Adjusting the legs of the Atlant refrigerator: instructions with photos and advice from the experts

The refrigerator Atlant is a reliable technique, but even it requires proper installation for smooth operation. One of the key procedures is the adjustment of the legs, which affects not only the stability of the unit, but also the efficiency of its operation. Incorrectly adjusted supports can cause increased noise, uneven compressor wear and even condensate leakage. In this article we will look at how to level the refrigerator yourself, what tools you will need and what to pay attention to when setting it up.

The process of adjusting the legs of models Atlant (whether MHM-1708, MX-2824 or other series) has general principles, but may differ in details. For example, older models often have fixed supports, while new ones have screw supports with the possibility of fine adjustment. We will look at universal methods suitable for most refrigerators of this brand, and also point out nuances that will help avoid typical mistakes.

Why adjust the legs of the refrigerator Atlanta?

Many users underestimate the importance of the correct position of the refrigerator, believing that it is enough to simply place it on a flat floor. However, even a minimal misalignment can lead to serious consequences:

• 🔊 Increased noise during compressor operation due to vibration transmitted to the housing.
• 💧 Condensation accumulation at the bottom of the chamber if the refrigerator is tilted forward.
• 🔄 Incorrect closing of the door, which leads to loss of cold and increased energy consumption.
• ⚡ Increased load on the engine, reducing the service life of equipment.

According to service centers, up to 30% of warranty claims are related to the consequences of incorrect installation, including adjustable legs. In this case, the procedure takes no more than 15 minutes and does not require special skills.

Preparing for adjustment: tools and conditions

Before you start adjusting, make sure you have everything you need. For most models Atlant you will need:

• 🔧 Wrench (usually 10 or 13 mm, depending on the model).
• 📏 Level (bubble or laser) with a length of at least 50 see
• 🧲 Screwdriver (cross or flat - for dismantling decorative panels if the legs are hidden).
• 🧹 Rag or napkins to clean the supports from dust.

Also check the following conditions:

⚠️ Attention: If the refrigerator has been recently moved, wait 4–6 hours before making adjustments. This time is necessary to stabilize the pressure in the cooling system.

If the floor in the room is uneven, use anti-slip pads or special adjustable supports, which are sold in hardware stores. For models Atlant with a system No Frost it is especially important to maintain a horizontal position, since disruption of air circulation can lead to freezing of the evaporator.

Step-by-step instructions: how to adjust the legs

The algorithm of actions is the same for most refrigerators Atlant, but may differ slightly depending on the design of the legs. Let's consider the universal method:

1. Step 1. Access to the legs.
   

   For most models, the supports are located in the front (sometimes hidden under a decorative panel). They usually stand behind rollers or fixed supports. If the legs are covered with a plastic cover, carefully remove it with a screwdriver.

2. Step 2. Initial assessment.
   

   Rock the refrigerator back and forth and left and right. If it wobbles, this is a signal that adjustment is needed. Also check if the back wall is touching the furniture or the wall - this may interfere with the correct position.

3. Step 3. Using a level.
   

   Place the level on the top lid of the refrigerator (parallel to the front wall). If the bubble is displaced, you need to tighten the legs. For accuracy, check the level along the diagonals.

4. Step 4. Adjustment.
   

   • 🔩 For lifting legs, rotate the screw clockwise arrow.
   • 🔩 For lowering — counterclockwise.
   • 🔄 Adjust alternately: first one side, then the other to avoid distortion.

Step 5. Checking the door.

After alignment, open the door 45° - it should remain in this position or close slowly. If the door opens spontaneously or closes too quickly, adjust the tilt forward/backward.

Is the refrigerator unplugged?|Has debris been removed from under the legs?|Is there access to the adjusting screws?|Is the level prepared?-->

For models with electronic display (for example, Atlant XM 6025-089) after adjustment may be required error resetif a malfunction code related to misalignment was previously displayed. Usually, to do this, it is enough to turn off the refrigerator for 1-2 minutes and turn it on again.

Adjustment features for different Atlant models

Refrigerators Atlant are produced in several series, and the design of the legs may differ. Here are the key nuances:

For refrigerators with water dispenser (for example, Atlant MY 2401-089) the adjustment must take into account the additional weight of the tank. In such cases, it is recommended to slightly raise the front part (by 1–2 mm) to compensate for the load.

What to do if the leg does not turn?

If the adjusting screw jammed, do not use excessive force - this may break the plastic housing of the leg. Try cleaning the threads from rust with WD-40 or another product, then carefully turn them with a wrench. If the leg is damaged, it can be replaced with a universal one (suitable models: Atlant 5301-00001020 for front supports).

Typical mistakes and how to avoid them

Even with the apparent simplicity of the procedure, many make mistakes that subsequently lead to breakdowns. Here are the most common:

• ❌ Adjustment "by eye" without using a level. This leads to a hidden distortion, which manifests itself over time.
• ❌ Over-tightening of the legs. May deform the door seal or damage the thread.
• ❌ Ignoring the rear supports. If the rear legs (or rollers) do not touch the floor, the refrigerator will “walk” when the door is opened.
• ❌ Adjustment on a soft surface (carpet, linoleum without a base). Over time, the supports will “sag” and you will have to repeat the procedure.

