Rehanging the door of a two-chamber Ariston refrigerator: instructions with photos and videos

Re-hanging the refrigerator door Ariston is a task that many owners face when moving, renovating a kitchen, or simply wanting to change the opening side. The brand’s two-chamber models (series Hotpoint-Ariston, MBF, NBM etc.) structurally provide for this possibility, but the process requires accuracy and knowledge of key nuances. Unlike single-chamber refrigerators, here you will have to work with two doors, hinges of the upper and lower chambers, and also take into account the location of the freezer compartment.

Improper installation can lead to misalignment of doors, breakage of tightness or even breakage of fasteners. For example, if you do not adjust the opening limiter or forget to re-hang the decorative plugs, the door will close with force or leave gaps. This article contains step-by-step instructions taking into account the features of models Ariston of the last 10 years, a list of necessary tools and answers to typical questions.

⚠️ Important: If your refrigerator is under warranty, hanging the door yourself can void it. Check the conditions with the service center Ariston before starting work.

1. Preparation: tools and conditions

To hang the doors of a two-chamber refrigerator Ariston you will need:

• 🔧 Phillips and flat screwdrivers (preferably magnetic so as not to lose the screws)
• 🔨 Hex key (usually size 4 or 5 mm - depends on the model)
• 📏 Tape measure or ruler (for checking gaps)
• 🧲 Magnet or telescopic gripper (for removing fallen screws)
• 🧴 Silicone grease (optional, for hinges)

Before starting work be sure to unplug the refrigerator and defrost it if the freezer is covered with ice. The optimal room temperature is not lower than +18°C, so that plastic parts do not become brittle. Make sure you have a helper nearby: a refrigerator door weighs 8–12 kg, and a freezer door weighs up to 15 kg. Working alone is inconvenient and dangerous.

⚠️ Attention: If your refrigerator is equipped with a system No Frost or an electronic display on the door, before rehanging, take a photo of the location of the wires and connectors. Their accidental damage can damage the control module.

2. Design features of two-chamber models Ariston

Two-chamber refrigerators Ariston have two independent doors - for the refrigerator and freezer compartments - which are attached to four hinges (two on top and two on the bottom). Key differences from single-chamber models:

• 🔄 Middle hinge (if any) connects the two doors together and requires re-hanging separately.
• 🧊 The freezer door is often heavier due to insulation and may have an additional lock.
• 🔌 Electronic models (for example, Ariston MBA 2200) have wiring for the display or sensors - it cannot be pulled.

Most models have symmetrical hinges, but some series (for example, Hotpoint-Ariston HBM) have left- and right-side fastenings with different threads. In this case, you will have to buy an additional set of hinges for the other side (the article number is indicated in the instructions).

💡

3. Step-by-step instructions for re-hanging

Let's consider the process using the example of a model Ariston MBA 2200 (similar for most two-chamber refrigerators of the brand). The whole process will take 1–1.5 hours.

Step 1: Removing the top door (refrigerator compartment)

1. Remove the decorative plugs from the hinges (pry them off with a flat screwdriver).
2. Unscrew the screws of the top hinge (usually 2-3 pieces) and carefully hold the door.
3. Remove the door from the bottom hinge by pulling it up.

Step 2: Re-hanging the top hinge

1. Move the top hinge to the opposite side using the existing holes (they are covered with plugs).
2. Secure the hinge with screws, but do not tighten them completely - adjustment will be required.

Step 3: Working with the freezer door

1. Remove the middle hinge (connects the two doors) and move it to the other side.
2. Unscrew the bottom freezer hinge and rearrange symmetrically.
3. Install the freezer door on the new bottom hinge, then connect it to the refrigerator door through the middle hinge.

Step 4: Adjustment and check

1. Align the doors vertically and horizontally, tightening the hinge screws.
2. Check the tightness: place a sheet of paper between the seal and the body. If it falls out, additional adjustment is needed.

📋

4. Typical mistakes and how to avoid them

Even when following the instructions, many make mistakes that lead to problems in the future. Here are the most common ones:

• 🔩 Loose hinge screws → the door sags after a week of use.
• 🔄 Unmoved limiter opening → the door opens too wide and hits the wall.
• 🧲 Damaged seal → the refrigerator stops freezing, ice appears on the back wall.
• ⚡ Forgotten wires (in models with a display) → error E1 or E2 on the panel.

