After purchasing and transporting household appliances, owners are often faced with the need for a correct first start-up. The question of how to turn on Ariston refrigerators does not arise by chance, because the durability of the compressor and the quality of freezing products depend on compliance with the sequence of actions. Ignoring basic transportation rules can lead to serious damage in the first weeks of operation.
Modern models Ariston are equipped with complex electronic control systems that require careful handling when activated. Simply connecting the plug to a socket is not enough for the unit to operate correctly, especially if the device was transported in a horizontal position. It is necessary to give the oil in the compressor time to drain into the crankcase to avoid water hammer at start-up.
In this article we will analyze in detail all the stages of preparing equipment for operation, setting temperature conditions and activating additional functions. You'll learn why it's important to wait a certain amount of time before turning it on and how to set it up correctly electronic control unit for maximum energy efficiency. Following these recommendations will allow you to avoid common mistakes made by beginners.
Preparation of the refrigerator after transportation
The first and most critical stage is the correct conditioning of the device after delivery. If the refrigerator was transported in an upright position, it is enough to wait 2-3 hours before inserting the plug into the network. However, during horizontal transportation, oil from the compressor could flow into the evaporator pipe system, and it takes time to return to its original position.
Service center specialists recommend keeping the unit in a warm room for at least 8 hours, and in winter - up to 24 hours. A sudden change in temperature when brought in from frost can lead to the formation of condensation on electronic boards, which will cause a short circuit. Therefore acclimatization equipment in room conditions is a prerequisite.
Before connecting, it is necessary to remove all transport elements. This applies not only to the external packaging, but also to the internal fasteners of shelves, drawers and adhesive tape on door seals. Parts left inside may prevent normal air circulation or damage glass shelves due to vibration during operation.
⚠️ Attention: Do not turn on the refrigerator immediately after unpacking if it has been in the cold. Let it warm up to room temperature for 4-6 hours to avoid failure of electronic components.
Check the integrity of the case and the condition of the sealing rubber bands. There should be no creases or cracks on them, as this directly affects the tightness of the chamber. Any defects at an early stage may be invisible, but over time they will lead to the formation of ice and increased load on the compressor.
First connection to the power supply
For connection, use only a working socket with grounding. The power of the refrigerator is relatively small, but the starting currents of the compressor can be significant. The use of extension cords or tees is not recommended, as poor contact at the connection point can cause heating and melting of the insulation.
After you insert the plug into the outlet, many models Ariston do not make any sounds immediately. This is normal as modern inverter compressors can start smoothly. However, it is worth listening: after a few minutes you should hear a quiet hum of a running motor, indicating the beginning of refrigerant circulation refrigerant circulation.
Pay attention to the control panel. If it lights up, it means power is supplied correctly. In some cases, it may be necessary to activate the operating mode, especially if the device was in demo mode in the store. To do this, it is usually enough to press and hold a certain combination of buttons indicated in the instructions for a specific model.
It is important to ensure stable voltage in the network. Electrical surges can damage sensitive control electronics. If power outages often occur in your area, it makes sense to install a voltage stabilizer or at least a surge protector with surge protection.
Setting temperature conditions
After startup, the most important stage begins - setting optimal operating parameters. By default, the factory settings are often set to medium values, but for the first time it is better to set the temperature to a lower temperature to cool the camera faster. Then you can switch to normal mode.
For the refrigerator compartment, the optimal range is considered to be from +3 to +5 degrees Celsius. The temperature in the freezer should not exceed -18 degrees. These values ensure safe food storage and prevent bacterial growth. Adjustment is carried out through thermostat or an electronic panel.
In models with a system No Frost it is important to give time to equalize the temperature in all corners of the chamber. It may take several hours for the cold air to circulate. Do not load the chamber with products immediately - it is better to wait 2-3 hours until the empty refrigerator reaches operating mode.
☑️ Initial setting of the refrigerator
⚠️ Attention: Do not set the minimum possible temperature immediately after turning on. This will place excess load on the compressor. Start with medium values and reduce them gradually.
If you notice that the food in the back of the chamber is freezing, but on the contrary, it is getting warmer at the door, the air circulation may be impaired. Check that large objects are not blocking the ventilation openings. Uniform distribution refrigerant depends on the free space inside.
Use of electronic control and display
Modern refrigerators Ariston are often equipped with digital displays that display the current temperature and status work. Control can be touch or push-button. To activate the panel, you may need to unlock it to prevent accidental changes in the setting by children or when cleaning.
Usually, to unlock, you need to press and hold the button with the image of a lock for 3-5 seconds. After this, the indicator will light up, indicating that you are ready to enter commands. If the panel does not respond, check whether the energy saving mode or demo mode is turned on.
