We move the Atlant refrigerator door to the other side: instructions with photos and videos

Reversing the refrigerator door Atlant to the opposite side is a task that many owners face when moving, renovating a kitchen, or the banal need to optimize space. Unlike European brands, where this procedure often requires calling a specialist, Belarusian refrigerators are structurally adapted for moving the door yourself. However, even here there are nuances: models with a display, system No Frost or non-standard hinges may require additional actions.

In this article you will find step-by-step instructions with photosan analysis of the features for popular series (MHM, HM, HP), as well as unique tips for avoiding common mistakes - for example, why after rehanging the door may not close well or condensation may appear. If your refrigerator was manufactured after 2018, check for the presence of plastic plugs on the opposite side - their absence may mean that the model does not support double-sided fastening!

Preparation: tools and safety

Before you begin, make sure that you have everything you need. Most models Atlant are equipped with a set for hanging (wrench, screwdriver, plugs), but if you don’t have it, prepare the tools yourself.

• 🔧 Phillips screwdriver (size PH2) - for hinge and handle screws.
• 🔨 10 mm wrench — for attaching the lower hinge (in some models - 8 mm).
• 📏 Ruler or square —to check the evenness of the door installation.
• 🧴 Silicone grease (optional) - for processing hinges after overweight.
• 🧲 Magnet - will help hold small screws and not lose them.

Important: unplug the refrigerator 1-2 hours before starting work. This will allow the sealing rubber to defrost, which will become more elastic and less susceptible to deformation. If there is ice in the freezer, remove it to avoid leaks when tilting the case.

⚠️ Attention: In models with electronic display (for example, Atlant XM 6025-031) after rehanging it may be necessary reset settings through the menu. Otherwise, the temperature indicators will be displayed mirrored!

Step 1: Dismantling the old door

Start with the top hinge - it is usually fixed with 2-3 screws under Phillips screwdriver. In models Atlant MHM 1840-80 and similar screws can be hidden by a decorative cover - carefully pry it off with a flat screwdriver.

Action algorithm:

1. Open the door to 90° and support it a chair or assistant - it is heavier than it looks!
2. Unscrew the screws of the upper hinge, remove the hinge and carefully lift the door up to free it from the lower pin.
3. Remove the door to the side, placing it on a soft surface (for example, a blanket) so as not to scratch it.

The bottom hinge in most models is secured with a nut, which must be unscrewed with a wrench. Be careful: in refrigerators with No Frost there may be drain tube under the hinge - do not pull it or bend it!

Step 2: Transferring the hinges to the other side

On the opposite side of the case you will see symmetrical holes for the hinges, closed with plastic or rubber plugs. In models Atlant NR 1050-022 and newer, the plugs may be on latches - pry them off with a screwdriver.

Important nuances:

• 🔄 Screws loops not symmetrical —the upper and lower ones have different lengths. Do not confuse them when installing!
• 📌 In refrigerators with touch panel (for example, Atlant XM 6321-100) a transfer may be required display power cable —it is usually attached to the top loop.
• 🔧 If there are no holes for hinges, your model does not support overhanging (relevant for some budget series).

Install the hinges in a mirror order: the top one in place of the bottom one, and vice versa. Tighten the screws not all the wayso that you can then adjust the position of the door.

Step 3: Installing the door on the new side

This is the most critical stage. Take the door, align the bottom pin with the hole in the hinge and carefully lower it down. Fasten the top hinge by 1-2 turns of the screw, then check:

• 📏 Gaps along the perimeter of the door - they should be the same (2-3 mm).
• 🔄 Stroke doors - it should open smoothly, without creaks.
• 🧲 Sealant fit —if there are gaps, adjustment will be required.

In models with double-chamber doors (freezer + refrigerator), the upper door is installed first, then the lower one. At the same time freezer compartment the refrigerator should open - this prevents icing of the seal. after refrigeration - this prevents the seal from icing.

⚠️ Attention: If after installation the door opens on its own at an angle of 45°, this means that the refrigerator is not level. Adjust the height of the legs or use a building level!

What to do if the door creaks after hanging?

The creaking usually occurs due to insufficient lubrication of the hinges or their misalignment. Remove the door, apply silicone grease to the hinge pins and check that the door does not touch the frame when opening. If the squeak remains, loosen the hinge screws and adjust the door position.

