We rehang the Ariston Hotpoint refrigerator door with our own hands: instructions with photos and video

Re-hanging the refrigerator door Ariston Hotpoint is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Despite the apparent complexity, the procedure is quite doable at home if you know the key nuances of the design and avoid common mistakes. In this article we will analyze step-by-step algorithm for models with top and bottom hinges, pay attention to tools, and also reveal secrets that are not written in standard instructions.

It is important to understand that refrigerators Hotpoint-Ariston (especially releases after 2018) often have a unified door fastening system, but some series - for example HB 3800 or HBM 1182 - require an individual approach. We took these features into account and collected unique data on the location of mounting holes and the seal reinstallation diagramthat are not in the official manuals. If your model is equipped with a display or system No Frostpay attention to additional recommendations in the relevant sections.

Preparation: tools and safety

Before you start working, Make sure you have everything you need on hand. The absence of even one tool can lead to damage to plastic parts or thread breakage

• 🔧 Hex key (usually 5 or 6 mm - depends on the model). A special key is often included with the refrigerator.
• 🔨 Phillips screwdriver (PH2) and a flat key (for prying up decorative plugs).
• 📏 Level (to check the evenness of the door installation after rehanging).
• 🧲 Magnet or tape —to fix the door during operation and avoid falling.
• 🧴 Silicone grease (optional, for processing hinges after installation).

Also prepare your workspace: clear access to the refrigerator from all sides, unplug it (at least so that the cord does not get in the way), and place a soft cloth on the floor - this will protect the door covering from scratches when removing it. If your model has display on the door, take a photo of the wire connection in advance - this will save time during reassembly.

⚠️ Attention: On models with electronic control (for example, Hotpoint HBM 1382) after rehanging the door it may required resetting settings through the service menu. Otherwise, the temperature sensors will not work correctly. Details are in the section about setting up after installation.

Door fastening diagram: what you need to know before starting work

Design of hinges Ariston Hotpoint different from most budget refrigerators. Here dismountable hinges with eccentric bushingsare used, which allow you to adjust the height and tilt of the door. This is both a plus (you can accurately set the gaps) and a minus (if you remove it inaccurately, the bushings can fall out and get lost).

Typical fastening scheme:

• 🔄 Upper hinge —fixed with 2-3 bolts, often hidden under the decorative cover.
• 🔄 Lower hinge —may have an additional lock to stop the door when closed.
• 🔧 Middle loop (if any)—found in models with a height of 180 cm or more, requires synchronous loosening of both fastenings.
• 📐 Seal - attached to double-sided tape or groove, it will also have to be reinstalled.

If your model is not listed in the table, pay attention to hinge markings: they usually have arrows indicating the direction of opening. This will help you navigate when reinstalling. On some refrigerators (for example, series Hotpoint Aqualtis), the hinges are universal and are suitable for both sides, but require rearranging the bushings.

What to do if the bolts are “stuck”?

If the bolts do not unscrew due to oxidation, do not use excessive force as this may strip the threads. Instead:

1. Apply WD-40 or similar lubricant to the threads.

2. Wait 10–15 minutes.

3. Try unscrewing again, using a long-handled wrench for better leverage.

4. If it doesn’t help, carefully heat the hinge with a hairdryer (do not overheat the plastic!).

Step-by-step instructions: removing the old door

Start with the top hinge - this will simplify further work. Proceed according to the following algorithm:

1. Remove the decorative plugs from the hinges (pry them off with a flat screwdriver or knife). The bolts are hidden under them.

2. Loosen (but do not remove completely!) the upper hinge bolts by 2-3 turns. This will allow you to lift the door.

3. Holding the door with one hand, completely unscrew the top hinge bolts. Remove the hinge and set it aside.

4. Gently lift the door up to free it from the bottom hinge. If the door is “jammed,” check whether the seal or retainer is in the way.

5. Remove the door and place it on a soft surface (for example, a blanket).

On models with display before removing the door, you must disconnect the wires. To do this:

• 🔌 Find the connector on the refrigerator box (usually on the bottom right or left).
• 📱 Carefully press the latch and pull out the plug. Do not pull the wires!
• 🔄 Remember or take a photo of the connection order.

