Buying a new refrigerator is always a joyful event that promises comfort and safety of food. However, for brand equipment Indesit to serve for many years without failures, it is not enough to simply plug the cord into an outlet. There are critically important technical nuances, which, if ignored, can lead to compressor failure or system leakage.
Many users make the mistake of starting operation immediately after unpacking, not allowing the oil to drain into the crankcase or not equalizing the temperature of the unit. In this article, we will look in detail at how to properly launch your new Indesit refrigeratorto avoid costly repairs in the future.
You have to go through several stages: from correct installation of the case to the first setting of the thermostat. Compliance with the sequence of actions ensures that the device reaches operating mode without unnecessary load on the engine.
Transportation and waiting time before switching on
The most important stage, which is often ignored, is the time the equipment rests after delivery. If the refrigerator was transported in a horizontal position or tilted strongly, compressor oil could get into the cooling system circuits. An instant start in this state will lead to water hammer and failure of the discharge valve.
The time that must be waited directly depends on how exactly the transportation was carried out. If the device was standing vertically and the angle of inclination did not exceed 40 degrees, it is enough to let it stand for 2-3 hours in a warm room. This is necessary to stabilize the temperature of the internal components after frost.
⚠️ Attention: If the refrigerator was lying during transportation, the waiting time should be at least 8, and preferably 12 hours. This is critical for the oil to flow back into the compressor.
It is also worth considering the temperature difference. Bringing equipment from the cold into a warm apartment causes condensation to form inside the electronic boards and on the electrical contacts. Turning on a wet appliance may cause a short circuit.
Some models Indesit are equipped with complex electronics, which are also sensitive to changes in temperature and humidity. Allow the device to fully acclimatize.
- 🕒 For vertical transportation, wait 3-4 hours.
- 🛌 For horizontal transportation - at least 8-12 hours.
- ❄️ When bringing in from frost - until the condensate dries completely (up to 24 hours).
- 🌡️ Make sure that the room temperature is above +10°C.
Installation and preparation of the location
Before connecting the power cable, you must install the case correctly. The refrigerator Indesit must stand on a flat, hard surface. Misalignments can lead to improper operation of the doors, vibration noise from the compressor, and even problems with the circulation of refrigerant in the system. No Frost.
Use adjustable feet at the front of the unit. Rotate the legs until the body leans slightly back. This will ensure that the doors automatically close under the influence of gravity, which is important for maintaining tightness.
It is important to provide sufficient clearance for ventilation. The heat exchanger, located on the back wall or on the sides (depending on the model), must freely release heat to the environment. Lack of clearance will lead to overheating of the compressor and increased energy consumption.
td>Ideal
| Installation parameter | Recommended value | Consequences of violation |
|---|---|---|
| Rear gap | Minimum 5-7 cm | Overheating of the condenser |
| Gap on the side | Minimum 5 cm | Poor air circulation |
| Distance from slabs | At least 30 cm | Damage to the seal by heat |
| Floor evenness | Noise, vibration, knocking |
Do not install the refrigerator in niches without ventilation or close to kitchen cabinets, if this is not provided for in the design of built-in models. Heat must escape freely, otherwise thermostat it will give incorrect readings.
Primary treatment of internal chambers
The inside of a new refrigerator may have a specific technical smell of plastic and grease. It is recommended to carry out sanitization before loading products. This will not only eliminate odors, but will also wash away dust that has settled during storage in the warehouse.
Use a weak solution of baking soda or a mild detergent. It is strictly forbidden to use abrasive powders, chlorine-containing products or aggressive chemicals, as they can damage the plastic surface and antibacterial coating.
⚠️ Attention: Never wash the refrigerator with hot water. A sharp temperature change can cause microcracks in the internal plastic or damage to glass shelves.
After wet cleaning, thoroughly wipe all surfaces with a dry, clean cloth. Pay special attention to recesses and joints where moisture can accumulate. Leave the doors open for 1-2 hours for complete drying and ventilation.
☑️ Preparing the chambers for work
Make sure that all removable elements, such as shelves and drawers Crispare installed correctly and until they click. Loosely closed guides can become a source of noise when the fan operates.
