Rehanging the refrigerator door Atlant is a task that many owners face when moving, renovating, or simply wanting to optimize space in the kitchen. Unlike European brands, where this procedure often requires calling a technician, Belarusian refrigerators Atlant are designed with self-service in mind. But there are nuances: models with a display, system No Frost or a freezer at the bottom have unique fastenings, and errors during dismantling can lead to depressurization of the seal or damage loops.
In this article you will find step-by-step instructions with photos, a table of tool compatibility for different series Atlant, as well as answers to Frequently asked questions - for example, what to do if, after rehanging, the door does not close well or condensation appears. We will analyze both single-chamberand two-chamber models, including popular series MHM, NRB and HM.
⚠️ Important: If your refrigerator is under warranty, re-hanging the door yourself can void it. Check this point with the service center Atlant before starting work.
1. Preparation: tools and conditions
Before you start work, check whether your refrigerator is included Atlant plugs for fastenings on the opposite side. On new models (released after 2020), they are usually taped to the back wall or packaged in a separate bag. If there are no plugs, you can order them from an official dealer or use decorative overlays from furniture fittings (the diameter of the holes must match!).
The list of necessary tools depends on the model, but the basic set is as follows:
- 🔧 Phillips screwdriver (PH2 or PH3 - for most models)
- 🔧 5 mm hexagon (for series XM-6021, XM-6026)
- 🔧 Wrench 10 mm (for the lower hinges of two-chamber refrigerators)
- 📏 Level (for checking the vertical position after installation)
- 🧴 Silicone grease (for seal and hinges)
⚠️ Attention: If your refrigerator is equipped with electronic display (for example, model ATLANT XM 6321-101 or ATLANT MXM 2835-90), before rehanging doors be sure to disconnect it from the network. Otherwise, the overvoltage protection may work and the refrigerator will be blocked.
2. Door fastening scheme: how the models differ
The design of the hinges depends on Atlant depends on refrigerator type and year of manufacture. For example, in old single-chamber models (before 2015) used separable hinges with nuts, and in the new ones - non-separable brackets, which are fastened with rivets. Below is a table with the key differences:
| Refrigerator type | Series (example) | Hinge type | Weighing features |
|---|---|---|---|
| Single-chamber | MX 2820, MX 2826 | 2 loops (top + bottom) | Replacement of the handle and plugs for bolts is required |
| Two-chamber (freezer on top) | XM 6021, XM 6026 | 3 hinges (2 per refrigerator, 1 per freezer) | The freezer door is hung separately, hexagons are needed |
| Two-chamber (freezer from below) | NRB 2312, NRB 2318 | 4 hinges (middle through) | Complicated dismantling of the middle hinge, door support required |
| Side-by-Side | ATLANT SBS 553 | 6 hinges (3 for each door) | Overhanging is not provided for by the design! |
🔹 Key point: In models with a system No Frost (for example, ATLANT XM 6326-100), when the door is hung, air duct, which is responsible for the circulation of cold air, may shift. If after installation the refrigerator begins to freeze worse, check the position of the air duct (it should fit snugly against the back wall).
What to do if there are no plugs for the holes?
If the plugs are lost, you can use furniture caps (sold at IKEA or Leroy Merlin) or cut them out of white plastic yourself. The main thing is that the diameter matches the holes (usually 8–10 mm).
3. Step-by-step instructions: rehanging the door of a single-chamber refrigerator
Let's look at the process using the example of a popular model ATLANT MHM 2831-90. This instruction is also suitable for other single-chamber refrigerators of the series MHM i MX (2018–2026 years of production).
Step 1. Dismantling the top hinge
- ✅ Unplug the refrigerator and take out all the products.
- ✅ Open the door 90° and place it under it a book or a wooden block (so as not to damage the seal).
- ✅ Unscrew 2 bolts on the top hinge using a Phillips screwdriver. Do not lose the washers - they may differ in size thickness!
- ✅ Remove the loop and move it to the opposite side, aligning it with the holes.
Step 2. Rearranging the handle and plugs
- ✅ Carefully remove the handle: it is usually attached to 2 self-tapping screws under the decorative trim.
- ✅ Move the handle to the other side, having first removed the plugs from the holes (they can be pryed off with a flat screwdriver).
- ✅ Install the plugs on the old holes - they should fit tightly, without gaps.
Step 3. Adjusting the lower hinge
- ✅ Unscrew nut on the lower hinge (you will need a 10 mm wrench).
- ✅ Remove the door by lifting it up. Be careful - it is heavier than it looks!
- ✅ Move the bottom hinge to the other side and secure it.
- ✅ Place the door on the top hinge and carefully lower it onto the bottom, aligning the pin with the hole.
