Buying a new household appliance or bringing it back to life after a long defrosting is always an exciting moment, requiring compliance with certain technical nuances. Correct launch of refrigeration equipment brand Indesit is a critical stage on which the durability of the compressor and the quality of product refrigeration directly depend in the future. Many users make the fatal mistake of turning on the device immediately after delivery or washing, which can lead to the failure of expensive equipment.
Modern two-chamber models Indesit are equipped with complex refrigerant circulation systems that are sensitive to temperature changes and positions in space. Before inserting the plug into the socket, you must make sure that the device has gone through all stages of acclimatization and preparation. Ignoring these rules may void the manufacturer's warranty, so you should carefully study the sequence of actions before the first start.
In this article we will analyze in detail all stages of preparation, from choosing the installation location to temperature settings. You will learn why you should not turn on the device immediately after transportation and how to check its performance without load. A competent approach will allow you to avoid common mistakes and ensure stable operation of the refrigerator compartment over many years of operation.
Primary preparation and selection of installation location
The first step towards a successful launch is the correct placement of the unit. Double-chamber models Indesit require free space around the housing for effective ventilation of the condenser. If you install the device close to a wall or furniture, heat transfer will be disrupted, which will lead to overheating compressor and increased energy consumption.
It is necessary to provide a gap of at least 5-10 centimeters from the back wall of the device to the wall of the room. Side space is also important, especially if the refrigerator is built into a niche in the kitchen unit. The air must circulate freely, removing the heat generated during operation of the refrigeration circuit.
⚠️ Attention: Never install Indesit near heat sources such as gas stoves, heating radiators or under direct lines sun rays. This creates an excessive thermal load, forcing the motor to work at its limit.
The surface on which the equipment is placed must be perfectly flat and hard. If the floor is uneven, use the adjustable support feet located on the front bottom of the cabinet. Correct horizontal installation prevents vibration, noise and skewing of doors, which is especially important for two-chamber models with a system No Frost.
The importance of a temporary pause after transportation
One of the most critical points is the waiting time before turning on for the first time. When transporting the Indesit refrigerator, especially in a horizontal position, oil from the compressor could flow into the cooling system circuits. If you turn on the unit immediately, the oil that has not had time to drain back into the crankcase may clog the capillary tube or enter the combustion chamber, which will lead to hydraulic shock. The holding time depends on transportation conditions and ambient temperature. If the device was transported vertically and without strong shaking, 2-3 hours is enough. However, if water hammer.
The holding time depends on transportation conditions and ambient temperature. If the device was transported vertically and without strong shaking, 2-3 hours is enough. However, if refrigerator lying on your side or in the cold, the waiting period increases to 24 hours. This is necessary to completely stabilize the state of the refrigerant and lubricants.
In winter, when delivered in unheated transport, additional time is required for acclimatization indoors. Sudden changes in temperature can cause condensation to form on electrical components, causing short circuit hazards. Let the equipment warm up to room temperature before proceeding with electrical connection.
What will happen if you turn it on right away?
If you start the compressor with oil in the circuit, it can run dry, which will lead to jamming of the piston group. Repair in this case is often not economically feasible.
Hygienic treatment of internal chambers
Before loading products, new Indesit must be thoroughly washed. During production and storage, dust, factory grease or foreign odors may have settled on the shelves and walls. The use of aggressive chemicals is prohibited, as it can damage plastic elements or leave toxic traces.
To clean, use a warm solution of baking soda or mild soap. Thoroughly wipe down all surfaces, including door seals and crisper drawers. Pay special attention to corners and joints where dirt can accumulate. After washing, be sure to wipe all parts dry with a soft cloth.
Leave the doors open for a while to dry completely and remove odors. Moisture inside the chambers is unacceptable before switching on, as it can quickly turn into ice and disrupt the operation of the system automatic defrosting. Cleanliness inside is the key to the absence of bacteria and unpleasant taste in products.
☑️ Preparation for the first launch
The process of first connecting to the power supply
When all the preparatory stages have been completed, you can begin connecting. Make sure that the outlet meets the power and grounding requirements. Indesit refrigerators are sensitive to voltage surges, so it is not recommended to use extension cords or tees. Direct connection to a separate outlet is the safest option.
Insert the plug into the outlet. In modern models with electronic control, a sound signal sounds and an indication lights up on the display. In mechanical models, you will hear a characteristic click of the thermostat and the hum of the engine starting. The first minutes of operation may be accompanied by gurgling sounds - this is normal, as refrigerant begins to circulate through the system.