First connection to the power supply
When the waiting time has passed and the cameras are prepared, you can begin the electrical connection. Refrigerators Indesit require a separate outlet with mandatory grounding. The use of extension cords or tees is not recommended, as compressor inrush currents can cause heating of the contacts and a fire.
Insert the plug into the socket tightly. At this moment, you may hear a quiet hum or feel a slight vibration of the body - this is normal, the engine starts. Modern models may not have a physical power button on the case; startup occurs automatically when power is applied.
If your model is equipped with an electronic display, it will light up immediately. In some cases, it may be necessary to activate the operating mode. To do this, find the power button (often indicated by a power symbol or inscription On/Off) and hold it for 3-5 seconds.
What to do if the refrigerator hums immediately after turning on?
Humming in the first minutes of operation is a normal process for the compressor to enter operating mode. If the sound does not change to knocking or clanging, there is no need to worry.
Pay attention to the indicators. Flashing lights can signal the process of entering the mode or, conversely, an error. The interpretation of the signals can always be found in the instructions for a specific model, for example, Indesit DS 320 or Indesit EF 18.
Setting the temperature mode and functions
After turning on the compressor, you must set the correct temperature. Factory settings may be average, but for the first launch it is better to set the average values so as not to overload the system. For a refrigeration chamber, the optimal range is considered to be from +3°C to +5°C.
In mechanical models, adjustment is carried out by turning the thermostat knob, usually located inside the chamber. Place the handle in the middle position (often marked 3 or 4). In models with electronic control, use the panel Control Panel to select exact values.
- 🌡️ For the refrigerator compartment: +4°C.
- ❄️ For the freezer compartment: -18°C.
- 🚀 Mode Super Freeze: turn on only when the load is heavy.
- 💡 Eco Mode: saves energy, but cools more slowly.
If your refrigerator has a function No Frost, do not be alarmed if the first cooling takes longer. The system should cool the entire volume evenly, including hard-to-reach corners. Do not open the doors frequently during the first hours of operation.
⚠️ Attention: Do not set the minimum temperature (maximum cold) immediately after switching on. This will force the compressor to work without stopping, which can lead to its overheating at the first start.
Time to reach operating mode and loading products
The most common mistake is loading products immediately after turning on. An empty refrigerator cools faster, but if you fill it with warm food right away, the load on unit increases many times over. The compressor will work hard, trying to cool a large volume of heat.
Let the refrigerator run idle for at least 2-4 hours. During this time, the temperature in all chambers will stabilize, and the system will automatically switch to standby mode (the compressor will turn off). Only after the first automatic engine stop can you start loading.
Load the products gradually. Do not place hot or warm dishes - this will disrupt the microclimate and force the equipment to work in emergency mode. Distribute food so that it does not block the ventilation openings, especially in systems Total No Frost.
Recommended loading order:1. Chilled drinks and ready meals.
2. Dairy products and meat (on the lower shelves).
3. Vegetables and fruits (in the bottom drawers).
4. Freezing (in the freezer if it has already gained cold).
It is recommended to make a full load within 24 hours, in small portions. This will allow the system to smoothly adapt to the thermal temperature.
Frequent questions when starting up for the first time (FAQ)
Why does the Indesit refrigerator get very hot on the sides when you first turn it on?
This is normal. In modern models, the condenser (heat exchanger) is often built into the side walls of the case. When the compressor is actively operating, they heat up, giving off heat. Over time, when the temperature inside stabilizes, the heating will decrease.
You hear the sound of gurgling or pouring water - is this normal?
Yes, this is the sound of refrigerant (freon) circulating through the system pipes. Newer refrigerators with lower noise levels may be able to hear these sounds more clearly. If there is no extraneous knocking of metal on metal, there is nothing to worry about.
How long should the compressor turn off for the first time?
The time of the first operating cycle depends on the temperature in the room and the volume of the chambers. Typically the first cycle lasts from 30 minutes to 2 hours. If the compressor runs for more than 4-5 hours without stopping when the refrigerator is empty, check the tightness of the doors.
Is it necessary to defrost a new refrigerator before use?
No, new refrigerators Indesit, even with manual defrosting, do not require defrosting before the first use, since they are new and dry. You just need to wipe them with a damp cloth for hygiene.