Many owners of household appliances are faced with confusion after purchasing or general cleaning, when it comes time to return the interior of the refrigerator to its original state. Freezer compartment Beko refrigerators are designed with ergonomics in mind, but intuitive assembly is not always obvious at first glance. Incorrect installation plastic containers can lead to deformation of the guides or damage to the box itself during subsequent use.
In this article we will analyze the installation process in detail, paying special attention to the design features of various models Beko. You'll learn how to properly orient the skids, engage the latches, and distribute the load. Proper assembly will ensure durability mechanisms and tightness of the door closure, which is critical for energy efficiency.
Before starting physical actions, it is necessary to prepare the workspace. Make sure all parts are clean, dry and free of cracks. Inspecting the Components Checking for defects is an often-overlooked first step, but it is the first step that can help you avoid problems in the future. If you have just defrosted the unit, allow it to dry completely.
⚠️ Warning: Never force the drawer into place unless it slides in smoothly. Excessive pressure can break the thin plastic slides, which will then need to be repaired with glue or replaced.
Preparing the freezer for assembly
The first stage is always a thorough preparation of the internal volume. Even if you did not completely defrost, ice build-up could have formed inside guides. In refrigerators Beko the NoFrost system minimizes the formation of ice, but in older models or with infrequent cleaning, ice may interfere with installation.
Carefully inspect the side walls of the chamber. There are special grooves or rails along which they will move containers. In some models these runners are part of the body, while in others they are removable plastic elements. If your guides are removable and were dismantled for washing, they must be installed first, before the insertion of the drawers.
Pay attention to horizon level. The refrigerator must stand level. If the unit is skewed, the drawers may warp during installation, creating a false sense of dimensional inconsistency. Check the adjustment feet and tighten them if necessary.
- 🧊 Make sure that the interior of the camera is completely dry and free of water residues.
- 🔍 Check the integrity of the plastic slides on the side walls for chips.
- 🧹 Remove any foreign objects or packing tape that may have remained on the walls.
- ❄️ Make sure that the evaporator (back wall inside) is clean and not blocked by ice.
Cleanliness and dryness are the key to the box falling into place the first time. Ice chips caught in the sliding mechanism may prevent complete closure doors subsequently.
Design features of Beko drawers
Engineers Beko use several types of fastenings depending on the refrigerator series. Understanding which type you got will save time. Most often, there are systems with side guide rails and systems with front latches.
In classic models plastic box has special protrusions on the sides, which should fit into the grooves on the walls of the chamber. These projections are often in the form of hooks or rollers. In more modern series, such as Beko NeoFrost, a system of telescopic guides can be used, where the drawer extends completely, resting on metal or reinforced plastic rails.
Why may drawers of different levels differ?
Top drawers often have lower height and different shape of the front panel so as not to rest against the shelf of the upper refrigerator compartment or the door mechanism. Bottom drawers are usually deeper and more massive.
It is important to note that Front panel (front) of the drawer can be removable or integrated. If you have a model with removable fronts, make sure they are securely attached to the box itself before installing it in the chamber. Facade play may interfere with correct positioning.
| System type | Characteristics | What to pay attention to |
|---|---|---|
| Guide rails | Plastic runners on the walls | Coincidence of groove levels |
| Telescopic | Retractable metal/plastic. mechanisms | Smooth operation, lubrication |
| Hanging (hooks) | The box hangs on hooks at the side | Integrity of the hooks |
Knowing the type of your system will help you avoid mistakes. For example, if you have telescopes, you should not try to insert the drawer directly into the camera, bypassing the guides.
Step-by-step installation of the bottom drawer
Installation should always begin with lower level. This is due to the fact that the bottom drawer is often the largest and serves as the basis for upper levels or glass divider shelves. Take the lower container with both hands by the side walls.
Bring the box to the camera and tilt its front part slightly up, if required by the design of the runners. In models Beko with classic rails, you must first insert the back of the drawer into the deep grooves, and then lower the front so that it rests on the front supports. The movement should be progressive and soft.
