We rehang the Beko refrigerator door yourself: from A to Z

Rearranging the door refrigerator Beko is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Despite the apparent complexity, the procedure is quite doable at home if you know the key nuances of the Turkish brand’s design. The main thing is to take your time and follow the algorithm, taking into account the features of a particular model (for example, Beko CN 325120 or GNE 114120 have different fastenings).

In this article we will analyze the process step by step: from preparing the tools to the final adjustment of the hinges. We will pay special attention typical errorsto those that lead to door misalignment or damage to the seal, and we will also give recommendations for caring for the mechanism after rehanging. If your refrigerator is under warranty, check the conditions of the service center: some models (for example, with a system No Frost) require professional intervention to maintain warranty obligations.

For clarity, we provide a comparative table of tools and time required for different types of refrigerators Beko, as well as Let's add interactive elements: a survey about your experience, a preparation checklist, and a spoiler with the consequences of an incorrect rearrangement. Let's start with the theory - why might you even need to change the opening side?

When do you need to rehang the Beko refrigerator door?

The most common reasons for changing the door opening side are:

• 🔄 Kitchen redevelopment: furniture or appliances block easy access to the refrigerator. For example, if a new stove or cabinet was installed nearby.
• 🚪 Inconvenient for left-handers: standard right-side opening may interfere with the user's habits.
• 🏠 Moving to a new home: the doorway or furniture arrangement dictates otherwise location.
• 🔧 Damage to the hinges: if one hinge is broken, sometimes it is easier to move the door to the other side than to repair it.

It is important to consider that not all models Beko support door relocation. For example, refrigerators with built-in water dispenser (series Beko WMI) or models with French Door (two-door) may have rigidly fixed hinges. Before starting work, check:

• 📄 User instructions: in the "Installation" section it is usually indicated whether relocation is possible.
• 🔍 Hinge design: if there are no technological holes for fastenings on the opposite side, the door is not outweigh.
• 🔌 Warranty conditions: for some models, independent intervention will void the warranty.

If your model supports rearrangement, but you doubt yours forces, pay attention to models with the EasySwap system from Beko (for example, Beko RSSE315M20S). They are equipped with special hinges that allow you to change the opening side in 10–15 minutes without additional tools. However, such refrigerators are rare and usually belong to the premium segment.

Preparing for relocation: tools and safety measures

Before you start work, prepare everything you need. Missing even one tool can delay the process or lead to damage. Here is the complete list:

Also prepare:

• 🧴 Silicone grease (for example, WD-40 Specialist) for processing hinges after rearrangement.
• 🧽 Soft cloth - place it under the door so as not to scratch the floor.
• 📦 A box or stand for temporary storage doors.

Take a photo of the location of the hinges and wires (if there is a display)

Disconnect the refrigerator from the mains and defrost (if necessary)

Empty the door shelves from food

Prepare a work space (1.5–2 m² of free space)

Check the availability of spare plugs included in the refrigerator package -->

⚠️ Attention: If your refrigerator Beko is equipped electronic display on the door (models series Beko RCSK), before rearranging, be sure to disconnect the power cable! To do this:

1. Remove the top cover of the refrigerator (usually secured with 2-4 screws).
2. Carefully disconnect the cable connector by pulling the plastic fastener (not for the wires!).
3. Fix the cable with tape to the body so that it does not interfere.

If you are not confident in your skills in working with electronics, it is better to invite a specialist. Damage to the cable can lead to failure of the display or control system.

Step-by-step instructions: how to rehang the Beko refrigerator door

The process of rearranging the door can be divided into 5 key stages. We will consider a universal algorithm suitable for most models Beko (for example, CN 325120, GNE 114120, RCSK 250M20). For refrigerators with French Door or Side-by-Side additional steps may be required.

Step 1: Removing the top hinge

Start with the top fastening:

1. Close the door and secure it with masking tape in the upper part.
2. Remove the decorative plug of the hinge (pry it off with a flat screwdriver).
3. Unscrew the bolts securing the hinge to the refrigerator body (usually 2-3 pieces).
4. Holding the door, carefully remove the top loop.

