beko are equipped with electronic control panels that require correct activation after installation. Unlike older mechanical models, it is not enough to simply insert the plug into the socket. The electronics must undergo initial initialization, and the compressor must start in gentle mode. Incorrect switching on may result in the display not lighting up or the cooling system not working.
The first thing you need to do is to ensure that the equipment is at rest. After transportation, especially if the refrigerator was lying on its side, compressor oil could flow into the system circuit. If you start the unit immediately, oil will enter the capillary tube, causing blockage and failure. The minimum settling time is 4 hours, but to guarantee it is better to wait 8-12 hours at room temperature.
It is also important to check the condition of the electrical network. Refrigerators Beko with inverter compressors are sensitive to voltage surges. Make sure the outlet is in good working order, grounded, and meets amperage requirements. The use of extension cords or tees is undesirable, as this creates the risk of poor contact and overheating of the wiring.
Primary preparation and installation of equipment
Before pressing the buttons on the panel, make sure that the refrigerator is installed correctly. The floor should be level and the legs should be adjusted so that the door closes automatically under the influence of gravity when released at an angle. Gaps to walls and furniture should be at least 5 cm for free air circulation. If ventilation is impaired, No Frost system will not be able to effectively remove heat, and the compressor will wear out.
The internal space should be cleared of all transportation materials. This applies not only to cardboard and foam plastic, but also to tape that can be used to seal shelves or drawers. Pay special attention to the condensation tray, which is often located above the compressor at the rear. It must not be removed or moved, as it is part of the moisture removal system.
⚠️ Attention: Do not connect the refrigerator to the mains if you notice mechanical damage to the power cord or plug. The operation of such equipment is prohibited by safety rules.
After external inspection and installation in place, you can begin the electrical connection. Insert the plug into the outlet. At this point, you may hear a quiet clicking or buzzing sound - this is normal. The electronic control board begins to receive power, but the compressor will not start yet. The system performs self-diagnosis of temperature sensors.
☑️ Preparation for the first start
Activation of the control panel and display
Models Beko with a display may behave differently immediately after voltage is applied. On some models, the screen lights up immediately, displaying the current temperature in the chambers. On others, the panel may remain dark until you press the activation button. Most often this is a button Power or On/Off.
If the display does not light up on its own, find the power button on the control panel. It can be separate or combined with a temperature controller. Press and hold this button for 3 seconds. You should hear a beep and the screen should light up. If this does not happen, check whether the “Demo” or “Store” mode is activated, which is sometimes turned on at the factory for display cases.
In some series of refrigerators, for example, in the line Beko NeoFrost, the interface may be touch-sensitive. In this case, the touch should be confident, but not strong. With dry fingers, press the power icon. If the screen responds with a delay, do not panic - the processor takes time to load the operating control system. In rare cases, a factory reset may be necessary. To do this, unplug the refrigerator for 10–15 minutes and then turn it on again. This will help the electronics reboot and correctly determine the configuration of the connected modules.
on-line control system. In rare cases, a factory reset may be necessary. To do this, unplug the refrigerator for 10–15 minutes and then turn it on again. This will help the electronics reboot and correctly determine the configuration of the connected modules.
Setting temperature modes
After turning on the display, you need to set the optimal operating parameters. Factory settings are usually +4°C for the refrigerator compartment and -18°C for the freezer. These values are suitable for most products. However, if you plan to load a lot of fresh food, you can temporarily turn on the mode Super Cool or Super Freeze.
To change the temperature, use the arrow buttons or the “+” and “-” symbols on the panel. Press them briefly. The indicator of the selected camera will flash on the display. After a few seconds the flashing will stop and the new values will be stored in memory. It is not recommended to set the temperature below +2°C in the main chamber, as this can lead to freezing of vegetables.
The freshness zone deserves special attention, if provided by the model. Some refrigerators Beko have a separate compartment HarvestFresh or similar, where a special microclimate is maintained. The temperature there can be adjusted independently. Make sure that the dampers in this compartment are open if you plan to store herbs or fruits there.