The display may show various symbols indicating the operation of specific zones. For example, a snowflake means a freezer, and a drop means a refrigerator. Understanding these symbols will help you quickly navigate the settings and quickly respond to changes in the operation of the device.
What does the flashing temperature indicator mean?
If the temperature indicator is flashing, this is an alarm. It indicates that the temperature in the chamber is above the established norm. This can happen when you turn it on for the first time, after loading a large amount of warm food, or when the door is not tightly closed. If the flashing does not stop after a few hours, check the tightness of the seal and the operation of the compressor.
Some models allow you to configure individual zones, for example, a freshness zone or a zero chamber. Here the temperature can be around 0 degrees, which is ideal for storing meat and fish before cooking. Activation of these zones requires a separate approach and more accurate calibration temperature sensors.
Table of standard temperature zones
For the convenience of users, we provide a table with recommended settings for various types of products. Compliance with these parameters will help keep food fresh for as long as possible.
| Storage area | Recommended temperature | Type of food | Shelf life |
|---|---|---|---|
| Freezer compartment | -18°C and below | Meat, fish, semi-finished products | Up to 12 months |
| Bottom shelf of the refrigerator | +2...+4°C | Raw meat, fish, milk | 1-3 days |
| Middle shelves | +4...+6°C | Ready meals, sausages, cheese | 3-5 days |
| Door shelves | +6...+8°C | Sauces, drinks, eggs | Depends on the product |
| Freshness zone (Zero Zone) | 0...+1°C | Chilled meat, fish | Up to 7 days |
Using the correct storage areas allows you not only to extend the shelf life of products, but also to save energy. When you place food in the appropriate zone, the refrigerator requires less effort to maintain the desired climate. This reduces wear compressor group.
It is worth noting that the location of the zones may differ depending on the model. In some refrigerators, the freshness zone is located in a separate drawer, in others it is simply the lower part of the main chamber. Study the instructions for your Aristonto know exactly the architecture of the internal space.
Typical problems during the first start
Even if turned on correctly, users may encounter unusual phenomena. For example, the sides of a refrigerator may become hot. This is not a malfunction, but the normal operation of the condenser, which is often built into the side panels of modern models to remove heat.
Another common question is the gurgling or noise of water inside. This is the sound of circulating refrigerant as it flows from one part of the system to another. In models with No Frost system you can also hear plastic cracking when the temperature changes, which is caused by thermal expansion of materials.
If the refrigerator does not freeze after several hours of operation, check that the doors are tightly closed. Even a small gap will not allow the unit to reach the desired temperature, and the compressor will work continuously, trying to compensate for the cold leak. Also make sure that the device is level and the doors close under their own weight.
⚠️ Attention: If you hear a loud knocking, grinding noise or smell a burning smell, immediately unplug the device. These symptoms indicate a mechanical or electrical problem that requires professional attention.
In rare cases, a factory reset may be necessary. To do this, a combination of buttons or a special menu item is usually used. This helps eliminate software glitches if the electronics go haywire during a power surge. After the reset, the initial setup procedure will have to be repeated.
Frequently asked questions (FAQ)
How long can the refrigerator be turned on after delivery?
The waiting time depends on the method of transportation. If the refrigerator was transported vertically, 2-3 hours is enough. If in a horizontal position, you need to wait at least 8 hours, or better yet a day, for the oil to drain into the compressor.
Why does the Ariston refrigerator hum loudly when first turned on?
The first start-up is always noisier, since the system needs to create pressure and cool a large volume of air. The refrigerant passing through the pipes can also make noise. If the humming does not subside after a day or is accompanied by vibration of the case, check the adjustment of the legs.
Is it possible to immediately load food after turning it on?
No, it is not recommended. The refrigerator must run empty for 2-4 hours to reach the set temperature. Loading warm products will immediately create excess load on the compressor and can lead to damage to the products themselves.
What to do if the control panel does not light up?
Check for voltage in the outlet using another device. Make sure the plug is inserted all the way. If there is power, but the panel is silent, the protection may have tripped or the control unit is faulty - in this case, you need to call a specialist.
Do you need to defrost a new refrigerator before using it for the first time?
You do not need to defrost a new refrigerator, since it does not contain ice. However, it must be thoroughly washed inside with warm water and a mild detergent to remove the smell of new plastic and factory dust.
The correct first start is the key to the long service life of your equipment. By following these recommendations, you will ensure stable operation refrigeration equipment for many years. Remember that careful treatment of equipment in the first days of operation determines the service life of its operation in the future.