⚠️ Attention: If, after rehanging, the refrigerator begins to buzz or vibrate loudly, check whether the door is touching the housing. This may indicate hinge misalignment or incorrect installation of the middle fastening.

🔧

What to do if the door does not close tightly?

Check if something is in the way seal (for example, crumbs or dirt). Wipe the rubber band with soapy water. If the problem remains, tighten the screws on the top hinge or adjust the legs of the refrigerator.

5. Adjusting the doors after rehanging

After installing the doors on the new side, they need to be adjusted to ensure a tight fit and easy opening. Here are the key points:

Vertical adjustment

If the door sags or, conversely, lifts up:

1. Loosen the screws on the bottom hinge.
2. Lift or lower the door to the desired level.
3. Tighten the screws and check the movement.

Horizontal adjustment

If the door touches the body or moves too far away:

1. Tighten the screws upper and middle hinges (clockwise - closer to the body, counter - further).
2. Use a level to check the vertical.

📌

6. Models with a display: nuances of rehanging

Refrigerators Ariston with electronic control (for example, Ariston EBD 6181 or Hotpoint-Ariston H-FN 1811) have a display on the door, which is connected by wires to the main module. When rehanging, you need to:

1. Carefully disconnect the connectors (usually they are located under the top loop).
2. Move the wires to the other side without twisting them.
3. Make sure that the length of the wires is sufficient for the new position (in some models this is required extension cord).

⚠️ Attention: If, after rehanging, an error E4 or E5appears on the display, this means a problem with connecting the sensors. Immediately turn off the refrigerator and check the integrity of the wires.

📺

7. Care after re-hanging

After successfully re-hanging the doors, the refrigerator Ariston requires a little maintenance:

• 🧼 Wipe the sealing rubber bands with a mild soap solution —they could have traces of adjustment.
• 🛠️ Lubricate the hinges with silicone grease (do not use WD-40 - it corrodes the plastic!).
• 📏 Check the temperature in the chambers after 12 hours: if it is higher than normal, the seal may be broken.

If 1-2 days after rehanging you notice:

• 🌬️ Condensation accumulation on the walls - check the seal.
• ❄️ Icing of the freezer -leakage is possible cold.
• 🔊 Extraneous sounds when opening/closing - tighten the hinges.

Frequently asked questions (FAQ)

Is it possible hang the refrigerator door Ariston without an assistant?

Technically yes, but it is extremely inconvenient. The freezer door weighs 10–15 kg, and holding it with one hand while tightening the screws is almost impossible. The risk of dropping the door or damaging the hinges is very high. If there is no assistant, use carpenter's clamps to fix the door during operation.

What should you do if, after rehanging, the refrigerator began to operate loudly?

Most likely, the hinges shifted when adjusting compressor or the refrigerant pipes began to vibrate against the housing. Check:

1. Is the refrigerator level (use a level).
2. Are the tubes touching the back wall.
3. Are all hinge screws tightened.

If the noise persists - call a technician for diagnostics.

Is it necessary to defrost the refrigerator before rehanging it?

It is necessary if there is ice in the freezer. It adds weight to the door and can distort the hinges when removed. For models No Frost defrosting is not required, but it is still necessary to disconnect the refrigerator from the network during work.

Where can I get new hinges if the old ones do not fit on the other side?

Original hinges for Ariston can be ordered:

• In the official service center (by model number).
• On spare parts websites: r-style.ru, zapchasti-msk.ru (indicate the exact article number from the sticker on the refrigerator).
• In stores like “220 Volt” or “M-Video” (if the model popular).

The cost of a set of hinges is from 800 to 2500 rubles, depending on the model.

Is it possible to hang the door on the refrigerator Ariston with the system Total No Frost?

Yes, but with caution. In such models (for example, Ariston TMB 2551) there are often additional temperature sensors on the door. When rehanging:

1. Disconnect the sensor connectors (they are usually marked in red or blue).
2. Move the sensors to the new side without reversing the polarity.
3. Check the operation of the refrigerator for days - if an error appears E3, it means the sensor is connected incorrectly.