First launch of a Siemens electronically controlled refrigerator: instructions from A to Z

Electronic refrigerators Siemens with a touch or push-button control panel require correct first switching on - this is the key to long-term operation without failures. Even if you have already dealt with household appliances, the nuances of launching models iQ300, iQ500 or iQ700 may differ from classic mechanical analogues. In this article we will analyze not only the basic procedure, but also hidden settingswhich the manufacturer rarely mentions in paper instructions.

Errors during the first turn on are a common reason for calls to service centers. For example, Incorrect power connection sequence can lead to blocking of the compressor for 6-12 hours (the so-called “protective timeout”). And ignoring sensor calibration often causes incorrect temperature display. We will tell you how to avoid these and other problems.

Preparation before turning on: 5 mandatory steps

Before connecting the refrigerator Siemens to the outlet, check using the checklist. This will take 10-15 minutes, but will save hours of troubleshooting later.

Make sure the refrigerator has been standing upright for ≥4 hours (to stabilize the oil in the compressor)|

Check the voltage at the outlet (should be 220-240 V ±5%)|

Remove all shipping bolts and brackets (even if they are hidden under the rear panel)|

Inspect the rubber seals for damage|

Align the refrigerator (maximum permissible slope - 1°)

-->

Pay special attention transport bolts. In models Siemens KG39NXI35 or KG36NVI35 they can be hidden under decorative plugs on the back wall. If they are not removed, vibration of the compressor will lead to increased noise and the risk of damage to the refrigerant pipes. Use a 10 mm wrench - it is usually included in the kit.

Equally important leveling. Uneven installation leads to:

  • 🔹 uneven closing of doors (and as a result - freezing of the seal)
  • 🔹 increased load on the hinges (they can sag in 1-2 years)
  • 🔹 system malfunctions NoFrost (ice formation in the freezer)
⚠️ Attention: If the refrigerator was transported lying down (for example, in the trunk of a car), it must stand upright for at least 8 hours before turning it on. Otherwise, oil from the compressor will enter the refrigerant circuit, which will lead to breakdown in 1-3 months.

Where is the power button: search for the control panel

Depending on the model Siemens the control panel may located:

  • 📍 On top inside the fridge compartment (series iQ300, for example, KG33NVI30)
  • 📍 On the outer top of the door (series iQ500 and iQ700, for example, KG39NXB35)
  • 📍 On the front side of the freezer (models with French Door, for example, KI87SAF30)

Externally, the panels are divided into three types:

  1. Touch - react to a light touch (models after 2018). Often have backlit symbols.
  2. Pushbutton —physical buttons with tactile pressing (budget series).
  3. Rotatable —temperature adjustment with a wheel (found in models with LowFrost).

If the panel does not respond to touches, check:

  • 🔌 Connection to the outlet (the power indicator should light green or blue).
  • 🔋 The presence of a child lock (Child Lock —usually activated by a long press on the button with a lock).
  • 🕒 Protective timeout after transportation (can last up to 12 hours).

Touch|

Push-button|

Rotary|

I don’t know how to determine-->

Step-by-step instructions: how to turn on a Siemens refrigerator

Follow the algorithm strictly in order. Skipping steps may lead to failure of the electronic unit.

  1. Connect. refrigerator to the outlet.

    Use a grounded outlet. If the house has old wiring, install RCD (residual current device) to 16 A. In models Siemens with an inverter compressor (iQ700), voltage surges may disable the control board.

  2. Activate the main power.

    Press and hold the button On/Off (or Power) for 3-5 seconds until the display lights up. In some models. (for example, KG36VVW35) switching on occurs automatically when connected to the network.

  3. Set the temperature mode.

    Standard settings:

    • 🥶 Refrigerator compartment: +4°C (optimal for storing most products).
    • ❄️ Freezer compartment: -18°C (recommended for long-term storage).

    To change the temperature, use the buttons +/– or touch arrows In models with TwinCooling (double-circuit). cooling) settings for each chamber are set separately.

  4. Activate additional functions (if necessary).

    Useful options:

    • 🍎 SuperCool — fast cooling (useful after loading a large number of products).
    • ❄️ SuperFrost — intensive freezing (reduces time freezing by 30%).
    • 🌿 VitaFresh — freshness zone for fruits/vegetables (available in models iQ500+).

  • Close the door and wait for the first cooling cycle.

