Re-hanging refrigerator doors Biryusa is a task that owners face when moving, renovating a kitchen, or simply wanting to change sides opening. Two-chamber models (for example Biryusa-10D, Biryusa-22K or Biryusa-26S) structurally allow you to rehang the door yourself, but the process requires accuracy and knowledge of the nuances. In this article - step-by-step algorithm taking into account the features of fastenings, typical errors and tips for setting up after installation.
Many are afraid of damaging the seal or breaking the tightness of the chambers, but with the right approach the risks are minimal. The main thing is do not skip the step of adjusting the hinges after rehanging, otherwise the door will sag or close poorly. We will analyze the tools that will be needed, the fastening diagram for different models and give recommendations for caring for the seal after work.
If your refrigerator Turkish was produced before 2010, check the presence rubber plugs on the opposite side of the case - in the old ones models they might not be available. Modern versions (for example, Biryusa-130 or Biryusa-140) are equipped with everything necessary for hanging, but sometimes you need to purchase additional fasteners.
Preparation: tools and working conditions
Before you begin, make sure you have everything you need. Minimum set of tools:
- 🔧 Phillips screwdriver (better with a magnetic tip - it’s easier to work with small screws).
- 🔨 Hex key (size depends on the model, usually 4 or 5 mm).
- 📏 Level (to check evenness installation of the door after installation).
- 🧴 Silicone grease (for processing the seal and hinges).
- 🧲 Magnet or tweezers (will help if the screw falls into a hard-to-reach place).
Also prepare clean cloth for wiping parts and plastic plugs (if they are not included in the kit, you can cut them from scrap materials). It is more convenient to work on flat surface —if the refrigerator is on a carpet, place plywood or cardboard under it to avoid distortions.
⚠️ Attention! If the refrigerator is connected to the water supply (models with an ice maker), turn off the water and disconnect the hose before starting work. Otherwise, you risk flooding the kitchen.
Door fastening diagram: what you need to know before disassembling
Double-chamber refrigerators Biryusa have two independent doors (refrigerator and freezer compartments), each of which is attached to two hinges: upper and lower. Structurally, the hinges are:
- 🔄 Removable (fastened with screws, easily dismantled).
- 🔗 Non-removable (found in older models, require complete removal of the door).
On the opposite side of the body (where the door will be hung) there are usually technological holesclosed with plugs. In new models (Biryusa-130, Biryusa-140), these holes are standard, but in refrigerators produced before 2015, technological holes may be required additional fasteners.
Below is a table with typical fastening sizes for popular models:
| Refrigerator model | Screw diameter, mm | Hinge type | Number of plugs |
|---|---|---|---|
| Biryusa-10D, Biryusa-18K | 5 | Removable | 4 (2 for each door) |
| Biryusa-22K, Biryusa-26S | 6 | Removable | 6 (additionally for attaching the handle) |
| Biryusa-130, Biryusa-140 | 4 (upper hinges), 5 (lower) | Removable with lock | 8 (including plugs for the handle) |
⚠️ Attention! In models c electronic display (for example, Biryusa-22K-003) the door control wires run inside the hinge. When dismantling do not pull wire - first disconnect the connector!
Step-by-step instructions: how to remove and rehang the door
The algorithm is the same for most two-chamber models Biryusa, but may differ in details. Let's consider the universal procedure:
- Unplug the refrigerator and wait until it defrosts (if the freezer is covered with ice).
- Remove the decorative plugs from the opposite side of the case (where there will be new hinges). Use a flat-head screwdriver, prying them up carefully so as not to damage the plastic.
- Remove the top hinge:
- 🔧 Unscrew the screws securing the hinge to the body (usually 2-3 pieces).
- 🔄 Hold the door so that it does not fall after removing the hinge.
- Remove the bottom hinge:
- 🔧 Unscrew the screws (a hexagon may be required).
- 📌 In some models, the bottom hinge is secured with an additional bolt from below - don’t miss it!
☑️ Checklist before re-hanging the door
⚠️ Attention! If after rehanging the door does not close tightly, check:
- 🔹 Correct installation thrust washers (they must be in place, otherwise the door will "walk").
- 🔹 Condition sealing rubber — perhaps it was deformed during dismantling.
- 🔹 Floor level - The refrigerator must stand level, otherwise the door will warp.
Adjusting the door after rehanging
Even if the hinges are fastened correctly, the door may sag or non-fitting to the body. This can be corrected by adjustment:
- 🔧 The upper hinge responsible for adjusts the door to the body. If the door “moves away” at the top, tighten the hinge screws clockwise.
- 🔧 Bottom hinge adjusts door height. If the door clings to the body, loosen the bottom screws and adjust the position.
To check the tightness, use test with a sheet of paper:
- Insert the sheet between the seal and the body.
- Close the door and try to pull out the sheet.
- If the sheet pulls out without effort the seal does not fit. Tighten the hinges or replace the elastic band.
What to do if the door still does not close after adjustment?
