Refrigerator owners Bosch often face the need to reinstall or replace plastic boxes for vegetables, fruits and other products. This procedure seems simple only at first glance: improper installation can lead to distortions, difficulty closing the door, or even breakage of the guides. In this article we will look at how to properly insert drawers into refrigerators Bosch of different series, taking into account the features of their design.
The main difficulty lies in the variety of models. For example, in the KGE39AW20R series, drawers with side locks are used, and in KGN39VL35R - with a rear latch. We will describe both options in detail, as well as provide recommendations for selecting replacement parts if the original boxes are lost or damaged. We will pay special attention to models with a system VitaFreshwhere the drawers have additional seals to maintain humidity.
Preparation for installation: what you need to check before installation
Before you begin installation, make sure that you have all the necessary parts and tools. In most cases, only the drawers themselves are sufficient, but for some models (for example, Bosch KAN92VI45R), additional fastenings or gaskets may be required.
Pay special attention to:
- 📏 Drawer sizes. Even visually identical containers from different series may differ by 1-2 mm, which will make their installation impossible. Check the article numbers on the sticker inside the refrigerator with the catalog numbers of the drawers.
- 🔧 Condition of the guides. If the plastic rails are bent or clogged with dirt, the drawers will stick. Clean them with a damp cloth and check for cracks.
- 🧲 Magnetic seals. In models with NoFrost (for example, Bosch KGN39XW25R), drawers may have magnetic strips for a tight fit to the walls.
If you install drawers after defrosting or general cleaning, wait until the inner walls of the refrigerator are completely will dry out. Condensation on the plastic can cause slipping and improper fixation.
Types of fastenings for drawers in Bosch refrigerators
The design of the fastenings depends on the series and year of manufacture of the refrigerator. We have identified three main types that cover 90% of the model range Bosch:
| Mounting type | Refrigerator series | Installation features |
|---|---|---|
| Side grooves | KGE39, KGN36, KAN58 | Drawers are inserted into grooves on the sides walls and are fixed by pressure. Even pressure on both sides is required. |
| Rear latch | KGN39V, KAD92, KAN92 | On the back wall of the box there is a plastic hook that clings to the rail. You need to first wind up the back, then lower the front. |
| Magnetic latches | KGN39XW, KGE39AW (with VitaFresh) | Additional magnets on the bottom of the box ensure a tight fit. Accurate alignment is required. |
In refrigerators with a system VitaFresh Pro (for example, Bosch KAN92VI45R) the drawers may have double guides top ones for fixing the lid and bottom ones for the container itself. In this case, the lower part is installed first, then the top cover with a humidity regulator.
Step-by-step instructions: how to insert drawers with side grooves
This type of fastening is most common in budget and mid-price models Bosch. Follow the algorithm:
Take the box out of the packaging and check the integrity of the side recesses (they should be symmetrical).
Tilt the box at an angle of 30-45° so that its front part is lower than the back.
Place the back part of the box into the grooves on the side walls of the refrigerator. You should hear a slight click.
Lower the front of the drawer until it stops. If you feel resistance, do not press with force - remove the drawer and try again.
For models with telescopic guides (for example, Bosch KGE39AW20R) the process is slightly different:
Extend the guides to the maximum length|Wind the rear part of the drawer into the grooves|Smoothly push the guides until they click|Check the free movement of the drawer-->
If the drawer does not lock, check:
- 🔍 The presence of foreign objects in the grooves (crumbs, ice, plastic debris).
- 📐 Symmetrical installation - the drawer must be positioned strictly parallel to the walls of the refrigerator.
- 🛠️ The integrity of the plastic latches on the drawer itself (they can break if removed carelessly).
What to do if the drawer gets stuck in the middle?
If the drawer gets stuck when being pulled out, it is most likely deformed telescopic guides. Try lubricating them with silicone grease (do not use oils!). If this does not help, you will need to replace the guides - their part numbers are usually indicated in the instructions for the refrigerator.
Installing drawers with a rear latch: nuances and errors
Models with rear latch (for example, Bosch KGN39VL35R) require a more careful approach. The main mistake users make is trying to insert the box horizontally, which leads to breakage of the plastic hook.
Correct algorithm:
Lift the box so that its back wall is 5-7 cm higher than the front.
Place the back of the box under the top shelf of the refrigerator, hooking the hook to the metal rail.
Smoothly lower the front part until the drawer rests on the lower guides.
Press the front wall of the drawer until you hear a characteristic click (this means the latch has latched).
⚠️ Attention: If you hear a grinding or cracking sound when pressing the drawer, immediately stop installation. This is a sign that the hook is not in the groove and may break. Remove the drawer and try again.
In refrigerators with a system NoFrost rear latches are often combined with magnetic seals. In this case, after fixing the hook, make sure that the magnetic strips on the sides of the box fit snugly against the walls. If there is a gap of more than 2 mm between the drawer and the wall, check that the seal is installed correctly.
Features of installing drawers in models with VitaFresh
The system VitaFresh involves the use of special drawers with controlled humidity. Their installation has several key differences:
1. Double guides. The lower pair secures the box itself, the upper pair secures the removable lid with a humidity regulator. First, the lower part is installed, then the cover is put on it.
2. Sealing rubber bands. There are silicone seals around the perimeter of the box that should not twist. Before installation, straighten them with your hands.
