A modern two-chamber refrigerator Beko is a complex unit that requires precise calibration to maintain food freshness. After purchasing, many owners are faced with the question of how to set the temperature correctly so that the meat does not spoil and the vegetables do not freeze. Incorrect setting of the thermostat can lead not only to rapid deterioration of the contents, but also to increased energy consumption.
In this article we will analyze in detail the setting algorithms for various models, from classic mechanical rotary knobs to modern digital displays with function NeoFrost. You will learn which values are optimal for different sections and how to avoid common mistakes during initial startup.
Understanding the operating principles of your device will extend the life of the compressor. Let's look at the main stages of setting up the climate control inside the storage chamber.
Principles of operation of the Beko cooling system
Refrigerators of the Turkish brand are often equipped with a system No Frost or combined cooling. In such models, cold air circulates forcibly, which requires a special approach to setting. If you set the temperature on the regulator too low, the food in the upper tiers may dry out, and in the lower tiers it may become covered with ice.
It is important to consider that temperature sensors are located in certain areas of the evaporator. Electronic control system reads the readings and regulates the operation of the compressor. With mechanical control, you actually change the thermostat response threshold, and not the exact temperature in degrees.
⚠️ Attention: In models with Low Frost ice on the back wall is normal during certain operating cycles, but with proper settings it should disappear. Do not try to scrape off ice with a knife while the device is operating.
Different zones inside the chamber have different temperatures. The shelf above the vegetable bin is usually the coldest, while the door is warmest. This is a physical feature that must be taken into account when placing products, even if the sensor shows ideal values.
Setting a mechanical thermostat
In classic models Beko control is carried out by a rotary knob located inside the main chamber or on the top panel. The scale can contain numbers from 1 to 5, from 1 to 7 or designations Min-Max. The golden rule applies here: the higher the number, the lower the temperature (colder).
For everyday use, manufacturers recommend setting the regulator to the middle position. Usually this is a number 3 or 4 on a seven-step scale. If you set the knob to maximum, the compressor will work almost non-stop, trying to achieve an unattainable ideal in the heat, which will lead to overheating.
During initial setup, after defrosting or loading a large volume of warm food, you can temporarily increase the cooling power. However, after 5-6 hours, be sure to return the regulator to normal mode. Sharp changes in settings are harmful to the refrigerant.
Control via electronic display
More advanced series Beko are equipped with LED displays on the outside or inside of the door. Here the adjustment is made with an accuracy of a degree. To activate the editing mode, you often need to hold the Freezer or Fridge button for 3 seconds until the indicators flash.
Using the arrow buttons or symbols + and -, set the required values. After selecting the desired number, you must confirm the action by pressing the same mode button or the OK/Confirmbutton. If you do not confirm the choice within 10 seconds, the system will return to the previous settings.
The secret of resetting the settings
If the display does not behave correctly, try unplugging the refrigerator for 15 minutes. This will reset the control board and clear temporary logic errors.
Some models have a child lock feature on the control panel, indicated by a padlock symbol. If the buttons do not respond to presses, check whether this mode is activated. To unlock, you usually need to hold down the button with the image of a key or simultaneously press two adjacent keys.
Optimal temperature conditions for different products
For long-term storage of products, it is important to observe specific temperature ranges. In two-chamber refrigerators Beko the upper chamber is intended for storage at a temperature from +2 to +6 degrees, and the lower (freezing) - from -18 and below.
- 🥩 Raw meat and fish: they require the coldest mode in the main chamber, it is advisable to place them on the glass above vegetables, where the temperature is about +2°C.
- 🥛 Dairy products: feel optimal at +4°C, so the shelf in the middle is their ideal place.
- 🥦 Vegetables and fruits: do not like extreme cold and drafts, for them there is a zone in the lower containers, where it is kept about +6-8°C.
If you store a lot of perishable foods, it makes sense to lower the overall temperature in the chamber by 1 degree. However, remember that greens at temperatures below +2°C can quickly wilt and lose turgor.
Special modes: Super Freeze and Vacation
The function Super Freeze (Super Freeze) is designed for quickly freezing fresh food or creating a supply of ice. When this mode is activated, the compressor runs continuously, ignoring sensor readings. It is strictly not recommended to use it for more than 24 hours.
Mode Vacation (Vacation) switches the refrigerator compartment to an economical operating mode, preventing the appearance of mold and odor while you are not at home. The freezer continues to operate normally. This is an ideal option if you are leaving, but leave some supplies in the freezer.
| Operating mode | Refrigerator compartment temperature | Freezer temperature | Recommended use time |
|---|---|---|---|
| Standard (Eco) | +4°C ... +5°C | -18°C | Constant |
| Super freezing | Does not change | up to -24°C | Maximum 24 hour |
| Vacation | +10°C ... +12°C | -18°C | Long absence |
| Intensive cooling | +2°C ... +3°C | -18°C | After loading products |
Activation of special modes on the display is usually accompanied by the corresponding lighting indicator. To disable the function, just press the mode button again or wait for the timer to automatically turn off.
Diagnostics of temperature problems
If you have set the correct settings, but the refrigerator does not hold the temperature, the cause may not be a malfunction, but external factors. Check the tightness of the door and the condition of the seal. Even a microscopic gap leads to a constant flow of warm air.
⚠️ Attention: If a thick layer of ice forms on the back wall of the main chamber when the No Frost system is turned on, the drainage hole may be clogged. Clean it with a special soft wire or a cotton swab.
Frequently opening the door or placing the refrigerator next to the radiator also affects the cooling efficiency. In such cases, the system may not be able to cope with the load, even if the thermostat is turned up to the maximum.
☑️ Checking the serviceability of the system
If error codes appear on the display (for example, flashing numbers), refer to the instructions. Often this is a signal of a malfunction of the temperature sensor, which requires replacement by a specialist.
Frequently asked questions (FAQ)
What number should be set on the mechanical regulator in the summer?
In the summer, when the ambient temperature is high, it is recommended to set the regulator to the value 2 or 3 (out of 5). This will prevent excessive load on the compressor. If set to maximum, the refrigerator may work without rest, trying to cool the chamber in a hot room.
Why does food freeze at the back wall in the Beko refrigerator?
This can happen if the temperature is set too low (number 5-7) or if the food touches the back wall, where cold air comes out. Move the food away from the wall and reduce the cooling power.
What does a flashing temperature indicator mean?
A flashing indicator usually signals that the temperature inside the chamber has risen above a critical level. This often happens after loading groceries for the first time or after opening the door for a long time. If the flashing does not stop after a few hours, check the settings.
Can you change the temperature settings while the refrigerator is running?
Yes, electronic systems Beko allow you to change settings on the fly. However, a sharp change in the target temperature (for example, from +5 immediately to 0) will force the unit to work in enhanced mode. It is better to change the settings smoothly.
How long does it take for the refrigerator to return to normal mode after changing the settings?
Temperature stabilization after changing the settings takes from 2 to 6 hours, depending on the chamber load and the ambient temperature. Do not check the result immediately, give the system time to complete the cycle.