Step 2: Removing the door

Now you need to separate the door from the bottom hinge:

1. Ask a helper to support the door (it is heavier than it looks!).
2. Unscrew the bottom hinge bolts (usually 1-2 pieces).
3. Carefully lift the door up to remove it from the bottom hinge pin.
4. Lay the door on a prepared surface (for example, on a table covered with a blanket).

⚠️ Attention: In models c water dispenser (for example, Beko WMI 25022) hoses pass inside the door. Do not pull the door sharply - first disconnect the hoses from the refrigerator body, clamping them with clamps to avoid leaks.

Step 3: Transferring the hinges to the other side

This step requires special care:

1. Remove the plugs on the opposite side of the refrigerator (where the new hinges will be).
2. Move the hinges to the other side using the existing holes. If there are no holes, you will have to drill them (see section "What to do if there are no holes for hinges").
3. Install the hinges in a mirror image relative to the original position.

In most models Beko the holes for the hinges are symmetrical, but in some cases (for example, y Beko GNE 124120) may be required rearranging the seal. To do this:

1. Carefully remove the rubber seal from the door, starting from the corners.
2. Rotate it 180° and install it back, starting from the top corner.
3. Warm it up rubber band with a hairdryer (temperature 50–60°C) so that it fits better into the grooves.

Step 4: Installing the door in a new place

Assembly occurs in the reverse order:

1. Place the door onto the bottom hinge pin.
2. Align it vertically (you can use a level).
3. Install the top hinge and tighten the bolts not all the way.
4. Check whether the door opens/closes freely.

Stage 5: Adjustment and final check

After installing the door:

1. Adjust the hinges using a hex key so that the door fits snugly to the body.
2. Check the seal: there should be uniform pressure around the entire perimeter (test with a sheet of paper - it should not fall out when closed doors).
3. Connect the refrigerator to the network and make sure that the display (if any) works correctly.

What to do if there are no holes for hinges on the other side?

In some models Beko (especially budget ones, for example, Beko CS 310020) holes for hinges are provided only on one side. In this case, you will have to drill new ones. Here's how to do it right:

• 📏 Marking: Use the old holes as a template. Attach the loop to the opposite side and mark with a pencil the places for drilling.
• 🔨 Drilling: Use a metal drill with a diameter of 4-5 mm (depending on the bolts). Drill at low speeds to avoid damaging the enamel.
• 🔧 Thread: If the holes are too large, use threaded bushings (can be purchased at a hardware store).

⚠️ Attention: When drilling do not tilt the drill —the holes must be strictly perpendicular to the surface. Otherwise, the hinges will be skewed and the door will not close tightly. If you are not confident in your skills, it is better to contact a specialist.

For models with No Frost (for example, Beko RCSK 250M20) drilling can be dangerous: they pass inside the walls refrigerant pipes. In this case:

• Use magnetic search engine (device for detecting metal pipes in walls).
• Drill at a minimum depth sufficient to attach the loop.
• If in doubt, refuse to drill yourself and call a service engineer.

Typical mistakes and how to avoid them

Even with careful work, you can make mistakes that will lead to problems with the refrigerator. Here are the most common of them and ways to prevent them:

One of the most insidious mistakes is Incorrect installation of the magnetic seal. If, after rearranging, the door closes with difficulty or condensation forms on the walls, most likely the seal is deformed or installed crookedly. To fix this:

1. Heat the seal with a hairdryer (temperature no higher than 60°C).
2. Insert it back into the groove, starting from the top corner.
3. Close the door and wait 12–24 hours - the rubber will “take” a new shape.

What will happen if the door is left incorrectly adjusted?

Loose closure will lead to constant operation of the compressor, which will increase energy consumption by 20–30% and shorten the service life of the refrigerator. In addition, ice will form on the back wall (even in models with No Frost), and food will begin to deteriorate faster due to unstable temperatures.

Another common problem is creaking of hinges after rearrangement. This happens due to:

• 🔩 Insufficient lubrication.
• 🔧 Misalignment of hinges.
• 🌡️ Temperature deformation of the metal (if the refrigerator is only that they have defrosted).

To eliminate the squeak:

1. Lubricate the hinges with silicone grease (do not use petroleum-based oils!).
2. Loosen the bolts, adjust the position of the door and tighten again.
3. Let the refrigerator stand for 1-2 days - the metal will “get used” to the new position.