3. Humidity regulator. In models Bosch KAN92VI45R and KAD92SB35R there is a slider on the box lid for adjusting the humidity. After installation, check its functionality by moving left and right.
For drawers VitaFresh It is strictly not recommended:
- 🚫 Using abrasive detergents - they will damage seals.
- 🚫 Placing boxes without a lid will disrupt the microclimate inside.
- 🚫 Use force when closing the lid - it should lower smoothly.
Common problems and their solutions
Even when following the instructions, users encounter typical difficulties. We have collected the most common of them and ways to eliminate them:
| Problem | Possible cause | Solution |
|---|---|---|
| The drawer does not lock, falls out when the door is opened | Broken back latch or guides are worn | Replace the latch (the article number is usually indicated in the instructions) or the entire guide |
| The drawer sticks when pulled out | Deformation of the telescopic rails or debris ingress | Clean and lubricate the guides silicone grease. If deformed, replace. |
| Gaps between the drawer and the walls of the refrigerator | Incorrect installation or wear of the seals | Reinstall the drawer, check the seals. If worn, replace. |
| Creak when the drawer moves | Lack of lubrication or friction of plastic on metal | Apply food-grade silicone grease to the guides. |
If your refrigerator Bosch equipped with an electronic display (for example, series models KAD92SB35R), after installing the boxes an error may appear E24 or E25. This is due to temperature sensors, which can be triggered when internal elements are displaced. In this case:
Unplug the refrigerator for 1-2 minutes.
Check whether the drawers are blocking the ventilation holes.
Turn on the refrigerator again. If the error recurs, diagnostics of the sensors is required.
⚠️ Attention: In refrigerators with inverter compressors (series Bosch KGE39AW20R and newer), it is not recommended to turn off the power more than once every 24 hours. This may cause the electronic unit to malfunction.
Where to buy replacement boxes and how to choose the right ones
If the original boxes are lost or damaged, they can be replaced. The main thing is to choose the right analogues. Here are the main methods:
- 🛒 Official Bosch dealers. The most reliable option, but often the most expensive. Article numbers of original boxes can be found in the instructions or on the manufacturer's website.
- 🌍 Online spare parts stores. Verified sites: Bosch Original Parts, eBay, AliExpress (for universal models). Always check the dimensions!
- 🔧 Universal drawers. Fits most models but may vary in depth. Example: drawers Universal Fit from Samsung or Electrolux are sometimes compatible with Bosch.
- 🔄 Used market. On Avito or Facebook Marketplace they often sell original boxes from disassembled refrigerators. Check the model series!
When choosing, pay attention to:
- 📏 Dimensions. Even if the boxes are visually similar, a difference of 5 mm will make them unsuitable.
- 🔍 Type of plastic. Original boxes Bosch are made of impact-resistant polypropylene (marking
PP). Cheap analogues can be made of PVC, which cracks in the cold. - 🧲 Presence of magnets/seals. For models with VitaFresh this is critical.
Average cost of original boxes for Bosch (for 2026):
- Standard box (without VitaFresh): 1,500–2,500 ₽.
- Box with VitaFresh: 3,000–4,500 ₽.
- Guides (set): 800–1,200 ₽.
⚠️ Prices and availability of spare parts may vary depending on the region and model of the refrigerator. For accurate information, check with authorized dealers or service centers Bosch.
FAQ: Answers to frequently asked questions
Can Bosch drawers be washed in the dishwasher?
No, this is strictly not recommended. High temperatures and aggressive detergents can deform the plastic and damage the seals. Wash the drawers only by hand with warm water (maximum 40°C) and a mild detergent.
Why does the new drawer not fit into the grooves, although the model is the same?
Possible reasons:
- The drawer is intended for another modification of the refrigerator (for example, for a model with NoFrost, and you have a drip system).
- The guides in the refrigerator are deformed or dirty.
- The drawer is installed at the wrong angle (especially important for models with a rear latch).
Try to clean the grooves and repeat the installation. If the problem persists, check the article numbers of the drawer and refrigerator.
How to remove the drawer if it is jammed?
Do not pull it by force - this may break the latches. Proceed as follows:
- Unplug the refrigerator.
- Tilt the drawer up (the back is higher than the front) and pull it towards you.
- If that doesn’t help, carefully pry it with a flat screwdriver on the side where the grooves are located.
- For models with using the rear latch, press the latch through the hole in the back wall of the drawer.
If the drawer is damaged and cannot be moved, contact the service center.
Can drawers from other brands be used in a Bosch refrigerator?
Theoretically, yes, but with reservations:
- Drawers must perfectly match in size (permissible deviation - no more than 1-2 mm).
- They must have a similar type of fastening (side grooves or rear latch).
- For models with VitaFresh only drawers with a similar adjustment system are suitable humidity.
Boxes from Siemens (same manufacturer) or Liebherr (similar technologies) are best suited. Before purchasing, check the dimensions!
What to do if, after installing the drawers, the refrigerator becomes louder?
This may be due to:
- Blocking of the ventilation holes (relevant for NoFrost).
- Friction of the drawers against the walls of the refrigerator (check the symmetry of the installation).
- By shifting the temperature sensors (in this case, an error may appear on the display).
Turn off the refrigerator, check the location of the drawers and ventilation grilles. If the noise does not disappear, contact the service.