How to correctly insert drawers into the freezer of a Bosch refrigerator: step-by-step instructions with photo

Refrigerator owners Bosch often face the need to remove, rearrange or install plastic drawers in the freezer. It would seem like a simple operation, but incorrect installation can lead to jamming of the guides, skewing of the door, or even breakage of the fasteners. The problem is especially pressing after defrosting, when the drawers are washed separately and then tried to be inserted into place “by eye.”

The design of freezers Bosch (series KGN, KIN, KIS etc.) assumes a strict installation sequence: first the lower drawers, then the upper ones, taking into account the latches and grooves. This article contains detailed diagrams for different models photos of key points, as well as tips on how to avoid common mistakes. If your refrigerator is equipped with a NoFrost or LowFrostsystem, pay attention to the features of the fastenings - they differ from drip models.

Preparation: what needs to be done before installing the drawers

Before inserting boxes back, make sure that the freezer is ready for this. Drawers cannot be installed in the chamber with ice residue on the walls or guides - this will lead to deformation of the plastic when freezing. Carry out a visual inspection:

• 🔹 Chamber temperature: should not be lower than +5°C (if the refrigerator was turned off to defrost). It is prohibited to insert boxes into a frozen chamber - the plastic becomes brittle.
• 🔹 Cleanliness of the guides: check if there are crumbs, ice or condensation inside the grooves. Wipe them with a dry cloth.
• 🔹 Integrity of drawers: inspect the containers for cracks, especially in the corners. Damaged drawers can jam the mechanism.

If you defrosted the refrigerator, wait until the moisture has completely evaporated from the door seals. Otherwise, when installing the boxes, condensation may form on the walls, which will subsequently lead to icing. To speed up the process, use a fan or leave the door open for 10–15 minutes.

⚠️ Attention: In models Bosch with a system VitaFresh the bottom drawers of the freezer often have additional fastenings for freshness zones. Do not confuse them with the main guides - they are designed to fix the dividers, not the drawer itself.

Guide diagram: how the grooves are arranged in a Bosch freezer

The design of freezers Bosch provides for two types of drawer fastenings:

1. Slides on the side walls —the most common option. The box is inserted into the grooves on the left and right, and then slides back until it clicks.
2. Central guide —used in models with “basket” type drawers. Here it is important to align the protrusion at the bottom of the box with the groove at the bottom of the chamber.

Let's take a closer look at each type:

To determine the type of fastening in your model, inspect the inside walls of the freezer. If you see horizontal plastic or metal runners on the sides, this is the first type. If there is a noticeable groove in the center on the bottom of the chamber, and a protrusion on the drawer - the second type.

How to find the model of your Bosch refrigerator?

The model is indicated on a sticker inside the chamber (usually on the left wall) or on the back panel of the refrigerator. Designation format: letter K, then 2-3 letters (series), numbers (volume) and letter code (modification).

Step-by-step instructions: how to insert a box into a Bosch freezer

Consider a universal algorithm for most models. If your refrigerator is equipped with a system NoFrost, skip step 1 - ice does not form in such chambers.

1. Tilt the drawer at an angle of 15–20° (the front part is higher than the back). This is necessary so that the rear protrusions of the drawer fit into the grooves on the walls of the chamber.

2. Wind the back of the drawer into the grooves, then slowly lower the front part. In models with a central guide, first align the protrusion on the bottom of the drawer with the groove in the chamber.

3. Press the front panel of the drawer until a characteristic click is heard. This means that the latches have snapped into place. In some models (KGN39XL30) there is no click - the drawer simply sits tightly in place.

4. Check the movement of the drawer: it should slide out smoothly, without jamming. If the drawer is difficult to move, remove it and repeat installation.

For drawers with dividers (for example, in models KIN86AF30), first install the main container, then insert the partitions into the grooves on its walls. Do not try to insert the dividers separately - they do not have their own fastenings to the chamber.

⚠️ Attention: In refrigerators Bosch with the function SuperFreezing the bottom drawer of the freezer often has reinforced guides. When installing it, more force is required to secure it. Do not confuse this with jamming!

Common mistakes and how to avoid them

Even with the apparent simplicity of the process, users often make mistakes that lead to breakdowns. Here are the most common of them:

• 🚫 Installing drawers in reverse order. The top drawers cannot be inserted before the bottom ones - they block access to the guides. Always start with the lowest container.
• 🚫 Ignoring the latches. If you don't wait for the click, the drawer may fall out when you open the door. In models KIS87AF30 this leads to deformation of the plastic latches.
• 🚫 Excessive force. If the box doesn't fit, don't push harder—check to make sure it's oriented correctly. In freezers Bosch with a system LowFrost guides often have hidden grooves that are easy to miss.
• 🚫 Installation of wet boxes. Condensation on plastic expands when it freezes and can crack the container. Always dry the boxes before installation.

