We rehang the doors of the Atlant refrigerator to the other side: instructions with photos and nuances

Re-hanging refrigerator doors Atlant is a task faced when moving, renovating or the banal need to optimize space in the kitchen. Despite the apparent complexity, the procedure does not require calling a specialist if you approach the matter systematically. The main thing is to understand the design of the fasteners, prepare the tools and follow the algorithm, taking into account the model of your refrigerator.

In this article we will analyze the process step by step: from dismantling old hinges to installing doors on the opposite side. We will pay special attention to typical errors (for example, improper adjustment of hinges or damage to the seal), which can lead to leakage and increased energy consumption. You will also find a tool compatibility table, tips for maintaining the warranty and answers to frequently asked questions.

Important: the design of the hinges and the method of fastening the doors may vary depending on the Atlant series (for example, XM-4021 vs XM-6025) and year of manufacture. If your model is older than 2010, check the availability of spare parts in advance - some hinges and plugs may have been discontinued.

Preparation: tools and conditions

Before starting work make sure you have everything you need. The absence of even one tool can interrupt the process in the middle. Here is the basic set:

• 🔧 Phillips screwdriver (usually PH2) - for most models Atlant.
• 🔧 5 mm hexagon - for hinges of some series (for example, Atlant XM-4424).
• 📏 Ruler or square - to check the evenness of the installation.
• 🧲 Magnet (optional) - will help hold small screws.
• 🧴 Silicone grease - for processing loops after rehanging.

Also prepare the work space:

• 🚪 Clear access to the refrigerator from all sides (at least 1 m of space).
• 🔌 Disconnect the appliance from network 2-3 hours before starting work —this will allow the ice on the seal to defrost and make dismantling easier.
• 🧊 Remove all products and shelves from the door (eggs, bottles, etc.) so as not to damage them.

Step 1: Removing the doors - procedure

Start from the top hinge of the refrigerator compartment (if the model is two-chamber). The algorithm is as follows:

1. Open the door 90° and fix it (for example, place a book under the bottom).
2. Remove decorative plug from the hinge (pry it off with a flat screwdriver or knife).
3. Unscrew the screws holding the hinge on the refrigerator body.
4. Carefully remove the door from the top hinge and place it on a soft surface (such as a blanket).

For the freezer, the process is similar, but there is a nuance: the lower hinge is often attached to the baskets. You will have to first remove the baskets and then unscrew the hinge. Atlant with the No Frost system (for example, XM-4626) the lower hinge can be hidden under a plastic panel - it must first be removed.

Step 2: Transferring the hinges to the other side

After dismantling the doors, you need to move the hinges to the opposite side. It is important here not to confuse left and right. hinges they are mirrored! There are usually marks on the refrigerator body and door (letters L and R or arrows) indicating the correct position.

Transfer instructions:

1. Remove the hinges from the doors by unscrewing the screws from the inside.
2. Move them to the opposite side, aligning them with the existing holes. If there are no holes, use template (usually goes in). complete with the refrigerator).
3. Fasten the hinges on the door without fully tightening the screws (adjustment will be required later).
4. Install the hinges on the refrigerator body in new positions.

B models Atlant with electronic display (for example, XM-6321) may require transfer wiring door opening sensor. For this:

• 🔌 Disconnect the sensor connector from the control board (usually located under the top shelf of the refrigerator compartment).
• 📍 Lay the wire along a new route, avoiding kinks.
• 🔌 Connect the connector back, making sure it is secure contact.

What to do if there are no holes for the hinges on the other side?

In this case, use the template that came with the refrigerator. Attach it to the body and door, then carefully drill the holes with a drill (drill diameter - 4-5 mm, use low metal drills). speed to avoid chipping.

Step 3: Door installation and adjustment

Now you can return the doors to their place. Start with the top hinge of the refrigerator compartment:

1. Place the door onto the hinge pin and lightly press.
2. Insert the screws and tighten them not all the way (leaving ~1 mm play for adjustment).
3. Repeat the process for the bottom hinge.
4. Install the freezer door (if any).

After preliminary assembly, check:

• 🚪 Closing the doors —they should fit evenly, without gaps.
• 🔄 Opening 90° —the door should not close spontaneously or open further.
• 📏 Vertical alignment —use a level or visually assess the gaps at the top and bottom.