⚠️ Attention: If after adjustment the refrigerator begins to vibrate more strongly, check whether its body is touching furniture or walls. Vibration can be transmitted through contacting surfaces, even if the refrigerator itself is level.

Another common problem is uneven weight distribution. For example, if the refrigerator is loaded with food on only one side, this may cause misalignment. In such cases, it is recommended:

1. Distribute the products evenly on the shelves.
2. Check the level 1-2 days after loading (especially important for models with freshness zones).

How to check the result of the adjustment?

After adjusting the legs, you need to make sure that the refrigerator is positioned correctly. Here are several ways to check:

1. Door test.
   

   Open the door 90° and release it. It should remain in this position or close very slowly. If the door closes itself (or, conversely, opens. further), adjust the tilt forward/backward.

2. Checking vibration.
   

   Turn on the refrigerator and listen. Normally, you should hear a uniform hum of the compressor without rattling. If vibration remains, check whether the tubes are touching the back wall of the furniture.

3. Control. condensation.
   

   A day after adjustment, inspect the bottom of the refrigerator. If water accumulates under it, it may be tilted forward and condensation does not flow into the drainage hole.

4. Use a level.
   

   Re-check the horizontal position on the top cover. Allowable misalignment is no more than 1-2. mm.

For models. c electronic control (for example, Atlant MY 1801-089) after adjustment, it may be necessary to calibrate the sensors. Usually this is performed automatically, but if an error appears on the display (for example, E1 or E2), refer to the reset instructions.

What to do if the adjustment did not help?

If after all the manipulations the refrigerator continues to stagger, vibrate or close incorrectly, the reasons may be more serious:

• 🔧 Wear of the supports. Over time, the plastic legs become loose or break. Solution: replace with new ones (original or universal).
• 🏗️ Defect floor. If the screed in the room is uneven, you may need to level the base or install additional pads.
• 🚪 Problems with door hinges. Worn or bent hinges will not hold the door in the correct position even with perfectly adjusted legs.
• ⚙️ Compressor malfunction. If vibration is accompanied by uncharacteristic sounds (knocking, grinding), this may indicate a breakdown engine.

⚠️ Attention: If the refrigerator Atlant is under warranty, do not try to disassemble the supports or hinges yourself. This may lead to loss of warranty obligations. Contact the service center with a description of the problem.

To diagnose problems with hinges, you can perform a simple test:

1. Open the door and lift it by the top edge.
2. If you feel play of more than 3-5 mm, the hinges require tightening or replacement.

In cases where the cause of vibration is faulty compressor, adjusting the legs will not help. Signs of such a breakdown are:

• A constant hum without pauses (the compressor does not turn off).
• Heating of the housing in the lower part.
• Lack of cooling when the engine is running.

FAQ: Frequently asked questions about adjusting the legs of the Atlant refrigerator

Is it possible to adjust the legs of the Atlant refrigerator without a level?

Theoretically, yes, but this is fraught with errors. Without a level, it is difficult to notice a 1-2 mm misalignment, which will eventually lead to problems with the door or vibration. In extreme cases, you can use improvised means: place a glass with it on the refrigerator. water (along the edge) and adjust the legs so that the surface of the water is parallel to the floor.

How often should you check the adjustment of the legs?

It is recommended to check the position of the refrigerator every 6-12 months, as well as after:

• Rearranging equipment.
• Repairing the floor or furniture nearby.
• Heavy loading/unloading of products.

If the refrigerator is on a wooden floor or linoleum, the check should be carried out more often - once every 3-4 months, since the coating may sag.

What to do if there is only one leg broken?

A broken leg can be replaced with an original one (the part number is indicated in the refrigerator's passport) or a universal one. For models Atlant threaded supports are suitable M8 or M10 (depending on the model):

1. Disconnect the refrigerator from the network.
2. Lift the corner of the refrigerator (you can use a jack or the help of a second person).
3. Unscrew the fastening of the broken leg and install a new one.
4. Adjust the height to level.

If there is no replacement at hand, you can temporarily use a durable wooden lining, but this is not a long-term solution.

Why does the Atlant refrigerator vibrate even after adjustment?

The reasons for vibration may not be related to the legs:

• Touching of the rear wall tubes about furniture or wall (check the gap of at least 5 cm).
• Wear of compressor shock absorbers (replacement required).
• Incorrect installation of the transport bolts (if the refrigerator was recently delivered, check whether the bolts securing it have been removed compressor).
• Uneven floor (even when adjusting the legs, if the differences in the floor are significant, vibration will be transmitted to the housing).

If the vibration is accompanied by uncharacteristic sounds (knocking, grinding), contact the service.

Is it possible to use pads instead of adjusting the legs?

Pads (for example, made of rubber or wood) can be used as temporary. solution, but they will not replace full adjustment. Disadvantages of this approach:

• The pads can move, causing misalignment.
• They do not compensate for uneven floors as accurately as adjustable feet.
• In some cases, pads increase vibration (for example, if they are too soft).

If you do use linings, choose anti-slip (for example, from porous rubber) and regularly check the position of the refrigerator.