If your model has one middle hinge, it must be loosened before removing the door, but not completely removed - otherwise the door may warp. On refrigerators Hotpoint with system No Frost the middle hinge is often combined with the duct mount - be careful not to damage it.

⚠️ Attention: On models with automatic ice maker (for example, Ariston HBM 2052) additional water pipes are installed in the door. They should not be bent or twisted - this can lead to leaks. If you are not confident in your abilities, it is better to contact a specialist.

Moving the hinges and seal to the other side

After removing the door, it is necessary to transfer the hinges and seal to the opposite side. There are several critical points here:

1. Loops:

• 🔧 Move the upper and lower loops to the mirror holes. In most models, they are already provided and closed with plugs.
• 🔄 If there are no holes, you will have to drill them yourself (only for older models before 2015). Use a metal drill with a diameter of 4–5 mm.
• 📏 Check that the hinges are installed strictly symmetrical - otherwise the door will be warped.

2. Seal:

• 🧽 Remove the old seal by carefully prying it off with a screwdriver. Start from the top corner.
• 🧴 Clean the groove from any remaining glue or dust (you can use alcohol).
• 🔄 Install the seal on the new side, starting from the bottom corner. Make sure that it fits tightly around the entire perimeter.
• 🔥 For better fixation, heat the seal with a hairdryer (temperature 40–50°C) - this will make it more elastic.

On models with magnetic seal (for example, Hotpoint HBM 1384) rearrangement may require additional adjustment of the magnets. If after installation the door does not fit well, check the polarity of the magnets - they should be attracted to the body and not repelled.

Installing the door on the new side and adjusting

Now all that remains is to assemble everything in the reverse order. Here are the key steps:

1. Place the door onto the bottom hinge, holding it at the top edge.

2. Align the door vertically and secure the top hinge with bolts (do not tighten it all the way!).

3. Check that the gaps between the door and the body are the same all the way around (optimally - 2–3 mm).

4. Tighten the bolts crosswise to avoid distortion.

5. Install decorative plugs on the hinges.

After installation, check:

• 🔄 Ease of opening —the door should move smoothly, without squeaks.
• 🧲 Tightness - take a sheet of paper, close the door and try to pull it out. If the sheet comes out easily, the seal needs to be adjusted.
• 📏 Level —use a building level to make sure the door is not warped.

If the door opens spontaneously, this is a sign of incorrect adjustment of the hinges. In this case:

1. Loosen the bolts of the top hinge.
2. Adjust the position of the door by slightly tilting it forward (to do this, loosen or tighten the eccentric bushing).
3. Tighten the bolts and check again times.

Features for models with a display and No Frost

Refrigerators Ariston Hotpoint with electronic control and system No Frost require additional actions after re-hanging the door. Here's what you need to do:

1. Connecting the display:

• 🔌 Connect the wires to the connector on the refrigerator box, following the photographs taken earlier.
• 📱 Plug in the refrigerator and check if the display lights up. If not, check that the plug is secure.
• 🔄 If the display blinks or shows an error (for example, E1 or F0), reset the settings: press the buttons Mode and Temp + 5 seconds.

2. Setting up the No Frost system:

• ❄️ After rehanging the door, air circulation may be disrupted. Start forced defrosting: turn off the refrigerator for 1 hour, then turn it on again.
• 🌡️ Check the temperature in the freezer after 6-8 hours. If it is higher than normal, the air duct may be pinched (see the section on typical errors).

On models with ice maker (Ariston HBM 2052, Hotpoint HBM 1384) after rehanging the door, it may be necessary water sensor calibration. To do this:

1. Press and hold the button Ice 10 seconds.
2. Wait for the sound signal.
3. Run an ice cycle to check for tight connections.

⚠️ Attention: If the refrigerator begins to consume more power after re-hanging the door, check to see if the display cable or ice maker tubes are pinched. This may cause a short circuit or leakage of freon.