If the door skewed or does not fit tightly, adjust the hinges:

• 🔧 Loosen the screws on the problem hinge.
• 🔄 Raise or lower the door to the correct one position.
• 🔧 Tighten the screws and check the result.

Typical mistakes and how to avoid them

Even if you carefully follow the instructions, you can make mistakes that will lead to leakage, creaking hinges or breakage of fastenersLet's consider the most common:

Critical error: ignoring marks L/R on the hinges. In 80% of cases, this leads to the inability to close the door without physical force, which over time deforms the seal and increases the load on the compressor.

Another common problem is for hinges on the old and new sides. If your model mismatch of holes for hinges on the old and new sides. If in your model Atlant has no holes, do not try to drill them by eye. Use a template or refer to the instructions for a specific model (for example, for XM-4026 the template is included).

Features for different models Atlant

The design of the hinges and the method of fastening the doors may vary depending on the series. Below are the key differences:

• 🔹 Atlant XM-4021, XM-4026: The hinges are fastened with 3 screws, there are already holes for transfer on both sides.
• 🔹 Atlant XM-6025, XM-6321: The upper hinge of the refrigerator compartment has decorative cover, which must be removed before dismantling.
• 🔹 Atlant with No Frost (XM-4626, XM-5124): The bottom hinge of the freezer is hidden under a plastic panel. To gain access, you need to remove the panel by unscrewing 2 screws.
• 🔹 Atlant two-chamber (MXM-170, MXM-280): The freezer compartment has additional bracketwhich also needs to be moved.

For models with electronic control (for example, XM-6321-100) after rehanging, you may need reset settings. To do this:

1. Disconnect the refrigerator from the network for 5 minutes.
2. Turn on and hold button Super Cool (or Super Freeze) 10 seconds.
3. Wait for the sound signal - this is confirmation of the reset.

How to understand that the door is hung correctly?

After installation, check:

- The door closes with a slight push (without force).

- The seal fits evenly around the entire perimeter (run a sheet of paper - it should hold tightly).

- There is no creaking or play when opening/closing.

- Display (if any) works correctly, there are no errors like E1 or E2 (fault codes for Atlant).

Keeping the warranty and contacting service

If your refrigerator Atlant under warranty, independent re-hanging of doors may cancel it. According to the conditions of most service centers, any intervention in the design (including moving hinges) is considered a violation. However, there are exceptions:

• 📄 instructions for the model explicitly allowed reversing the doors by the user (for example, in Atlant XM-4021 this is written on page 12).
• 🔧 You use original spare parts (screws, hinges, plugs) from the kit.
• 📋 Work completed without damage case or seal.

If you are in doubt, contact official service center Atlanta and check whether your model is covered by the warranty after rehanging. In some cases, specialists are ready to do the work free (for example, if the refrigerator was purchased less than 3 months ago).

⚠️ Attention: Terms of warranty service may change. Check the latest information in the product passport or with the seller.

FAQ: Frequently asked questions about rehanging doors Atlant

Is it possible to hang the door on a refrigerator Atlant with one compressor?

Yes, but keep in mind that in single-compressor models (for example, Atlant MX-2824) the freezer often has a separate hinge, which also needs to be moved. If you do not do this, the freezer door will open in the opposite direction, which is inconvenient.

How long does re-hanging take?

B on average - 1–1.5 hours if you have tools and an assistant. If you have to drill new holes or adjust the hinges several times, the process can take up to 2–3 hours.

What to do if, after rehanging, the refrigerator begins to work loudly?

This may be due to:

• 🔊 Disk of the door —check the fit seal.
• 🔊 Loosening of the compressor fastenings (if its fastenings were touched when moving the hinges).
• 🔊 Vibration from incorrectly installed baskets in the freezer.

Disconnect the refrigerator, check all fastenings and re-adjust the hinges.

Is it necessary to defrost the refrigerator before rehanging?

It is advisable, but not necessary. If there is ice on the seal, it can interfere with neat operation. dismantling. It is enough to turn off the refrigerator 2-3 hours before work so that the ice melts.

Where can I get a template for drilling holes if it is not included?

You can download the template:

• 📄 Download from the official website Atlant (section "Documentation" for your model).
• 📏 Make it yourself by measuring the distance between the holes on the old side and transferring the markings to the new one.
• 🔧 Order from a service center (sometimes they provide it for free).