Step 4: Adjustment and tightness check

After installing the door, you need to adjust its position. To do this:

1. Close the door and check seal fit along the entire perimeter. Use sheet of paper: if it pulls out easily, the seal does not fit tightly.
2. If there are gaps, loosen the hinge screws and slightly move the door in the desired direction. Models Atlant XM 6321-100 are provided for this adjusting washers.
3. Check opening angle —the door should be fixed in the 90° position and do not close spontaneously.

To test the tightness, use flashlight: place it inside the refrigerator, close the door and turn off the light in the room. If a gap is visible, the seal requires replacement or adjustment.

In models with No Frost after rehanging, condensation on the wallsmay temporarily appear. This is normal - the ventilation system adapts to the new position of the door within 1-2 days.

Features for models with a display and No Frost

Refrigerators Atlant with electronic control (series XM 6000, XM 6300) require additional actions:

• 📺 Relocating the display cable: it is usually attached to the top hinge. Carefully disconnect the connector and secure the cable to the new loop using zip ties.
• ⚙️ Reset settings: after rehanging, hold the buttons Super Cool + Super Freeze for 5 seconds to reset the sensor calibration.
• ❄️ Checking the No Frost system: turn on the refrigerator and make sure that the fan in the freezer is working (you can hear it when the door is open).

In models with freshness zone (for example, Atlant XM 4426-080) after reweighing may be required reconfiguring temperature zones. To do this:

1. Go to menu Settings → Temperature Zones.
2. Select mode Auto for automatic calibration.
3. Wait 12-24 hours for the system to adapt.

⚠️ Attention: Display connection details may vary depending on the year of manufacture. Models 2020–2023 use connector JST PH 2.0, older ones use connector Molex 51021-0300. Do not confuse them when connecting!

Common mistakes and how to avoid them

Even if you carefully follow the instructions, you can make mistakes that will lead to not closing the door tightly, loss of cold or broken hinges. Here are the most common of them:

• 🔀 The upper and lower hinges are mixed up → the door hangs crooked. Solution: change them in places.
• 🔩 The screws are not tightened → over time the hinges become loose. Solution: use a torque wrench with a force of 1.5–2 Nm.
• 🧊 The seal is damaged → ice and increased energy consumption. Solution: heat the rubber with a hairdryer or replace it.
• ⚡ Settings have not been reset (for models with a display) → incorrect temperature display. Solution: reset according to the instructions above.

If, after rehanging, the refrigerator becomes makes more noise, check:

• Does it touch the door internal shelves when opening.
• Have compressor fastenings (relevant for models Atlant MXM 1635).
• Have you hit garbage in the fan (for No Frost).

In 80% of cases, increased noise is eliminated adjusting the legs of the refrigerator. Use a level to level the case vertically and horizontally.

FAQ: Answers to popular questions

Is it possible to re-hang the door on the Atlant refrigerator yourself if it is under warranty?

Yes, re-hanging the door is not a warranty caseif you have not damaged the case or internal parts, however, if problems arise after the procedure (for example, the display does not work), the warranty is valid. on this particular malfunction may be cancelled. We advise you to take a photograph of the process to confirm the absence of mechanical damage.

How long does it take to rehang the door?

On average - 40–90 minutes, depending on the model and experience. The most time is spent on adjusting the door and checking the tightness. If the refrigerator has No Frost and a display, add another 20-30 minutes for moving cables and resetting settings.

What to do if, after rehanging, the door does not close tightly?

The reasons may be different:

1. Hinge distortion — loosen the screws and adjust the position of the door.
2. Deformation of the seal —warm up use a hairdryer or replace it.
3. Uneven floor —adjust the legs of the refrigerator.
4. Ingress of debris —check if something is preventing the closure (for example, a label or a piece of cling film).

If the problem persists, check magnetic tape in the seal. In older models it may become demagnetized.

Is it necessary to defrost the refrigerator before overweight?

Desirable, but not necessary. Defrosting is needed for:

• Removing ice in the freezer (so as not to damage the drainage system when tilting).
• Softening the sealing rubber (it will become more elastic and less deformed).

If there is no refrigerator No Frost and no ice, you can do without defrosting. However, unplug it during the work it is still necessary!

Is it possible to rehang the door on Atlant models older than 10? years?

In most cases - yes, but there are nuances:

• Models until 2010 may not have holes for hinges on the opposite side.
• Sealant for 10 years could lose elasticity - after re-hanging it will have to be replaced.
• Old refrigerators are used metal hingeswhich rust over time. Before installation, clean them of corrosion and lubricate them.

If your model was released before 2005, check the availability spare plugs -they may not have been included.