    The compressor will start in 5-30 minutes (depending on the model). At this time:

    • 🔊 Possible fan noise (norm for systems NoFrost).
    • 💨 Light smell of plastic (will disappear in 1-2 days).
    ⚠️ Attention: If after switching on the display shows an error E1, E2 or F5, immediately disconnect the refrigerator from the network and check:
    • The sensors are connected correctly (the connector may have come off during transportation).
    • Closing the doors (in models with a magnetic reed switch, an error may occur if the seal is not tight).

    Temperature settings: optimal values for different zones

    Electronic refrigerators Siemens allow you to flexibly regulate the climate in each zone Here are the recommended parameters:

    Zone. refrigerator Recommended temperature What to store Features
    Top shelf +2…+4°C Ready meals, milk, yoghurts The warmest zone (suitable for short-term storage)
    Middle shelves +3…+5°C Cheeses, sausages, sauces Optimal for most products
    Zone VitaFresh (bottom drawer) 0…+1°C Meat, fish, herbs, berries High humidity (up to 90%) slows down wilting
    Door +5…+7°C Drinks, oil, eggs The most unstable zone (temperature fluctuates when opening)
    Freezer -18…-24°C Meat, processed foods, berries For quick freezing, use SuperFrost (-30°C)

    In models with electronic control the temperature is displayed on the display with an accuracy of 0.5°C. However, actual values may differ by ±1°C due to:

    • 🔄 Door opening frequency.
    • 🌡️ Room temperature (optimal +16…+32°C).
    • 📦 The degree of loading of the chambers (products work as heat accumulators).

    For calibrating sensors in refrigerators Siemens iQ700 is provided service. modeTo enter it:

    1. Press and hold the "SuperCool" and "VitaFresh" buttons for 10 seconds.

    2. The code "d01" will appear on the display - this means access to the settings of the refrigerator compartment sensor.
    

    3. Use the "+"/"–" buttons to set the correction (from -3 to +3).
    

    4. Save the settings by pressing "On/Off".

    Common mistakes and how to avoid them

    Even experienced users make mistakes when they first turn on. Here are the top 5 problems and their solutions:

    1. The refrigerator does not turn on, the display does not light up.

      Reasons:

      • 🔌 The socket or power cord is faulty (check with a multimeter).
      • 🔋 The overvoltage protection has tripped (wait 10 minutes and turn it on again).
      • 🛠️ The electronic unit is damaged (diagnostics required).

    2. The display flashes an error E1 or F2.

      This indicates a problem with the temperature sensor Solution:

      • Turn off the refrigerator for 1 minute, then turn it on again.
      • Check the tightness of the door closure (the product packaging may be interfering).
      • If the error repeats, the sensor needs to be replaced (contact service).

    3. The compressor runs without stopping.

      Possible reasons:

      • 🌡️ The temperature is set too low (set +4°C for the refrigerator compartment).
      • 🔥 The room temperature is high (move the refrigerator away from the stove or radiator).
      • 🚪 Frequent opening of the door (give the refrigerator 2-3 hours to stabilization).

  • Ice forms in the freezer compartment (in models with NoFrost).

    This is a malfunction of the defrosting system. Check:

    • 🔌 The functionality of the evaporator heater (defrosting for 24 hours is required).
    • 💧 The drain hole is clogged (clean the tube with wire).

    • The display shows the incorrect temperature.

      The sensor calibration may have gone wrong. Reset: 

      Press and hold "SuperCool" +. "SuperFrost" 15 seconds.

    ⚠️ Attention: If the refrigerator Siemens makes a loud knocking or grinding noise after turning on, immediately unplug it! This may indicate:
    • A foreign object has entered the fan NoFrost.
    • Failure of the compressor (characteristic “metallic” sound).

    Operation in this condition will lead to expensive repairs.

    Hidden functions: what is not written in the instructions

    The manufacturer does not always disclose all the capabilities of electronic refrigerators Siemens. Here are a few “tricks” that will make operation easier:

    • 🔄 Vacation mode (HolidayMode).

      Activated by pressing the button with a palm tree. The refrigerator maintains the temperature +15°C, saving up to 40% of electricity. Useful if you are leaving for 1–2 weeks.

    • 📅 Sleep timer.

      In models iQ500 and above, you can program automatic shutdown after 1–12 hours (for example, for defrosting), set the time using the +/–buttons, then press Timer.

    • 🔇 Night mode (NightMode).

      Reduces the noise level to 38 dB by limiting the fan power. Turned on by long pressing the button with the moon.

    • 🔒 Child lock with PIN code.

      In refrigerators iQ700 you can set a 4-digit code: 

      1. Press "Child Lock" for 5 seconds.

      2. Enter the combination (default 0000).
      

      3. Set a new PIN.

    • 📊 Error log.