⚠️ Attention: Compressor operating parameters and temperature accuracy may vary depending on the specific model and software version. Check the sticker inside the chamber or the official manual for your series.
If you use the Eco Mode function, the refrigerator will maintain the minimum required temperature so that food does not spoil, but energy is used sparingly. In this mode, the light in the chamber may not light up when the door is opened, and the ventilation operates intermittently.
First load with food
An empty refrigerator gains temperature faster, but a stable cold background is formed only in the presence of heat-intensive items. Products play the role of cold accumulators. However, you cannot load all shelves immediately after switching on. The compressor will not have time to cool a large volume of warm mass and will work without stopping, which will lead to overheating.
It is recommended to wait 2-4 hours after turning on the empty refrigerator. During this time it will return to operating mode. Then start loading in small portions. Place food in the freezer first if it needs to be frozen, and only then fill the main compartment. Distribute the food evenly without blocking the ventilation holes.
- 🥩 Immediately place meat and fish in the lower drawers or freshness zone.
- 🥛 It is better to place dairy products on the middle shelves, where the temperature is most stable.
strong.
- 🥬 Store vegetables and fruits in lower containers to prevent them from being damaged by the cold.
Do not place hot or warm foods inside. This will sharply increase the humidity and temperature, forcing the system No Frost to work in enhanced mode. In addition, condensation can freeze on food, ruining its appearance. Allow the food to cool to room temperature before placing it in the chamber.
Diagnosis of possible startup problems
Sometimes, after switching on, users encounter non-standard behavior of the equipment. The display may flash, go dark, or show error codes. Most often, this is not a breakdown, but a feature of the electronics. For example, a flashing temperature indicator may indicate that the chamber is still warm and active cooling is in progress.
If you hear gurgling, hissing or clicking sounds, this is normal. The refrigerant moves through the tubes, and valves switch the flow. Fan noise is also standard for models with the system NeoFrost. However, if the noise is accompanied by chassis vibration, check the adjustment of the feet. The refrigerator should not wobble.
The table below shows the indicators and their meaning at start:
| Indicator | Value | Action |
|---|---|---|
| Temperature flashing | Cooling in progress | Wait for stabilization |
| Alarm is on | Temperature is above normal | Check the door tightness |
| Snowflake | Frozen mode | Normal operation |
| Lock | Button lock | Unlock by holding |
If appears on the display letter F or code like E1, E2, this indicates a malfunction of the sensor or defrost system. In this case, you need to disconnect the device from the network for 15 minutes. If the error persists after restarting, call a specialist. Repairing electronics yourself can lead to complete failure of the control board.
⚠️ Attention: Do not attempt to disassemble the back panel or remove covers while the refrigerator is under warranty. This will lead to loss of the manufacturer's warranty.
Frequently asked questions (FAQ)
How long does it take for a Beko refrigerator to reach temperature after switching on?
Usually it takes from 2 to 6 hours to reach operating mode. It may take up to 24 hours for the temperature in all drawers and shelves to completely stabilize, especially if the chamber was fully loaded with products at once.
Why does the display go dark after a while?
This is a normal energy saving mode. The screen turns off to avoid wasting energy and overheating. When you touch any button or open
t door, the display will light up again. If the screen does not respond to touches, check whether the control panel is locked.
Can a Beko refrigerator be connected to the network via an extension cord?
Manufacturers do not recommend using extension cords. If the outlet is far away, use only a high-quality surge protector with grounding and a rated current of at least 16A. Thin household extension cords can melt.
What to do if the refrigerator hums more than usual after turning it on?
In the first hours of operation, the compressor may work more intensely to cool the chamber volume. Also check that the tubes are not touching the wall or furniture from behind. If the humming is accompanied by knocking or clanging, stop the appliance and call a technician.
Do you need to wash the refrigerator before turning it on for the first time?
Yes, definitely. Wipe the interior surfaces with warm water and a mild detergent to remove dust and new plastic odors. After this, wipe all the shelves dry and leave the doors open for 30 minutes for ventilation.