Typical mistakes and how to avoid them

Even with careful work, many encounter problems after re-hanging the door. Here are the most common errors and ways to eliminate them:

One of the most insidious mistakes is incorrect installation of eccentric bushings. If they are mixed up, the door will either hang loose or fit too tightly, which will lead to rapid wear of the seal. Bushings are usually marked with arrows or letters (L and R) - pay attention to this!

Another common problem is damage to the plastic plugs when removing. If they are cracked, do not try to install them back: over time, the plugs will begin to fall off, exposing the bolts. It is better to buy spare ones in advance (the article number is usually indicated in the instructions for the refrigerator).

What to do if, after rehanging, the door “moves away” over time?

This occurs due to the weakening of the eccentric bushings. Solution:

1. Remove the decorative plugs.

2. Tighten the hinge bolts (but do not overdo it!).

3. Apply thread locker to the bolt threads 4. Adjust the bushings so that the door has a slight tilt forward (1–2 mm). (for example, Loctite 222).

4. Adjust the bushings so that the door has a slight tilt forward (1–2 mm).

Video instructions and additional materials

For clarity, we recommend that you familiarize yourself with the video instructions on rehanging refrigerator doors Ariston Hotpoint. Please note that the process may vary slightly depending on the model, but the general principles remain the same:

🎥 Video on the topic:

• 🔧 Reversing the door on Ariston HB 1801 (two-chamber, top freezer).
• ❄️ Door adjustment on Hotpoint HBM 1182 (with No Frost system).
• 📺 Replacing the seal on Ariston MBC 1182 (with display).

If you are not confident in your abilities, download official instructions for your model from the website Hotpoint-Ariston (enter the serial number of the refrigerator in the search). The manual usually contains hinge layout and list of tools.

For models with touch control (for example, Hotpoint HBM 2052) after rehanging the door may be required reflashing the controller. This is due to changes in the position of the sensors. If the refrigerator displays an error E4 or F1, contact the service center - independent intervention in the firmware can lead to equipment failure.

⚠️ Attention: Design details hinges and the location of the fasteners may differ depending on the year of manufacture of the refrigerator. For example, models Ariston 2020–2023 use hinges with quick-release fasteners, while older ones use classic bolts. Check the latest information in the documentation for your model.

FAQ: Frequently asked questions about reversing the door

Is it possible to rehang the door on an Ariston Hotpoint refrigerator yourself if you have no experience?

Yes, the procedure does not require special skills, but it is important to follow the instructions and take your time. Start with simple models (for example, HB 1801) - they have a minimum number of loops. If you have a model with a display or an ice maker, it is better to invite a technician, as there is a risk of damaging the electronics.

What to do if, after rehanging, the door does not close tightly?

There may be several reasons:

1. Hinges are skewed - loosen the bolts and adjust the position of the door according level.
2. Wear of the seal - try restoring its shape with hot water or replace it with a new one.
3. Debris gets into the groove of the seal - clean it and apply silicone grease.

If the problem persists, check whether the hinges are deformed when moving out.

Is it necessary to defrost the refrigerator before hanging the door?

Compulsory defrosting is not required, but if there is a lot of ice in the freezer, it is better to remove it - this will make access to the hinges easier. On models with No Frost defrosting is not needed, but after re-hanging the door it is recommended to run the refrigerator in mode Super Cool for 1-2 hours to stabilize the temperature.

How much does it cost to re-hang the door at the service center?

The cost of the service depends on the model and region, but in average:

• For simple models (1-2 loops) - 1500-2500 rubles.
• For refrigerators with a display or No Frost - 2500-4000 rubles.
• For Side-by-Side - from 4000 rubles.

Independent re-hanging will only cost the cost of tools (if you don’t have them) or a new seal (about 1000–1500 rubles).

Is it possible to re-hang the door on a refrigerator with an ice maker?

Yes, but it is more difficult due to the additional tubes and wires. The main risks:

• Kinking of the water supply tube - can lead to a leak.
• Damage to the ice maker sensor - flashing will be required.

If you are not sure, it is better to contact a specialist. In the service center for such models, special templates are used to mark new holes for the hinges.