☑️ Algorithm for installing the bottom drawer
After the box has rested on the supports, try to pull it out. It should move smoothly, without jerking or distortion. If you hear a grinding noise, it means guides did not match. In this case, the drawer must be lifted and the procedure repeated.
⚠️ Attention: When installing the lower drawer, make sure that it does not touch the cooling system pipes if they are located below (in older models without NoFrost). Damage to the freon pipes will lead to expensive repairs.
Installation of middle and upper containers
After successful installation of the bottom, we proceed to middle level. A nuance with a glass lid often arises here. In many refrigerators Beko the upper surface of the lower drawer or a special glass shelf is the “ceiling” for the lower container and the “floor” for the middle one.
If your model has a glass partition between the tiers, install it first. It rests on special protrusions on the side walls or on the sides of the bottom drawer. After making sure that the glass sits tightly and horizontally, proceed to install the next container.
The installation technique is similar to the bottom one: start it, lower it, check it. However, it is important to control the height here. Top drawer It should not rest against the door or ceiling of the freezer when closing. Sometimes it is necessary to adjust the height of the legs of the refrigerator itself if the top drawer touches the seal.
- 📏 Check that the glass shelf-separator lies flat and does not wobble.
- 👐 Hold the drawer when pushing it in so that it does not slide back under its own weight.
- 👁️ Visually assess the gap between the box lid and the top of the chamber.
- 🔊 Listen: the absence of squeaking indicates correct installation.
Pay special attention to the top drawer. It is he who most often comes into contact with the mechanism doors. If the drawer is too high, it will interfere with tight closing, which will lead to freezing of the “fur coat” and increased energy consumption.
Adjusting and checking the operation of the mechanism
The final stage is a comprehensive check. After everything containers is installed, you need to open and close the freezer door several times. Movement should be free, without resistance from the drawers.
Pull out each drawer to its maximum depth. In models Beko with a stop system, the drawer should not fall out completely, even if it is pulled out all the way. Check the operation of the locking mechanisms (if any) by slightly lifting the front edge of the drawer as it slides out - this is the standard unlocking procedure for complete removal.
If you notice misalignment, do not ignore it. A skewed box will deform itself over time and can damage neighboring elements. In such cases, it is worth checking whether packaging film or a piece of ice has gotten under the guides.
Common mistakes and how to avoid them
One of the most common mistakes is trying to push the box by force. Users often do not notice that they are trying to insert it upside down or backwards. Plastic At low temperatures it becomes brittle, and one wrong movement can lead to a crack.
Another mistake is ignoring the load level when checking. An empty box can move easily, but if you overdo it with food, the mechanism can jam. Always leave a small amount of free play. Also, you should not install drawers in a refrigerator that has not yet dried after washing.
⚠️ Attention: The design of refrigerators may vary slightly depending on the year of manufacture and the specific model. Always check the official manufacturer's instructions for your Beko range if standard methods do not work.
Avoid using harsh chemicals to clean drawers before installation. Residues of detergents can make the plastic slippery or, conversely, sticky, which will disrupt the operation of the sliding mechanism.
FAQ: Frequently asked questions
Why does the top drawer not close all the way?
Most likely, the drawer is installed too high or skewed. Check that it fits correctly on the guides. Also make sure that the food inside does not interfere with the closure or rest against the lid.
Can the drawers be washed in the dishwasher?
Most plastic containers Beko are made of frost-resistant plastic that can withstand high temperatures. However, frequent washing in the dishwasher on the dry cycle can make the plastic more brittle over time. It is better to wash it by hand with warm water.
What to do if the runner guide is broken?
If the guide is plastic and breaks off, you can try to glue it with a special glue for plastic, but this is a temporary solution. For durability, it is better to order an original spare part for the refrigerator model.
How to remove the drawer completely for washing?
Pull out the drawer until it stops. Then lift the front of it slightly (usually 10-15 degrees). This will release the stoppers and the drawer can be removed from the guides.
Does incorrect installation of drawers affect the operation of the refrigerator?
Yes, if the drawer is skewed, it may prevent the door from closing tightly. This will lead to loss of cold, the formation of ice and increased load on the compressor, which will shorten the service life of the unit unit.