The problem may be in deformed seal or distortion of the refrigerator body. In the first case, the elastic needs to be heated with a hairdryer (temperature 50–60°C) and leveled with your hands. In the second, adjust the legs of the refrigerator according to the level.
⚠️ Attention! data-i="221">Biryusa-130E After adjustment, check door closing sensor operation (if it is in your model). In refrigerators Biryusa with electronic controls (Biryusa-130E, Biryusa-140E), incorrect position of the door can cause error on the display (code E1 or E2). In this case, reset the error by holding the button for 5 seconds. Super Cool 5 seconds.
Typical mistakes and how to avoid them
Even when following the instructions, you can make mistakes that will lead to k hinge breakage or tightness failure. Let's look at the most common ones:
- 🚫 Ignoring the plugs. If you do not close the technological holes after rehanging, dust and moisture will get inside the case, which will accelerate corrosion.
- 🚫 Tightening the screws. Excessive tightening force may strip the threads in the plastic hinge housing. Tighten the screws until the stop, but without fanaticism.
- 🚫 Failure to follow the sequence. If you remove the bottom hinge first, the door may fall and damage the seal or the hinge itself.
- 🚫 Using the wrong tools. A screwdriver of the wrong size or without a magnetic tip increases the risk of losing the screws inside the case.
On models Biryusa-22K i Biryusa-26S the bottom hinge of the freezer compartment has hidden lock —a plastic latch that needs to be pressed out with a screwdriver before removal. If you do not notice it, the hinge will not be removed, and the case may crack.
Care for the seal and hinges after rehanging
After installing the door in a new location sealing rubber and loops require special attention:
- 🧼 Cleaning the seal. Wipe the rubber with soapy water, then apply a thin layer of silicone grease (do not use oils - they destroy the rubber!).
- 🔧 Lubricating the hinges. Place 1-2 drops of machine oil or WD-40 on the hinge axis to avoid squeaking.
- 📏 Gap control. Once a month, check if any gaps have appeared between the door and the body. If necessary, tighten the hinges.
If the seal has lost its elasticity (this is noticeable by cracks or constant frost deposits on the walls), it is needed replace. For models Biryusa rubber bands are suitable:
- 🔹 Universal (for example, Indesit 48123456789, suitable for most two-chamber refrigerators).
- 🔹 Original (ordered by model code, for example, for Biryusa-130 - art.
60.3201.101).
⚠️ Attention! Do not use sealants abrasive agents or hard brushes - they damage the surface of the rubber, which leads to loss of tightness.
Features overweight in models with a display
Refrigerators Biryusa with electronic control (Biryusa-130E, Biryusa-140E, Biryusa-22K-003) have additional nuances:
- 📱 The wires of the closing sensor take place inside the upper loop. When dismantling, carefully disconnect the connector (usually it is secured with a latch).
- 🔌 Control unit may be located on the door or body. In the first case, you will need to move it to the other side (extended wires are included in the kit).
- ⚙️ Reset settingsAfter repositioning, the calibration of the sensors may be lost - perform a reset by holding. button
Super Cool+Fridge Temp10 seconds.
In models with ice maker (Biryusa-26SL) before rehanging you must:
- Turn off the water supply.
- Drain the remaining water from the system (button
Drainin the menu). - Move the water supply hose to the other side (required extension cord).
FAQ: answers to frequently asked questions
Is it possible to hang the Biryusa refrigerator door yourself if you have no experience?
Yes, but only if you are confident in your abilities. The main thing is to follow the instructions. Start at the top hinge, holding the door so it doesn't fall. If the refrigerator is under warranty, it is better to contact a service center - independent repairs may void the warranty. Take your time and follow the instructions. Start at the top hinge, holding the door so it doesn't fall. If the refrigerator is under warranty, it is better to contact a service center - repairing it yourself may void the warranty.
How long does it take to rehang the door?
On average - 1–1.5 hoursif there are no complications. Most of the time is spent on adjusting the hinges and checking the tightness. In models with an electronic display, the process may take up to 2 hours due to the need to move the wires.
What should you do if, after rehanging, the refrigerator begins to operate loudly?
This may be due to:
- 🔹 By skewing the body (check the floor level and adjust the legs).
- 🔹 By touching the door to the body (tighten the hinges).
- 🔹 By breaking the fastening compressor (if the door touched its fastenings during dismantling).
If the noise does not disappear, call a technician - you may need to diagnose the compressor.
Do you need to defrost the refrigerator before rehanging it?
Absolutely! If there is ice in the freezer, it may damage the seal when the door is removed. In addition, condensation on parts impairs the adhesion of tools to screws. Defrost the refrigerator for at least 4-6 hours.
Where can you buy plugs for the holes if they are not included?
Plugs can be:
- 🛒 Order from the official dealer Turk (by model code).
- 🛠️ Cut from white plastic (a bottle cap or a stationery folder will do).
- 🔍 Choose universal ones in spare parts stores for household appliances (for example, art.
PLUG-5for holes with a diameter of 5 mm).