Replacing a light bulb in a Beko refrigerator: instructions with photos and videos

Burnt light bulb in the refrigerator Beko is a problem that almost all every owner of equipment of this brand. An unpleasant surprise is usually discovered in the evening when you open the door and the light inside does not come on. Fortunately, replace the lamp you can do it yourself in 10–20 minutes, without the help of a specialist. The main thing is to know type of lampcorrectly turn off the power and carefully remove the lampshade.

In this article you you will find step-by-step photo instructions for models Beko with an upper and lower lamp positiona list of necessary tools, as well as tips on choosing a replacement. We will analyze the nuances for refrigerators with LED backlight and traditional incandescent lamps, and also tell you how to avoid common mistakes during repairs. If your model is equipped with a door closing sensor, do not miss the section about resetting errors after replacement!

Signs of a faulty lamp in the refrigerator Beko

Before you rush to disassemble the refrigerator, make sure that the problem is in the light bulb. Here are the key symptoms:

• 💡 The light does not light up when the door is opened, although the refrigerator is working (the noise of the compressor is heard).
• 🔌 The lamp is blinking or it lights dimly - a sign of imminent burnout or problems with the cartridge.
• ⚡ Clicks when turned on light - indicates a short circuit in the backlight circuit.
• 🔧 The lampshade is heating up - if the housing around the lamp is hot, this may be due to a malfunction of the socket.

If the lamp does not works display or control buttons, the problem may lie in the power supply - in this case it is better to contact a service center. Also check if the automatic on the socketworked: sometimes the refrigerator is connected through a separate line with protection.

What lamps are used in Beko refrigerators

The type of lamp depends on models i year of manufacture refrigerator. The table below shows common options for equipment Beko last 10 years:

In modern models (after 2018), they most often install LED backlight, which is more economical and more durable. However, in budget series (Beko CS, CN) you can still find incandescent lamps with a base E14. Halogen lamps typical for premium refrigerators with a freshness zone.

🔍 How to determine the type of lamp? Look at the technical data sheet of the refrigerator (section “Technical Specifications”) or take a photo of a burnt-out lamp - you can choose an analogue based on the shape of the base and markings. If the documentation is lost, use search by model on the official website Beko.

Preparation for replacement: tools and safety measures

Before you start work, unplug the refrigerator - remove the plug from the socket or turn off the machine on the panel. This is a must, even if you are an experienced electrician. Also prepare:

• 🔧 Phillips screwdriver (usually PH2 size is sufficient).
• 🛠️ Flat screwdriver or a plastic pick for removing the clips.
• 💡 New lamp (preferably original or certified analog).
• 🧤 Gloves - so as not to leave fingerprints on the lampshade and not get cut.
• 📸 Phone - for photographing the process (useful during reassembly).

If it is installed in the refrigerator halogen lamp, do not touch its glass flask with your bare hands - grease marks lead to overheating and rapid failure. Use a napkin or gloves.

⚠️ Attention: In models Beko with the system No Frost the lamp can be fixed to the inner panel of the freezer. If you are not sure about the location of the lamp, watch a video disassembly for your model on YouTube - channels like “Refrigerator Repair” often publish detailed instructions.

Unplugged the refrigerator|

Prepared tools and a new lamp|

Took pictures of the original position of the parts|

Wearing gloves (for halogen lamps)|

Checked that the refrigerator door opens freely (does not interfere with dismantling)

-->

Step-by-step instructions: how to remove the lampshade and replace the lamp

The replacement process depends on light design i lamp location. Below is a universal instruction, suitable for 90% of models Beko (exceptions are refrigerators with LED panels, for them see the next section).

1. Dismantling the lampshade

The lampshade in refrigerators Beko is usually mounted on latches or screws. Algorithm of actions:

1. Open the refrigerator door to the maximum angle.
2. Find the lampshade - it is located on the ceiling or back wall of the main chamber.
3. If the lampshade is secured with screws (more often in older models), unscrew them with a Phillips screwdriver.
4. If the lampshade is latched, carefully pry it with a flat screwdriver on one side and pull it towards you. Do not make excessive efforts - the plastic may crack!

2. Removing the lamp

After removing the lampshade, you will see a socket. Depending on the type of base:

• For E14/E27: grab the bulb and carefully unscrew the lamp counterclockwise.
• For G4/G9: pull the lamp towards you (without turning).
• For LED module: disconnect the power connector (see the next section).

💡 Tip: If the lamp is “stuck” to the socket, do not try to unscrew it by force. Spray the base WD-40 or medical alcohol, wait 5 minutes and try again.

3. Installing a new lamp

Screw or insert the new lamp into the socket. Make sure she fits tightly and does not wobble. For incandescent and halogen lamps, check the power - it should match the original one (see table above).

4. Reassembly

Install the lampshade into place and secure it with screws or latches. Plug in the refrigerator and check the lighting operation. If the light does not light up, check:

• The tightness of the contacts in the socket.
• The integrity of the wiring (there are no breaks or melts).
• The correct installation of the lamp (perhaps it is not screwed in completely).

What to do if does the lamp not work again?

If after replacement the lamp does not light, the problem may be:

1. Cartridge —the contacts have oxidized or it is cracked.

2. Door switch —it is responsible for turning on the light when the door is opened. Check it with a multimeter (there should be a resistance of 0 Ohm when pressed).