      The service menu (d05) stores the history of the last 10 failures. Useful for diagnostics before a technician's visit.

    How to reset a Siemens refrigerator to factory settings?

    For a complete reset:

    1. Unplug the refrigerator for 1 minute.

    2. Press and hold the "SuperCool" + "SuperFrost" + "On/Off" buttons simultaneously for 10 seconds.

    3. After "rSt" appears on the display, release the buttons.

    ⚠️ Attention: resetting will delete all user settings, including temperature profiles and timers!

    What to do if the refrigerator does not turn on after transportation

    If the refrigerator Siemens does not respond to clicks after delivery, the reasons may be the following:

    Symptom Possible cause Solution
    The display does not light up, there are no sounds Power surge protection has tripped Wait 10-15 minutes and turn on again
    The red indicator is on, beeping The door is not closed or the sensor has failed Check seal, restart the refrigerator
    The compressor hums, but does not start The compressor is jammed after horizontal transportation Turn off for 6-8 hours, then turn on again
    Error flashing E3 Problem with the fan NoFrost Defrost the refrigerator for 24 hours

    If the refrigerator was transported in a lying position, oil from the compressor could get into the circuit. refrigerantIn this case:

    1. Leave the refrigerator in an upright position for 8–12 hours.
    2. Connect to the power supply and try to turn it on.
    3. If the compressor does not start, do not try to turn it on again. This may lead to hydraulic shock i! breakdown.
    ⚠️ Attention: If after transportation the refrigerator Siemens turns on, but after 1-2 minutes it turns off with an error F1, this indicates malfunction of the electronic unit. - flashing or replacement of the board is required.

    FAQ: answers to frequently asked questions

    Is it possible to turn on the Siemens refrigerator immediately after delivery?

    No. If the refrigerator was transported vertically, wait. If horizontally - 4 hours. If horizontal - 8–12 hoursThis is necessary to stabilize the oil in the compressor and the refrigerant. Ignoring this rule. leads to breakdown in 1–3 months.

    Why, after turning on, the Siemens refrigerator does not cool, but only hums?

    Probable reasons:

    • 🔌 Temperature sensor is not connected correctly (check the connectors on the back wall).
    • 🧊 Capillary tube clogged (professional cleaning required).
    • ⚡ Compressor start relay faulty (needs replacement).

    If the refrigerator is new, contact the service under warranty. Self-repair will void the warranty.

    How to turn off the sound signal in a Siemens refrigerator?

    In most models, the signal is turned off as follows: 

    1 Press and hold the "Alarm" (or "Signal") button 3. seconds.

    2. A bell icon with a strikethrough will appear on the display.

    In series iQ700 you can adjust the alarm threshold (for example, only when the door is open >2 minutes).

    What does the error mean? E4 on the display?

    Error E4 indicates problem with the defrosting system NoFrostCauses:

    • 🔥 The heater has burned out. evaporator.
    • 💧 The drainage hole is frozen.
    • 📡 The defrosting sensor is faulty.

    Try defrosting the refrigerator for 24 hours. If the error repeats, parts need to be replaced.

    Is it necessary? defrost a Siemens refrigerator with the NoFrost system?

    Yes, but less often - 1 time every 12-18 months.. Despite automatic defrosting, dust and germs accumulate in the drainage system. To defrost:

    1. Unplug the refrigerator.
    2. Remove all food.
    3. Leave the doors open for 12-24 hours.
    4. Wipe the interior surfaces with a solution of vinegar (1:1 with water).

    Do not use sharp objects to remove ice - this will damage evaporator!

    • 📖 Read Also

    How to hang the door on the Indesit refrigerator: step-by-step instructions Detailed instructions on how to hang the door of the Indesit refrigerator to the other side. Loop diagrams, us How long should the refrigerator operate when first turned on Find out how long the refrigerator operates when first started. Norms for setting the temperature, especially How to turn on the Atlant refrigerator: step-by-step instructions and tips Detailed guide to starting the Atlant refrigerator for the first time: from unpacking to setting the temperature How to move the refrigerator without damaging the linoleum: step-by-step instructions A detailed guide on how to safely move a heavy refrigerator on linoleum. Effective methods, choice How to transport a refrigerator over a long distance: complete instructions Proper transportation of a refrigerator: how to pack, secure and defrost equipment. Tips for transpo How to hang a door on a built-in refrigerator: step-by-step instructions Detailed guide on installing a door on a built-in refrigerator: tools, fasteners, common mistakes