Pay special attention to models with with sliding glass shelves in the freezer (for example, KGV36VW30). Here the drawers are mounted not on guides, but on special slides. When installing such containers:

1. First, fix the slides in the grooves of the chamber.
2. Then carefully lower the box onto them, aligning the holes in the bottom with the protrusions on the slide.

Features for models with NoFrost and LowFrost

Refrigerators Bosch s systems NoFrost i LowFrost have a specific design of the freezer chamber, which affects the installation of drawers:

• 🌬️ NoFrost: Ventilation holes are located on the back wall. The boxes here often have perforated bottom for air circulation. When installing, make sure that the holes are not blocked.
• ❄️ LowFrost: The guides can be coated with a special anti-icing coating. Do not use abrasive detergents when cleaning grooves - this will damage the protective layer.

In models with NoFrost (for example, KGN39VL30) drawers are often equipped with additional latches on the back wall. They prevent the containers from moving when the fan is running. When installing such boxes:

1. Place the front part into the grooves.
2. Tilt the box down so that the rear latches fit into the holes on the chamber wall.
3. Press the front panel until click.

⚠️ Attention: In refrigerators Bosch s NoFrost it is not recommended to use drawers from other models - even if they are identical in appearance. Differences in the location of the ventilation holes can lead to uneven freezing.

How to remove a jammed drawer: emergency measures

If a drawer is stuck in the freezer, do not try to pull it out by force - this may break the guides. Proceed according to the following algorithm:

1. Unplug the refrigerator from the network and wait until the ice (if any) melts a little. In models with NoFrost this step can be skipped.

2. Gently rock the box from side to side, while simultaneously pulling it towards you. The amplitude of movements is no more than 1–2 cm.

3. Use a plastic spatula (for example, to clear ice) to pry the box from below. Metal objects cannot be used - they will scratch the plastic.

4. If the drawer does not budge, remove the front panel freezers (it is secured with latches) and try to release the guides from the inside.

As a last resort, you can dismantle the runners. To do this:

1. Unscrew the screws securing the guides to the walls of the chamber (a Phillips screwdriver is required).
2. Remove the slides and remove the drawer.
3. Install the guides back, making sure that they fit snugly against the walls.

After removing the jammed drawer, inspect the guides for deformation. If the plastic is bent, try straightening it with a hairdryer (heat the problem area and gently shape it).

Care for drawers and slides: how to extend their service life

To avoid problems with the installation of drawers in the future, follow these simple rules:

• 🧼 Wash drawers warm water with a mild detergent (e.g. children's dishes) at least once every 2 months. Do not use hard sponges.
• 🍃 Dry containers in the air after washing. Do not place them on the battery to dry - the plastic may become deformed.
• 🔧 Lubricate the guides with silicone grease (once a year). This will prevent squeaking and make the drawers move easier. Do not use edible oils - they spoil the plastic.
• ❄️ Do not overload drawers. The maximum load for plastic containers Bosch is 10 kg. For glass shelves - 15 kg.

In models with a system LowFrost periodically check the condition of the rubber seals on the drawers. If they have lost their elasticity, replace them - this will prevent the guides from icing.

To clean the grooves in the freezer, use toothpick or cotton swabmoistened in a vinegar solution (1:1 with water). This will help remove mold and grease deposits. After cleaning, wipe the guides with a dry cloth.

FAQ: answers to frequently asked questions

Is it possible to put drawers from a Bosch freezer into a refrigerator camera?

No, this is not recommended. Freezer drawers are made of more durable plastic designed to withstand low temperatures. They may become brittle and crack in the refrigerator. In addition, their dimensions rarely coincide with the grooves in the main chamber.

Why does the new drawer not fit into the grooves?

Most likely, you purchased a drawer from a different model. Even visually identical containers may have differences in the location of the tabs or latches. Check the box article number with the original one (it is indicated on the sticker on the inside). For refrigerators Bosch original spare parts can be ordered using the code starting with 0064.

How to remove the drawer if the latch is broken?

If the latch on the front panel of the drawer is broken, carefully pry it up with a flat screwdriver and remove the panel. Then remove the drawer from the top. A temporary solution may be to fix the panel with double-sided tape (but this does not guarantee reliability). For a complete repair, you will need to replace the latch (part 00645892 for most models).

What to do if the box moves out on its own after installation?

This indicates wear of the latch or guides. Try:

1. Wipe the guides with alcohol - sometimes stickiness occurs due to fatty deposits.
2. Slightly bend the latches (plastic "antennae" on the drawer) with pliers for a tighter fit.
3. If the problem persists, replace the guides or drawer.

Can the drawers be washed in the dishwasher?

Depends on the refrigerator model. Drawers made of polypropylene (marked PP or 5 in a triangle) can be washed in the dishwasher at temperatures up to 50°C. Boxes made of polystyrene (PS or 6cannot be washed in a machine - they are deformed. Look for the exact information on the sticker on the inside of the box.