3. Power supply —in LED refrigerators the driver may burn out.

In these cases, it is better to contact specialist.

Features of replacing LED lamps in Beko refrigerators

If your refrigerator is equipped with LED-backlit (for example, model Beko GNE V320X, RCNA 400E20), the replacement process is different. There is no traditional cartridge - instead it is used LED moduleconnected to the board via a connector.

🔧 You will need:

• New LED module (original art. Beko 2405000100 or equivalent).
• Tweezers for carefully removing the connector.
• Mulmeter (for checking the voltage on the contacts).

Procedure:

1. Remove the lampshade (as described above).
2. Disconnect the power connector from the LED module. Be careful - the contacts are fragile!
3. Remove the old module from the seat (usually it is secured with latches or double-sided tape).
4. Install the new module and connect the connector. Polarity is important - there are markings on the board and module + and –.

⚠️ Attention: In LED refrigerators Beko after 2020 there may be protection against reverse polarity. If you confuse + and –, the module will not light up, but it will not burn out either - just reconnect it.

📌 Where to buy an LED module? Look for original spare parts on the sites:

• 🛒 Official Beko store (section "Spare parts").
• 🛒 220-Volt (enter the art. 2405000100).
• 🛒 ChipDip (for radio amateurs - there are similar modules there).

Typical mistakes and how to avoid them

Even experienced craftsmen sometimes make mistakes when replacing a lamp. Here are the most common ones. common:

Another common problem is poor fit of the lamp. data-i="239">🔹 Are all the latches of the lampshade in place? after assembly, this leads to moisture getting on the cartridge and corrosion of the contacts. To avoid this, check:

• 🔹 Are all the latches of the lampshade in place?
• 🔹 Is there any distortion - the lampshade should sit smoothly, without gaps.
• 🔹 Do the wires interfere with closing (relevant for models with a top-mounted lamp).

If after replacement the lamp works, but blinking, the reason may be:

• 🔌 Poor contact in the socket (clean the contacts with alcohol).
• 🔋 Unstable voltage in the network (use a stabilizer).
• 💡 Poor quality lamp (buy trusted brands: Osram, Philips, Narva).

Replacing the lamp in Beko refrigerators with the No Frost system

In models with No Frost (for example, Beko RCSK 310M20, DS 333020) the lampshade is often located behind the inner panel of the freezer. This complicates access, but the replacement algorithm remains similar.

Differences from the standard procedure:

1. Before removing the panel defrost the freezer (1-2 hours is enough) so that the ice does not interfere. dismantling.
2. The lampshade can be attached to hidden latches -they need to be carefully pressed out with a flat screwdriver.
3. In some models the lamp is connected through sealed connector —do not pull the wires, but press the latch.

🔧 Advice for No Frost: If, after replacing the lamp, the refrigerator starts make more noise, check whether the fan blades have moved. Sometimes when dismantling the panel, its blades have not moved. touch the body.

⚠️ Attention: In refrigerators Beko with No Frost and electronic control (display on the door) after replacing the lamp it may work error E1 or E2. To reset it, unplug the refrigerator for 5 minutes, then turn it on again. If the error remains, the board must be re-flashed.

FAQ: Frequently asked questions about replacing the lamp in the refrigerator. Beko

🔹 Is it possible to replace an incandescent lamp with an LED?

Technically it is possible, but only if the LED module is designed for the same voltage (usually 220V). Most refrigerators Beko use 220V, but some models with electronic control may have 12V or 24V. Check the marking on the socket or in the technical data sheet. Also keep in mind that the LED lamp must physically fit into the lampshade - sometimes the entire backlight module needs to be replaced.

🔹 Why does a new lamp burn out quickly?

There are several reasons:

1. Power surges - use stabilizer.
2. Bad contact in the socket —clean the contacts with sandpaper or alcohol.
3. Overheating —check whether the lamp is covered by thermal insulation.
4. Poor quality lamp —buy trusted brands.

If the problem persists, the block may be faulty power supply (for LED) or door switch.

🔹 How to remove the lampshade if it cannot be removed?

In some models Beko (for example, Beko GNE 110620) the lampshade is attached to hidden latches. Try:

1. Gently pull the lampshade towards you, slightly shaking it left and right.
2. Pry it with a screwdriver with a thin tip around the perimeter (start with corner).
3. Watch the video disassembly for your model - often the lampshade is held on by 2-4 latches.

If the lampshade is cracked during dismantling, do not try to glue it - replace it with a new one (art. Beko 2401000300 for most models).

🔹 What to do if after replacing the lamp the refrigerator does not turn on?

Probable reasons:

• Short circuit —check the cartridge for melting.
• Protection has activated —turn off the refrigerator for 10 minutes, then turn it on again.
• Wiring is damaged - inspect the wires for breaks.
• Wrong LED connection - check the polarity.

If the refrigerator does not respond to turning on, call a technician - perhaps the fuse on the control board has blown.

🔹 Where can I find the lamp connection diagram for my model?

Connection diagrams can be found:

• B technical data sheet (section "Electrical diagram")
• On the websites Beko support (enter the refrigerator model).
• On the forums masters (for example, Mastergrad - look for a topic based on your model).

For most household tasks, a diagram is not needed - just follow the instructions above. But if you plan to modify the backlight (for example, install an RGB strip), the diagrams will help you avoid mistakes.