Peculiarities of rearrangement for different Beko models

Refrigerators Beko are divided into several series, each of which has its own nuances when rearranging the door. Let's consider the most popular:

1. Single-chamber refrigerators (CS, CN series)

For example, Beko CS 310020 or CN 325120. Features:

• 🔧 The hinges are attached to 2-3 bolts, the holes are symmetrical.
• 🔄 The seal does not require rearrangement (suitable for both sides).
• ⚡ The motor-compressor is located at the bottom - be careful when drilling.

2. Two-chamber with bottom freezer (GNE, RCSK series)

Models type Beko GNE 114120 or RCSK 250M20. Difficulties:

• 🚪 The door is heavier due to the double chamber - an assistant is definitely needed.
• 💧 Dispenser hoses are possible (in models with Water Dispenser).
• ❄️ System No Frost requires care when drilling.

3. Side-by-Side (SSB, WMI series)

For example, Beko SSB 550 or WMI 25022. These models:

• 🔀 They have two doors. are hung separately.
• 📺 Often equipped with a display - the cables need to be disconnected.
• 🛠️ The hinges are more massive, additional tools may be required (12 mm wrench).

For refrigerators with French Door (for example, Beko RFNE315E20S) relocating the door is an extremely difficult task, often requiring disassembly of the top panel. In such cases, it is better to contact a service center, especially if the refrigerator is under warranty.

Care after rearrangement: how to extend the life of the mechanism

After successfully rearranging the door, the refrigerator requires special care in the first weeks. Here's what you need to do:

• 🧴 Lubricating the hinges: Apply silicone grease to the hinge hinges every 3-6 months. This will prevent squeaking. and wear.
• 🧹 Cleaning the seal: Wipe the rubber band with soapy water (once a month) to remove grease and dirt that can impair the seal.
• 🔧 Adjusting the hinges: Check the tightness of the closure every 2-3 months. If necessary, tighten the bolts.
• ❄️ Defrosting: If the refrigerator is not No Frost, defrost every 6 months to avoid door deformation from ice.

⚠️ Attention: If, after rearranging, the door begins open spontaneously, the problem may be:

• Diskewed hinges (need to be adjusted with a hexagon).
• Wear of the seal (replacement is required).
• Uneven floor (use a level to check).

For models with No Frost (for example, Beko RCSK 250M20) after moving the door, the noise of the fan may temporarily increase. This is normal. - the system adapts to the new position of the door. If the noise does not disappear after 2-3 days, check:

• Closing tightness (the seal may not fit properly).
• Location of products (are they blocking the ventilation holes).

FAQ: Frequently asked questions about moving the Beko door

Is it possible to hang the door of a Beko refrigerator with No Frost yourself?

Yes, but with caution. The main thing is not to damage the refrigerant tubes when drilling new holes. In models with No Frost tubes run close to the walls, so use a magnetic finder before drilling. If you are not sure, it is better to call a specialist.

How much does it cost to rehang a door at a service center?

The cost depends on the model and region. On average:

• For single-chamber refrigerators: 1,500–2,500 ₽.
• For two-chamber refrigerators: 2,000–3,500 ₽.
• For models with a display: 3,000–5,000 ₽.

The price may increase if new holes need to be drilled or the seal needs to be replaced.

What to do if, after rearranging, the door does not close tightly?

Possible causes and solutions:

1. Hinges are skewed: Loosen the bolts, level the door and tighten it again.
2. Deformation of the seal: Heat it with a hairdryer (50–60°C) and reinstall it.
3. Garbage ingress: Check the grooves of the seal and clean them.

If the problem persists, the seal may be worn out and requires replacement.

Is it necessary to defrost the refrigerator before moving the door?

Required if:

• The refrigerator does not No Frost.
• There is ice on the seal or hinges.
• You plan to drill new holes (moisture can get on the metal and cause corrosion).

For models with No Frost defrosting does not is required, but it is recommended to disconnect the refrigerator from the network while working.

Is it possible to hang the door on a Beko refrigerator with a display?

Yes, but it is more difficult. You will need:

1. Disconnect the display cable (carefully so as not to damage the connector!).
2. Move the loops, taking into account the location of the wires.
3. Connect the cable back, making sure that it is not pinched.

If you have experience working with there are no electronics - it’s better to contact the service.