Do not load products into the chambers immediately. An empty refrigerator takes 2 to 4 hours to reach the required temperature. Loading warm products during this period will cause the compressor to work non-stop, trying to cool a large volume, which is stressful for the engine.
⚠️ Attention: If you hear a loud knock, crackling sound or smell a burning smell immediately after turning it on, immediately unplug the appliance. This may indicate a manufacturing defect or damage during transportation.
Setting temperature modes and functions
After the refrigerator has been idle for several hours, you need to adjust the temperature mode. In mechanically controlled models, this is done by turning a knob, usually located inside the refrigerator compartment. The recommended value to start with is 2 or 3 (on a scale from 1 to 5 or 1 to 7).
For devices with electronic control Indesit, the setting is made through the panel on the door. The optimal temperature for the refrigerator compartment is +4°C, and for the freezer - -18°C. You should not immediately set the minimum values, this will not speed up cooling, but will increase the load on the cooling system.
If your model is equipped with the function Fast Freeze (quick freezing), use it only when you need to freeze fresh food. In normal operation this function should be disabled to prevent the compressor from running continuously. Correct temperature calibration ensures the safety of vitamins in products and prevents the formation of excessive ice.
| Operating mode | Temperature (HC) | Temperature (MK) | Description |
|---|---|---|---|
| Eco / Standard | +4°C ... +5°C | -18°C | Recommended mode for daily use |
| Maximum cooling | +2°C | -24°C | For fast freezing large volumes of food |
| Holiday | +10°C ... +12°C | Off / On | Energy saving during long-term absence of owners |
| Super cooling | +2°C | -18°C | Short-term intensive cooling |
Remember that the temperature inside the chamber may change depending on the frequency of opening the doors and the amount of food. Thermostat automatically regulates the operation of the motor, maintaining the set parameters. You should not interfere with this process unnecessarily.
First loading with products and checking operation
4-6 hours after switching on, you can begin to gradually load fridge. Do not fill the chambers completely at once. Arrange the food so that there is space between it and the walls for air circulation. This is especially important for refrigerator models, where cold air is supplied through special channels. Check how the doors with food inside close. The seal should fit tightly around the entire perimeter. If the door moves away or does not fit completely, the cold will escape and the compressor will work in increased mode. Check No Frost, where cold air is supplied through special channels.
Check how doors with food inside close. The seal should fit tightly around the entire perimeter. If the door moves away or does not fit completely, the cold will escape and the compressor will work in increased mode. Check tightness with a sheet of paper: clamp it with the door and try to pull it out - it should come out with force.
On the first day of operation, observe the behavior of the device. It should not vibrate, rattle or make any extraneous sounds other than the uniform hum of the compressor and the noise of flowing refrigerant. If all parameters are normal, you can proceed to standard operation equipment.
Possible problems during the first startup
Even if all instructions are followed, nuances may arise. For example, the side walls may heat up - this is normal for modern models, where the capacitor is built into the sides of the case. Also, in the first hours, the fan may operate No Frost with periodic pauses.
If the refrigerator does not turn on, check the presence of voltage in the network and the integrity of the power cord. Sometimes the problem lies in a door that is not tightly closed, which is why the light does not come on and the engine does not start (in some models). Make sure that thermostat is not turned to the "Off" position.
⚠️ Attention: If within 2-3 hours of operation the temperatures in the chambers do not decrease and the motor runs continuously, there may be a freon leak or the compressor is faulty. In this case, you need to call a technician.
Timely identification of problems at the startup stage allows them to be resolved under warranty. Keep receipts and documents. The correct start is half the service life of yours Indesit.
How long can you not turn on the refrigerator after transportation?
The minimum waiting time is 2-3 hours if transportation was vertical. If the refrigerator was lying on its side or subjected to shaking, it is recommended to wait 12 to 24 hours for the oil to drain into the compressor.
Why does the refrigerator hum or click when you first turn it on?
The hum is the sound of the compressor running, and the clicks are the activation of the start relay or thermostat. The gurgling sound is caused by the movement of refrigerant. These are normal operating sounds if they are not accompanied by knocking or vibration.
Do you need to wash a new refrigerator before use?
Yes, definitely. Plastic particles, factory dust and odors may remain inside. Use a weak solution of soda or soap, then wipe dry thoroughly.
Is it possible to place the Indesit refrigerator close to the wall?
No, a gap of at least 5-10 cm is required for ventilation. The absence of a gap will lead to overheating of the condenser and increased energy consumption.