☑️ Check after rehanging
4. Nuances for two-chamber refrigerators
Two-chamber models Atlant (for example, XM 6026-000 or NRB 2318-000) require a special approach due to the presence of two doors and medium hinges. Here are the key differences from single-chamber ones:
🔹 Freezer compartment: Its door is hung separately, and for this you need to remove top decorative panel (it is attached with latches or 2 screws).
🔹 Middle hinge: In models with a freezer at the bottom (series NRB), the middle loop is through and is attached to 4 bolts. Its dismantling requires support of both doors at the same time.
🔹 Electronic modules: If the refrigerator is equipped with a display (for example, ATLANT XM 6321-101), before rehanging remove decorative frame around the screen - it interferes with access to the hinges.
⚠️ Attention: In models with the system No Frost after re-hanging the door, it may be required reinstalling the air duct. If you notice that the refrigerator has taken longer to gain temperature, check to see if the air duct tube behind the back wall has moved.
5. Common mistakes and how to avoid them
Even if you carefully follow the instructions, you can make mistakes that will lead to poor fit of the seal, distortion of the door or loss of tightness. Here are the most common:
- ❌ Uneven tightening of the bolts → the door warps. Solution: Tighten the bolts crosswise, like the wheels of a car.
- ❌ Loss of washers or gaskets → play in the hinges. Solution: Use the washers from the kit or select similar ones thickness.
- ❌ Damage to the seal → condensation and ice. Solution: Before work, seal the seal with masking tape.
- ❌ Ignoring the level check → the door opens spontaneously. Solution: Adjust the height of the refrigerator legs.
🔹 How to check the tightness? After re-hanging the door, put a turned-on flashlight inside the refrigerator, close the door and see if there are gaps. If light leaks out, the seal requires adjustment or replacement.
6. Features for models with a display and No Frost
Refrigerators Atlant with electronic control (for example, ATLANT XM 6326-100 or ATLANT MXM 2835-90) have additional nuances:
🔹 Display: When reversing the door you need disconnect the power cable (it goes from the control module to the display). In models 2022–2026, the cable is attached to the connector - just remove it. In older versions, you may need to unsolder the contacts.
🔹 No Frost: The fan and air duct are located behind the rear wall. If, after rehanging, the refrigerator begins to freeze worse, check:
- 🌀 Is the air duct pinched (it should be straight).
- 🌀 Is the fan displaced (it should rotate freely).
- 🌀 Is the door thermal insulation damaged (if the seal is loose, cold air will go away).
⚠️ Attention: In models with inverter compressor (for example, ATLANT XM 6321-101) after rehanging the door it may work protection from vibration. If the refrigerator does not turn on, unplug it for 5 minutes and turn it on again.
7. If something goes wrong: diagnosing problems
After re-hanging the door, problems may occur. Let's look at the most common ones and how to fix them:
| Problem | Possible cause | Solution |
|---|---|---|
| Door does not close tightly | Hinges skewed or worn out seal | Adjust the hinges, check the seal for cracks |
| Condensation has appeared on the walls | The tightness is broken or the air duct is displaced | Check the seal fit and position air duct |
| The refrigerator has become louder | The door is touching the internal elements | Tighten the hinges or adjust the height of the legs |
| The display does not work | The power cable is damaged | Check the connection of the cable to the control module |
🔹 What to do if the seal comes off? It can be temporarily glued to double-sided tape, but it is better to replace it. Original seals for Atlant cost from 800 to 1500 rubles (depending on the model).
🔹 If the door sags: This means that they have weakened top hinges. Tighten the bolts or add additional washers for rigidity.
FAQ: Answers to frequently asked questions
Is it possible to reverse the door of the Atlant Side-by-Side refrigerator?
No, in models Side-by-Side (for example, ATLANT SBS 553) reversing the doors is not provided for by the design. The hinges in them are asymmetrical, and the electronics are rigidly tied to the position of the doors.
How much does it cost to rehang a door in a service center?
The cost of work in official service centers Atlant - from 1,500 to 3,000 rubles (depending on the model). If the seal or hinges need to be replaced, the price will increase by the cost of spare parts.
What to do if the refrigerator does not turn on after rehanging?
Most likely, the overvoltage protection has tripped. Unplug the refrigerator for 10-15 minutes, then turn it on again. If the problem persists, check the display connection (for models with electronic control).
Do you need to hang the freezer compartment separately?
Yes, in two-chamber models the freezer door is hung independently of the refrigerator door. To do this, you will need to remove the top decorative panel and unscrew the hinges of the freezer.
Is it possible to hang the door without the help of a second person?
Technically, yes, but it is difficult - the door is heavy, and it needs to be held when dismantling. For single-chamber models, you can do without an assistant by placing a support under the door. For two-chamber rooms, it is better to invite a second person.